Operator's Manual Original Operating Instructions VECTOR™ Compact Tiller GAS/OIL RATIO Product #’s: 26750 14318 (CE) Get parts online at www.getearthquake.com 50:1 P/N: 13278 ECN: 9843 REV5: 04/10/13 © 2013 Ardisam, Inc.
Operator's Manual VECTOR™ Compact Tiller INTRODUCTION Congratulations on your investment in quality. Thank you for purchasing the VECTOR™ Compact Tiller from Earthquake™. We have worked to ensure that this tiller meets the highest standards for usability and durability. With proper care, your tiller will provide many years of service. Please read this entire manual before installation and use.
Operator's Manual VECTOR™ Compact Tiller WARNINGS AND SAFETY PRECAUTIONS OPERATOR'S RESPONSIBILITY Accurate assembly and safe and effective use of the machine is the operator's responsibility. • Read and follow all safety instructions. • Carefully follow all assembly instructions. • Maintain the machine according to directions and schedule included in this Earthquake operator’s manual. • Ensure that anyone who uses the machine is familiar with all controls and safety precautions.
Operator's Manual VECTOR™ Compact Tiller GENERAL SAFETY RULES • Read, understand, and follow all instructions on the machine and in the manual(s). Be thoroughly familiar with the controls and the proper use of the machine before starting. • Use this equipment for its intended purpose only. • Familiarize yourself with all of the safety and operating decals on this equipment and on any of its attachments or accessories. • Do not put hands or feet near or under rotating parts.
Operator's Manual VECTOR™ Compact Tiller • Tines rotate when the tiller is engaged; tines rotate when the drive safety control lever is pulled down. Releasing the drive safety control lever to the neutral position stops the tines. • Do not overload the machine capacity by attempting to till too deep at too fast of a rate. • Be careful when tilling in hard ground. The tines may catch in the ground and propel the tiller forward. If this occurs, let go of the handlebars and do not restrain the machine.
Operator's Manual VECTOR™ Compact Tiller • Always wipe up excess (spilled) fuel from engine before starting. Clean up spilled fuel immediately. If fuel is spilled, do not start the engine but move product and fuel container from area. Clean up spilled fuel and allow to evaporate and dry after wiping and before starting. CHILDREN AND BYSTANDERS Tragic accidents can occur if the operator is not alert to the presence of children and/or bystanders.
Operator's Manual VECTOR™ Compact Tiller SAFETY DECALS This rototiller unit has been designed and manufactured to provide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing.
Operator's Manual VECTOR™ Compact Tiller UNPACKING AND ASSEMBLY UNPACKING AND ASSEMBLING YOUR TILLER 1. Open top of carton and remove handlebar assembly. 2. Parts bag for VECTOR tiller contains: 2- Bolts M8 x 1.25 x 20 Hex Head 6- Bolts M8 x 1.25 x 25 Hex Head 6- Washers M8 8.4mm x 24mm x 2.2mm 6- Nuts M8 x 1.25 IMPORTANT THE RIGHT AND LEFT SIDES OF YOUR ROTOTILLER ARE DETERMINED FROM THE OPERATING POSITION AS YOU FACE THE DIRECTION OF FORWARD TRAVEL. ENGINE IS SHIPPED FROM FACTORY WITHOUT OIL.
Operator's Manual VECTOR™ Compact Tiller 5. Assemble tine shield extensions using six (6) M6 bolts and six (6) nylock nuts. SEE FIGURE 4 6. Assemble tines to unit. Sharp edges of tines will be away from the operator at the top or facedown at front of machine. Fasten outer tines to the inner tines using the 8mm x 40mm lock pins already affixed to the inner tines.
Operator's Manual VECTOR™ Compact Tiller FEATURES drive safety control lever adjustable forward cable adjustable handlebar height adjustable depth regulator transport wheels tines SPECIFICATIONS SOUND AND VIBRATION LEVELS ENGINE DISPLACEMENT 99cc TILLING WIDTH 11 in., 16 in., 21 in. TILLING DEPTH 11 in.
Operator's Manual VECTOR™ Compact Tiller OPERATION CONTROLS DRIVE SAFETY CONTROL LEVER Engage tines into forward, releasing returns machine to neutral. Pulling down on drive safety control lever engages the tines. Releasing the drive safety control lever to a neutral position disengages the tines. BELT TENSION ADJUSTMENT Proper belt tension is critical to good performance. After 1/2 hour of operation, all cables may have to be adjusted due to initial stretch.
