Datasheet

Single-LED, T1 3/4 MG
Illumination colour Operating voltage Operation current Lumi. Intensity Dom. Wavelength Part No.
Wiring
diagram
Red 6 V DC +10% 15 mA ±15 % 350 mcd 630 nm 10-2J06.3142 55
12 V AC/DC +10% 7 - 14 mA ±15 % 330 mcd 630 nm 10-2J09.1062 55
24 V AC/DC +10% 7 - 14 mA ±15 % 330 mcd 630 nm 10-2J12.1062 55
28 V AC/DC +10% 7 - 14 mA ±15 % 330 mcd 630 nm 10-2J13.1062 55
48 V AC/DC +10% 4 - 8 mA ±15 % 200 mcd 630 nm 10-2J19.1042 55
Yellow 6 V DC +10% 15 mA ±15 % 300 mcd 587 nm 10-2J06.3144 55
12 V AC/DC +10% 7 - 14 mA ±15 % 280 mcd 587 nm 10-2J09.1064 55
24 V AC/DC +10% 7 - 14 mA ±15 % 280 mcd 587 nm 10-2J12.1064 55
28 V AC/DC +10% 7 - 14 mA ±15 % 280 mcd 587 nm 10-2J13.1064 55
48 V AC/DC +10% 4 - 8 mA ±15 % 180 mcd 587 nm 10-2J19.1044 55
Green 6 V DC +10% 7 mA ±15 % 1050 mcd 525 nm 10-2J06.3145 55
12 V AC/DC +10% 4 - 7 mA ±15 % 1050 mcd 525 nm 10-2J09.1065 55
24 V AC/DC +10% 4 - 7 mA ±15 % 1050 mcd 525 nm 10-2J12.1065 55
28 V AC/DC +10% 4 - 7 mA ±15 % 1050 mcd 525 nm 10-2J13.1065 55
48 V AC/DC +10% 2 - 4 mA ±15 % 600 mcd 525 nm 10-2J19.1045 55
Blue 6 V DC +10% 15 mA ±15 % 680 mcd 470 nm 10-2J06.3146 55
12 V AC/DC +10% 4 - 14 mA ±15 % 650 mcd 470 nm 10-2J09.1066 55
24 V AC/DC +10% 7 - 14 mA ±15 % 650 mcd 470 nm 10-2J12.1066 55
28 V AC/DC +10% 7 - 14 mA ±15 % 650 mcd 470 nm 10-2J13.1066 55
48 V AC/DC +10% 4 - 8 mA ±15 % 400 mcd 470 nm 10-2J19.1046 55
White 6 V DC +10% 6 mA ±15 % 900 mcd x: 0.31 / y: 0.32 nm 10-2J06.3149 55
12 V AC/DC +10% 3 - 6 mA ±15 % 900 mcd x: 0.31 / y: 0.32 nm 10-2J09.1069 55
24 V AC/DC +10% 2,5 - 5 mA ±15 % 750 mcd x: 0.31 / y: 0.32 nm 10-2J12.1069 55
28 V AC/DC +10% 2,5 - 5 mA ±15 % 750 mcd x: 0.31 / y: 0.32 nm 10-2J13.1069 55
48 V AC/DC +10% 2 - 4 mA ±15 % 600 mcd x: 0.31 / y: 0.32 nm 10-2J19.1049 55
Red / Green 24 V AC/DC +10% 15/14 mA ±15 % 600/630 mcd 625 / 525 nm 10-A312.314A 171
Additional information
• Due to high surface temperatures, the series resistor must not be soldered directly to the terminals of the
equipment (use a terminal plate)
• When using AC/DC types with AC operation, slight ickering can occur
• The luminous intensity stated is for when used with DC
• Electricalandopticaldataaremeasuredat25°C
• The specied versions are built with a protection diode (halve wave rectier) in series and the LED
• Luminosity and wave length variations caused by LED manufacturing processes may cause slight diffe-
rences regarding the illumination. The customer has to decide what resistor shall be used to the LED
• Where supply voltages are over 48 V, a voltage-reduction element (external protective series resistor)
must be used.
Dimensions [mm]
Components
eao.com § 01/2019
660
51
01
02
03
04
09
14
17
18
19
22
31
41
45
51
56
57
61
70
71
82
84
92
96
16 max.
Ø6.1 max.