MSDS

ManualsBrandsEagle ManualsPaint1-gal. Patina Concrete Acid Stain

Material Data Safety Sheet

ACID STAINS Date: 8/24/2011

Section I- Chemical Product and Company Identification

Product/Chemical Name: Deep Stain

CAS Number: Mixture

Manufacturer: Eagle IFP. Co. Phone: 615-872-2710

505 Cave Rd. Fax: 615-872-9052

Nashville, TN 37210 www.eaglesealer.com

EMERGENCY TELEPHONE NUMBER: In the event of an emergency call INFOTRAC 1-800-535-5035

****Emergency Overview****

ACID STAIN

• Has a chlorine odor

• Is corrosive (D002)

• Is non-combustible

Section II - Composition / Information on Ingredients

Ingredient Name CAS Number % Wt

Hydrochloric Acid 7647-01-0 <25

Manganese Chloride 13446-34-9 <25

Sodium dichromate dihydrate 7789-12-0 <25

Ferric chloride, hexahydrate 10025-77-1 <25

Copper (II) Chloride Dihydrate 10125-13-0 <25

OSHA TLV

ACGIH TLV

Hydrochloric acid: 5 ppm. 5 ppm

Manganese Chloride 5 mg/m

0.2 mg/m

Sodium Dichromate 0.005 mg/m

0.05 mg/m

Ferric Chloride 1 mg/m

1 mg/m

Copper (II) Chloride 1 mg/m

1 mg/m

Section III – Physical and Chemical Properties

Physical Appearance: colored liquid Water Solubility: 100%

Odor: Chlorine odor Material VOC: 0 g/L

Vapor Pressure: H2O Boiling Point: 215 °F (102 °C)

Vapor Density: Equal to water Freezing/Melting Point: Not Determined

Specific Gravity (H20=1, at 4 °C): 1.0-2.0 pH: <4

Page 1 of 4

HMIS

Health 3 Serious

Flammability 0 Minimal

Reactivity 2 Moderate

Precaution: G

Summary of content (4 pages)

PAGE 1
Material Data Safety Sheet ACID STAINS Date: 8/24/2011 Section I- Chemical Product and Company Identification HMIS Product/Chemical Name: Deep Stain CAS Number: Mixture Manufacturer: Eagle IFP. Co. 505 Cave Rd. Nashville, TN 37210 Phone: 615-872-2710 Fax: 615-872-9052 www.eaglesealer.
PAGE 2
Section IV – Fire-Fighting Measures Flash Point: N/A LEL: Not Determined UEL: Not Determined Flammability: Non-flammable Extinguishing Media: Dry chemical, foam or CO2 Unusual Fire or Explosion Hazards: Hydrogen gas may form explosive mixture in the air. At high temperatures toxic corrosive fumes of anhydrous gas may be emitted. Hazardous Combustion Products: hydrogen chloride and oxides of copper Fire-Fighting Instructions: Do not release runoff from fire control methods to sewers or waterways.
PAGE 3
After first aid, get appropriate in-plant, paramedic, or community medical support. Spill/Leak Procedures Small Spills: Spills may be absorbed using cement powder or fly ash and shoveled into containers. Neutralize spills with lime, sodium bicarbonate or crushed limestone and prevent runoff. Notify proper authorities if runoff should occur. Large Spill Containment: For large spills, dike far ahead of liquid spill for later disposal. Do not release into sewers or waterways.
PAGE 4
Section IX – Special Precautions and Comments Handling Precautions: Keep away from all ignition sources (heat, flame, sparks and strong oxidizers). Use only in well ventilated areas. Storage Requirements: Store in safety containers. DOT: Corrosive liquid, acidic, inorganic, n.o.s. (Hydrochloric acid), 8, UN3264, PGIII Disclaimer: The information contained herein is based on data considered accurate.