User manual

13
© 2009, Elektro-Automatik GmbH & Co. KG
EN
Analogue interface
All models feature a 12 pin analogue interface on
the front of the device. It can be used to monitor the
device condition, as well as remotely start/stop the
charging procedure.
Also see next page.
Handling
Powering the device
The device does not feature a power switch. When
connecting it to mains, it is immediately ready to
work.
After switching mains off the device stores the last
state (selected mode, output condition) in order to
restore it automatically at the next start. Thus it can
continue to work after an interruption like a blackout
etc.
Adjusting the output voltage
The nominal output voltage is seperated into three
selectable voltage ranges, each approximately 1/3
of the nominal voltage. For details see the „Technical
specications“.
About the device
Technical specications
PS 880-40R PS 880-60R PS 8360-10R PS 8360-15R
Mains input
Input voltage 90….264V 90….264V 90….264V 90….264V
Frequency 45….65Hz 45….65Hz 45….65Hz 45….65Hz
Power factor correction >0.99 >0.99 >0.99 >0.99
Input current at 230V and full load approx. 4.8A approx. 7.5A approx. 4.8A approx. 7.5A
Input current at 100V and full load approx. 11.4A approx. 11.4A approx. 11.4A approx. 11.4A
Output - Voltage
Nominal voltage U
Nom
80V 80V 360V 360V
Voltage range 1 0V...30V 0V...30V 0V...120V 0V...120V
Voltage range 2 30V...60V 30V...60V 120V...240V 120V...240V
Voltage range 3 60V...80V 60V...80V 240V...360V 240V...360V
Stability at 10-90% load <0.05% <0.05% <0.05% <0.05%
Stability at ±10% ¨ U
In
<0.02% <0.02% <0.02% <0.02%
Ripple
<70mV
PP
<70mV
PP
<100mV
PP
<100mV
PP
Regulation 10-100% load <2ms <2ms <2ms <2ms
Output - Current
Nominal current 40A 60A 10A 15A
Stability at 0-100% ¨ U
Out
<0.15% <0.15% <0.15% <0.15%
Stability at ±10% ¨ U
In
<0.05% <0.05% <0.05% <0.05%
Ripple
<100mA
PP
<100mA
PP
<15mA
PP
<15mA
PP
Output - Power
Nominal power 1000W 1500W 1000W 1500W
Nominal power at U
In
<150V
1000W 1000W 1000W 1000W
Miscellaneous
Operation temperature 0….40°C 0….40°C 0….40°C 0….40°C
Storage temperature -20….70°C -20….70°C -20….70°C -20….70°C
Humidity <80% <80% <80% <80%
Dimensions (WxHxD) 90x360x240mm 90x360x240mm 90x360x240mm 90x360x240mm
Weight 8.9kg 9.2kg 8.9kg 9.2kg
Article No. 21540107 21540108 21540109 21540110
Safety
EMC standards
Overvoltage category
Protection class
EN 60950
EN 61204, EN 55022 Class B
Class II
Class I
The built-in trimmer is a 10-turn type and the ap-
proximate 10 rotations from left stop to right stop
correspond to the selected range.
Switching output on or off
The pushbutton „On/Off“ is used to switch the power
output on or off, if not inhibited by any error (OVP or
OT) or the device being in remote control. The voltage
set by the trimmer will then be put out immediately.
The output can also be switched off at any time via
pin 8 „Rem-SB“ of the analogue interface and then
on again.
Attention! The pin REM-SB overrides the pushbutton
„On/Off“.
When the output is switched on, the LED „CC“ will
indicate constant current operation (LED is on) or
constant voltage operation (LED is off).
Selecting a voltage range
The pushbutton „Output Range“ is used to select the
output voltage ranges. The output has to be off in
order to select the voltage range.