Wet/Dry Vacuums Polyethylene, Polypropylene, & Steel Operations and Parts Manual Models: 315P 415P 429P 430P 415S 415ST 415PLT
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. WARNING DANGER: Failure to read and observe all DANGER statements could result in severe bodily injury or death. Read and observe all DANGER statements found in your Owner’s Manual and on your machine.
Warning: Operating a machine without observing all labels, decals, etc., could result in injury or damage. Read all machine labels before attempting to operate the machine. Make sure all of the labels are attached or fastened to the machine. Get replacement labels and decals from the manufacturer’s distributor. Warning: Electrical components can “short-out” if exposed to water or moisture. Keep the electrical components of the machine dry. Always store the machine in a dry area.
120 Volt Machine Instructions For Connection To The Power Supply And The Electrical Ground This machine must be connected to the electrical ground to protect the operator from electrical shock. The machine has an approved power cord with three conductors and a plug with three terminals. Connect the plug to a receptacle that has three holes and is connected to the electrical ground. The green (or green and yellow) conductor in the cord is the ground wire.
IMPORTANT INSTRUCTIONS Before use, the equipment must be correctly assembled with all of its components Check that the electrical outlet is correct for use with the plug on the machine Before connecting, check that the specified motor voltage corresponds to the main voltage available Never use the equipment near flammable, explosive or toxic substances: sparks from the motor could cause dangerous reactions.
Periodic Maintenance (Every six to twelve months) 1. Check filter for wear, replace dirt saturated filters that do not respond to normal cleaning. 2. Inspect gasket seals and replace those which have begun to leak. 3. Examine carbon motor brushes and commutator. S8053200 Servicing The Filter The filter is accessed by lifting the head assembly off the tank. The Polyester filter assembly is easily removed by simply lifting the filter basket out of the tank. The cartridge filters they are removed very easily.
Servicing The Vac Motor Carbon Brush Replacement (Replacement Carbon Brushes: Part# S8053200) 1. Disconnect power cord from power source. 2. To access the vac motor, remove the screws that attach the main cover to the head assembly and set the cover to one side. 3. Remove the screws that attach the inner cover to the head assembly and set aside. 4. Remove the carbon brush assembly by removing the 2 screws that attach it to the vac motor. See Figure 1 5.
315 Vacuum Motor Assembly No.
415 Vacuum Motor Assembly No.
429 Vacuum Motor Assembly No.
430 Vacuum Motor Assembly No.
Tank Assembly 315P No. 1 2 3 4 5 6 7 8 9 Part# S82668 S82599 S81300 S81847 S81050 S82846 S82586G6 S82593 S82652AG6VE S80558 Description Complete Tank Assy. Tank, Black Rivet Clamp Screw 5x35 Gasket Retainer Deflector Inlet Cover Caster 13 Qty.
Tank and Cart Assembly 415P, 429P, 430P No. 1 2 3 4 5 6 6a 7 7a 8 9 10 11 12 13 14 15 16 17 Part# S82558 S82637NE S81026 S82584G6 S82846 S82593 S82767 S82652AG6VE S82762AG6VE S81300 S81847 S81050 S82974 S81072-1NE S81860-1NE S81302NE S82559 S82680 S82556 Description Handle Tank, Poly 24g Black Screw 5x30 Retainer, Tank Gasket Deflector Deflector (430P) Inlet Cover w/button Inlet Cover w/button (430P) Rivet Latch Screw Washer, Plastic Support, Handle Front Support, Handle Rear Rivet 4.
Tank Assembly 415ST No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Part# S82993 S81847 S81302 S83629 S83883 S83253 S81026 S82586 S82846 S82593 S82583 S82594 S82608 S82993 S82974 S83629 S83156 S83883 S82968 S82970 S82969 Description Handle Clamp, Tank Rivet 5x19 Screw 5x25 Washer Tank-Steel Screw 5x30 Adapter, Tank Gasket Deflector Adapter, Hose Button Spring Handle Washer Screw 5x25 Screw 5x25 Washer Hook, Tank Swivel Knob, Release 15 Qty.
Cart Assembly 415ST No. 1 2 3 4 5 6 7 8 9 10 11 Part# S83250 S80976 S82557 S80904 S83835 S81012 S80478 S80479 S81979 S83450 S86250 Description Cart Plug Cap, End Wheel Cap Washer Nut Caster, Swivel Screw 5x25 Clip Pad Hand Grip 16 Qty.
