EARTHQUAKE SOUND PowerHouse Series Amplifiers Owners Manual MODELS: PH800W/2 PH1000W/2 PH2200W/4 PH2000W/D1 PH2000W/D1.1 PH5000W/D1 PH10000W/D1 PH20000W/D1 The Sound That Will Move You. Earthquake Sound reserves the right to amend details of the specifications without notice. Copyright © Earthquake Sound Corporation Earthquake Sound Corporation • 2727 McCone Avenue Hayward CA, 94545 • Phone: 510732-1000 Fax: 510-732-1095 Sound That Will Move You.
WARRANTY Table Of Contents Cautions and Advisories Page 2 Warranty Page 3 - 4 Specifications Page 5 PH800W/2 Page 6 - 7 PH1000W/2 Page 8 - 9 PH2200W/4 Page 10 - 11 PH2000W/D1 Page 12 - 13 PH2000W/D1.1 Page 12 - 13 PH5000W/D1 Page 14 - 15 PH10000W/D1 Page 16 - 18 Installation Example Page 19 Five (5) year limited warranty; PH800W/2, PH1000W/2, PH2200W/4, PH2000W/D and PH2000W/D1.
4 Specifications Are Subject To Change Without Notice NOTE: In some cases when the amplifier is on “AUTO ON” mode, if your system generates noise through the RCA wire and therefore waking up the amplifier, you may want to switch your amplifier installation to the “REMOTE ON” mode (must use the turn on wire). NOTE: The RCA outputs must be inserted in CH1/2 for the amplifier to detect any incoming signal.
PH800W/2 VTEK-MC5 Tweeter Protect 20Hz 5kHz Filter Setting Bypass Crossover Frequency 1- 2- 1+ 2+ Power 1 1 Gain Speaker Level Input VTEK-MC5 Tweeter Bypass 2 2 Rca level input Output VTEK-MC5 Midrange VTEK-MC5 Midrange Crossed RCA level outputs, can be used to feed other amplifiers in the system. The gain knob is not a volume control. It is designed to match the input level of the amp to the output level of the source unit.
PH1000W/2 +18dB boost @ 45Hz designed to shape/ boost the response curve in a low-pass mode application. +12dB boost @ 12kHz essential boost for high-pass amplifier applications 3-way switch runs the amp in low-pass, full-range or high-pass mode. RCA level inputs, with a range of 0.2V to 5V. RMS. FC6.2 Tweeter 3-way switch feeds RCA outputs a low-pass fullrange or high pass signal. The PH1000W/2 is designed to operate in stereo or mono mode.
PH2200W/4 3-way switch feeds, RCA outputs 3/4 a full range, high-pass or lowpass signal. FC6.2 Midrange FC6.2 Tweeter FC6.2 Midrange FC6.2 Tweeter Remote ON Auto ON Signal Sensor: Remote ON/Auto ON feature (see page 5). 3-way switch for each block runs CH1/2 or CH3/4 in low -pass, full-range or highpass mode.
PH2000W/D1 PH2000W/D1.1 * Test the alternator output. Factory alternators will produce 60-80 amperes at best. Wear and heat will reduce the output by 40%. * Alternator ground (-) must be reinforced, use 4-gauge cable instead of the factory 8-gauge. Variable 10dB boost at 40Hz. Perfect tool for high SPL scores. * Alternator positive (+) to battery (+) must be reinforced. Use 4-gauge cables. * Check your battery condition. Batteries degrade after a while.
PH5000W/D1 • Test the alternator output. Factory alternator will produce 60 to 80 amperes at best. Wear and heat will reduce the output by 40%. SIGNAL SENSOR: This feature allows you to eliminate the use of a remote wire to turn on your amplifier. In AUTO mode the amp will automatically detect an incoming signal when the stereo is turned on. If the amplifier does not detect a signal within 20min. it will automatically shutdown.
PH10000W/D1 High Level speaker input RCA, Low Level input RCA, Low Level out The low-pass filter, blocks unwanted high frequencies to allow cleaner low-frequencies. This switch will line match the voltage of your head unit, which will deliver high sound quality and performance. "RCA level" audio signal needed to clip the input stage (bass boost at minimum) Peaks or dips occur at about 40Hz — around the frequency of a low bass guitar note. Use this control to correct that peak or dip.
18 GND 0 BAT Specifications Are Subject To Change Without Notice POWER REM GND BAT Audio signal 180 Phase Shift 2 Ohms Minimum 10000 watts rated output REM Master Amplifier Head Unit / audio source 0 REM GND Slave Amplifier BAT • Set master amp to 0 • Set slave amp phase to 180 • Set gains equal on both master & slave amplifiers • Set th bass boosts and filters equal on both amps 180 Phase Shift PH10000W/D1 - Linking Installation Example www.earthquakesound.