WET/DRY VACUUMS POLYETHYLENE, POLYPROPYLENE & STEEL MODELS: 315P 415P 429P 415S 415ST 415PLT 429ST OPERATIONS AND PARTS MANUAL IMPORTANT! READ THIS MANUAL PRIOR TO USE.
TABLE OF CONTENTS Page No. Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . .1-3 Vacuum and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . .4 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Daily Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Periodic Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. WARNING DANGER: ! ! Failure to read and observe all DANGER statements could result in severe bodily injury or death. Read and observe all DANGER statements found in your Owner’s Manual and on your machine.
! ! DANGER: Electrocution could occur if maintenance and repairs are performed on a unit that is not properly disconnected from the power source. Disconnect the power supply before attempting any maintenance or service. WARNING: Operating a machine without observing all labels, decals, etc., could result in injury or damage. Read all machine labels before attempting to operate the machine. Make sure all of the labels are attached or fastened to the machine.
120 Volt Machine Instructions For Connection To The Power Supply And The Electrical Ground This machine must be connected to the electrical ground to protect the operator from electric shock. The machine has an approved power cord with three conductors and a plug with three terminals. Connect the plug to a receptacle that has three holes and is connected to the electrical ground. The green (or green and yellow) conductor in the cord is the ground wire.
VACUUM AND ACCESSORIES A B C D E F G H I J K M N O P Motor Block On/Off Switch Float: Keeps liquid out of Motor Block Polyester Filter: Remove for use with liquids Hooks: Secure Motor Block to Tank Suction Inlet Tank 1-pc. Hose End, Bent PVC Hose, 10-ft. x 1-1/2" Flexible 1-pc PVC Wand (2) Adapter Dust Brush Crevice Tool Floor Brush, 16" Squeegee, 16" ATTENTION: The Polyester Filter must be cleaned after each use to maintain efficient suction.
OPERATION This machine is a commercial vacuum designed for wet and dry pick-up. The dual vac motors can be run together or separately as the job requires. DUAL SWITCHES Dry soil can be vacuumed directly into the tank. To empty the tank of dry soil, remove the top and dump into trash receptacle. Dual Vacuum For wet pick-up, remove polyester filter. The machine is equipped with a float shut-off. As the tank is filled to capacity, a float rises and seals the vac intake, causing loss of vacuum.
PERIODIC MAINTENANCE (Every six to twelve months): 1. Check filter for wear, replace dirt saturated filters that do not respond to normal cleaning. 2. Inspect gasket seals and replace those which have begun to leak. 3. Examine carbon motor brushes and commutator. Replace both carbon brushes when either is less than 3/8" long. (PN S8TOEG845) SERVICING THE FILTER The filter is accessed by lifting the head assembly off the tank.
SERVICING THE VAC MOTOR CARBON BRUSH REPLACEMENT 1. Disconnect power cord from power source. 2. To access the vac motor, remove the screws that attach the main cover to the head assembly and set the cover to one side. 3. Remove the motor cover by removing two screws. See Figure 1 4. Remove the wire terminal from carbon brush housing. See Figure 2 5. Remove the carbon brush assembly by removing the 2 screws that attach it to the vac motor. See Figure 3 6. Inspect armature commutator.
315 VACUUM MOTOR ASSEMBLY No. Part Num. Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. S80326 S81006 S81006 S80140 S81006 S82992 S81152 S80138 S81122 S81006 S80139 S83937 S81146 S83969 S81006 S81005 S83900 S83608AU S83901 S81024 S81064 S81120S S83901 S83866 S80120 Switch, ON/OFF Screw, 5 x 20 Screw, 5 x 20 Terminal Block Screw, 5 x 20 Handle, Lift Qty.
415 VACUUM MOTOR ASSEMBLY No. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. Part Num.
415P TANK ASSEMBLY No. Part Num. Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. S82615 S82558 S82637 S81026 S82584 S82846 S82593 S82652A S81300 S81847 S81050 S83883 S81072 S81860 S81302 S82559 S82680 S82556 Complete Tank Handle Tank Screw, 5x30 Retainer, Tank Gasket Deflector Adapter, Hose Rivet, 5 x 24.5 Clamp, Tank Screw, 5 x 35 Plastic Washer Support, Handle Support, Handle Rivet, 5 x 19 Caster Screw, 4 x 15 Support, Axle Qty. No. Part Num.
415ST TANK ASSEMBLY No. Part Num. Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. S82993 S81847 S81302 S83629 S83883 S83253 S81026 S82586 S82846 S82593 S82583 S82594 Handle Clamp, Tank Rivet, 5 x 19 Screw, 5 x 25 Washer Tank – Steel Screw, 5 x 30 Adapter, Tank Gasket Deflector Adapter, Hose Button Qty. No. Part Num. Description 2 2 4 4 4 1 4 1 1 1 1 1 13. 14. 15. 16. 17. 18. 19. 20. 21.
415S TANK ASSEMBLY No. Part Num. Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. S82993 S81847 S81302 S83629 S83883 S80476 S81026 S82586 S82846 S82593 S82583 S82594 S82608 Handle Clamp, Tank Rivet, 5 x 19 Screw, 5 x 25 Washer Tank Screw, 5 x 30 Adapter, Tank Gasket Deflector Adapter, Hose Button Spring Qty. 2 2 4 4 4 1 4 1 1 1 1 1 415S CART 12 No. Part Num. Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20.
415PLT TANK ASSEMBLY No. Part Num. Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. S81847 S81300 S83773 S81026 S82586 S82846 S82593 S82583 S82594 S82608 S83771 S82993 Clamp, Tank Rivet, 5 x 24.5 Tank Screw, 5 x 30 Adapter, Tank Gasket Deflector, Tank Adapter, Hose Button, Hose Spring Bumper Handle Qty. No. Part Num. Description 2 4 1 4 1 1 1 1 1 1 1 1 13. 14. 15. 16. 17. S83883 S81026 S81026 S83883 S82172 Washer, Plastic Screw, 5 x 30 Screw, 5 x 30 Washer, Plastic Hook, Tank Qty.
S70042 FRONT-MOUNTED SQUEEGEE No. Part Num. Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. S82164 S82187 S82163 S83115 S82189 S81033 S81732 S86137 S82245 S86138 S81034 Handwheel, M8 x 45 Small Block, Fixed Handwheel, M6 x 25 Plate, Adjustment Driver Pivot Nut, M8 Adjustment Knob Spring, Ø40 Rear Squeegee Wheel, AIF, Ø40 Washer, Plain, M8 Qty. No. Part Num. Description 1 1 1 1 1 2 2 2 1 2 1 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22.
Warranty Policy Limited Warranty Eagle Power Products (EPP) warrants new cleaning equipment against defects in material and workmanship under normal use and service to the original purchaser as detailed below. 10 Years Subject to the conditions stated below, EPP warrants polyethylene tanks and housings to be free from defects in materials and workmanship for a period of ten years.