Tank Assembly 415S No. 1 2 3 4 5 6 7 8 9 10 11 Part# S82993 S81847 S81302 S83629 S83883 S80476 S81026 S82586 S82846 S82593 S82583 Description Handle Clamp, Tank Rivet 5x19 Screw 5x25 Washer Tank Screw 5x30 Adapter, Tank Gasket Deflector Inlet Cover Qty.
Cart Assembly 415S No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Part# S82993 S80917 S80913 S81301 S80902 S80914 S81402 S81403 S81301 S80901 S80915 S81028 S80904 S81401 S82052 S81301 S80479 S81012 S80478 S86250 Description Handle Support, Handle T-Tube Rivet 5x11 Block Hand Wheel 8x60 Spring Plate, Threaded Rivet 5x11 Base, Cart Screw 12x140 Masher M12 Wheel Bushing Spacer Rivet 5x11 Caster Washer Nut M10 Hand Grip 18 Qty.
Tank Assembly 415PLT No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Part# S81847 S81300 S83773 S81026 S82586 S82846 S82593 S82583 S82594 S82608 S83771 S82993 S83883 S81026 S81026 S83883 S82172 Description Clamp, Tank Rivet 5x24.5 Tank Screw 5x30 Adapter, Tank Gasket Deflector Inlet Cover Button Spring Bumper Handle Washer, Plastic Screw 5x30 Screw 5x30 Washer, Plastic Hook, Tank 19 Qty.
Cart Assembly 415PLT No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Part# S82053 S82607 S82173 S81979 S83725 S83751 S83694 S83835 S82557 S80904 S82607 S82980 S83752 S81026 S82967 S81050 S82974 S82627 S81006 S82559 S83797 Description Spring Spacer Lock, Plastic Screw 5x25 Clamp Shaft Handle Cap, Axle Cap, End Wheel Spacer Spacer Axle Screw 5x30 Support, Axle Screw 5x35 Washer Screw 5x40 Screw 5x20 Caster Base, Cart 20 Qty.
Tools 4 3 1 8 2 5 6 7 Item Part# Description Qty 1 2 3 4 5 6 7 7a 1 S72672 S70003 S76295 S70008 S76387 S76389 S76384 S76385 S82333 S76388 Complete Tool Kit Crevice Tool Round Brush Hose Wand, Straight Wand, Curved 16” Floor Brush 16” Floor Squeegee Replacement Squeegee Blades Adapter 1 1 1 1 2 1 1 1 2 1 21
Filters Part# S82860 S82845 S83742* S73742* S82881* S82852* S76061* S82995* S82855 T80092 T80093 Description Filter Bag, Standard Polyester Filter Bag, Standard Polyester Cartridge Filter, Paper Cartridge Filter, Polyester Cartridge Filter, HEPA Equivalent Cartridge Filter, Paper Cartridge Filter, Polyester Cartridge Filter, HEPA Equivalent Cartridge Filter Retainer Paper Filter Bags 5/pkg. Paper Filter Bags 3/pkg.
S70042 22” Front-Mounted Squeegee fits all 415/429/430 models No. Part# Description Qty.
T80020 30” Front-Mounted Squeegee fits 415/429/430 models with Polyethylene Tanks No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Not Pictured Part# BD735602 BD735601 BD7015509 BD735609 BD715508 BD735609 BD735607 BD735608 BD705201 BD705202 BD705203 BD735610 BD735609 BD735605 BD735603 T80021 Description Blade, Slotted Blade, Solid Support, Blade Nut, Nylock 1/4-20 Housing Assy. Nut, Nylock 1/4-20 Wheel, Guide Bolt, 1/4-20 x 1.75” Lifting Arm Assy. Cross Member Latch Assy.
T80054 30” Front-Mounted Squeegee fits 415PLT Plastic Tipping Tank No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Part# T80021 BD715508 BD735608 BD735607 BD735611 BD735603 BD735609 BD735605 BD735602 BD735601 BD715509 BD735603 BD735609 BD735612 BD705225R BD705225L BD705209 BD705210 BD735614 BD735612 BD705212 BD705209 BD735609 BD705229 Description Hose Assy. Housing Bolt, Guide Wheel 1/4-20 x 1.
Warranty Policy Limited Warranty IPC Eagle warrants new cleaning equipment against defects in material and workmanship under normal use and service to the original purchaser as detailed below. 3 years Subject to the conditions stated below, IPC Eagle warrants all Polyethylene Tanks to be free from defects in materials and workmanship for a 3-year period. Parts replaced or repaired are warranted for the remainder of the original warranty period.
