N0150 05/05.qxd 27/5/05 10:28 am Page 1 HV7000A / HV7000P OPERATING INSTRUCTIONS Thank you for purchasing the Earlex Spray Port. This is a highly versatile spray kit and can be used on a variety of applications. BEFORE USE - PLEASE READ THE SAFETY & OPERATING INSTRUCTIONS.
N0150 05/05.qxd 27/5/05 10:28 am Page 2 SAFETY INSTRUCTIONS WARNING! FIRE AND EXPLOSION HAZARD. NEVER, under any circumstances, point the spray CAUTION: TO REDUCE THE RISK OF gun at another person or animal. In the event of ELECTRIC SHOCK OR INJURY, USE injury occurring, seek expert medical advice INDOORS ONLY. The substances used with this spray applicator (paint, thinners etc) may contain hazardous, harmful, explosive or corrosive materials.
N0150 05/05.qxd 27/5/05 10:28 am Page 3 INTRODUCTION The Earlex HV7000 “Spray Port” is an industrially rated, portable, paint spraying system and is intended for use by professionals. HVLP stands for High Volume, Low Pressure. This is a type of spraying that allows you to spray extremely accurately but without all the overspray that occurs with high pressure tank equipment.
N0150 05/05.qxd 27/5/05 10:28 am Page 4 IDEAL VISCOSITY Water based paints and emulsions Oil based paints Wood preservatives Primers 45 - 60 seconds Varnishes Aluminium paints Wood stains Cellulose 45 - 50 seconds No dilution 45 - 50 seconds Manufacturers Manufacturers Manufacturers Manufacturers ratio ratio ratio ratio This spray applicator can be used with products having a viscosity ranging from 10 to a maximum of 60 seconds. Dip the viscosity cup into the material and fill up.
N0150 05/05.qxd 27/5/05 10:28 am Page 5 SPRAY PATTERNS Fig.4 The spray applicator has 3 different spray patterns – Horizontal, Vertical and Round (Fig.4) The horizontal and vertical are recommended for large surfaces. Vertical Jet Horizontal Jet Round Jet The round spray is used for small objects or for areas - such as corners – that are difficult to reach.
N0150 05/05.qxd 27/5/05 10:28 am Page 6 CLEANING INSTRUCTIONS Remember to disconnect the unit from the mains power when undertaking any cleaning of the Spray Port. THE SPRAY APPLICATOR MUST BE THOROUGHLY CLEANED IMMEDIATELY AFTER USE. IF THE PAINT DRIES INSIDE THE GUN, CLEANING WILL BECOME MUCH MORE DIFFICULT AND MAY RENDER THE GUN INOPERABLE. THIS IS NOT COVERED BY WARRANTY. The spray applicator is the same as a paintbrush, if it is not cleaned it will go hard and can become useless.
N0150 05/05.qxd 27/5/05 10:28 am Page 7 MAINTENANCE SPRAY APPLICATOR Keep the internal workings of the spray applicator clean. The spray applicator should be thoroughly cleaned after each use. Follow the cleaning instructions on page 6 with reference to the drawings on page 8 Check the needle and fluid tip on a regular basis for excessive wear, and replace as necessary. See the cleaning instructions for the correct procedure for removing these parts.
N0150 05/05.qxd 27/5/05 10:28 am Page 8 SPRAY APPLICATOR SPARE PARTS DRAWINGS 8 TYPE P Key Description No. 01. Air Cap Ring 02. Air Cap 03. Spray Direction Plate 04. 0.08” (2.0mm) Fluid Tip 05. Fluid Tip Seal 06. 0.08” (2.0mm) Fluid Needle 07. Spring 08. Fluid Adjusting Screw 09. Gland Nut 10. Gland 11. Paint Feed Tube 12. Paint Container Seal 13. Paint Container (Clear) 14. Hose Assembly 15.
N0150 05/05.qxd 27/5/05 10:28 am Page 9 TURBINE UNIT & CARRIER STAND PARTS DRAWINGS 1 2 Power IN (IEC Connector) Circuit Breaker 3 4 5 6 Mains Switch (120V) 7 SPARE PARTS LIST 1. 2. 3. 4. Hose Connector Assembly (29ft 10”) N0099 Semi Hose Reel Moulding N0116 Carrier Frame Assembly N0162 Filter Media x 2 N0087 5. Main Frame Assembly 6. Power Cord 7.
N0150 05/05.
N0150 05/05.
N0150 05/05.qxd 27/5/05 10:28 am Page 12 Copyright & Design Right Reserved © 2005 Design Registration UK 3015591 WARRANTY This product is guaranteed for a period of 12 months for ordinary use and 6 months for hire purposes or where the unit is lent to other users.The guarantee is against faulty manufacture and materials.