Operator's Manual VECTOR™ Compact Tiller PRE-START INSPECTION 1. Make sure all safety guards are in place and all nuts and bolts are secure. 2. Check oil level in engine crankcase. See your engine manual for procedure and specifications. 3. Inspect air cleaner for cleanliness. See your engine manual for procedure. 4. Check the fuel supply. Fill the fuel tank no closer than 1 inch from top of tank to provide space for expansion. See your engine manual for fuel recommendations. 5.
Operator's Manual VECTOR™ Compact Tiller OPERATING SPEED For normal tilling, set the throttle lever to FAST. SHUTTING DOWN To stop the engine at any time, turn the On/Off switch to the OFF position. To stop tines at any time, release the drive safety control lever to the neutral position. TILLING 1. Adjust the depth regulator lever to desired tilling depth. NOTE: Raise depth regulator lever up one hole at a time, testing tiller operation after each raise.
Operator's Manual VECTOR™ Compact Tiller SERVICING THE ROTOTILLER The following information will help you make the necessary checks and perform the procedures required to follow the normal care recommendations made for your rototiller unit. If you prefer, your local authorized dealer can make these checks and perform the required procedures for you. WARNING C H E C K F O RWA R D B E LT T E N S I O N R E G U L A R LY. TOO MUCH OR TOO LITTLE TENSION WILL CAUSE PREMATURE BELT FAILURE.
Operator's Manual VECTOR™ Compact Tiller ENGINE MAINTENANCE Refer to the engine manual included in your parts packet for information on engine maintenance. Your engine manual provides detailed information and a maintenance schedule for performing the following tasks: 1. Check oil level before each use or after every 8 hours of operation. 2. Change oil after first 5-8 hours of operation. Change oil while engine is warm. Refill with new oil of recommended grade. 4.
Operator's Manual VECTOR™ Compact Tiller TROUBLESHOOTING AND REPAIR WARNING TROUBLESHOOTING GUIDE PRACTICE SAFETY AT ALL TIMES. ENGINE MUST BE TURNED OFF AND ALLOWED TO COOL, AND SPARK PLUG WIRE MUST BE DISCONNECTED AND SECURED BEFORE ATTEMPTING ANY MAINTENANCE OR REPAIR. FAILURE TO COMPLY WITH THIS SAFETY REQUIREMENT CAN RESULT IN SERIOUS PERSONAL INJURY TO YOU OR BYSTANDERS.
Operator's Manual VECTOR™ Compact Tiller PARTS BREAKDOWN HANDLEBAR ASSEMBLY PARTS EXPLOSION AND PARTS LIST 7 8 9 6 21 5 18 10 12 11 13 19 17 16 15 14 22 1 2 3 4 20 REF. NO. PART # 3 2 1 DESCRIPTION QTY. 1 18135 BOLT M8 X 1.25 X 25 SFH GR8.8 ZN 6 2 3245 WASHER M8 8.4MM X 24MM X 2.2MM ZN 6 3 64132 NUT M8 X 1.
Operator's Manual VECTOR™ Compact Tiller 3 11 22 21 7 30 10 9 26 27 6 5 10 15 8 2 29 23 28 11 1 31 11 4 10 26 27 25 13 14 12 16 18 19 20 17 24 ENGINE ASSEMBLY PARTS EXPLOSION 18 Check for parts online at www.getearthquake.
Operator's Manual VECTOR™ Compact Tiller ENGINE ASSEMBLY PARTS LIST REF. NO. PART # DESCRIPTION QTY. 1 53617 ARM FORWARD REAR TINE 1 2 13364 FORWARD IDLER PULLEY 10MM 1 3 332033 BOLT M10 X 1.5 X 50 HHCS 1 4 W1265V0915 BOLT M8 X 25 HHCS 2 5 W1265V0904 BOLT M8 X 1.25 X 20 HHCS 2 6 18008 BUSHING 16.4MM X 22MM X 21.5MM 1 7 38397 KEY 3/16IN X 1.75IN 1 8 3235 NUT M10 X 1.5 HTPLK 1 9 803 WASHER 5/16"ID X 1-1/2"OD FLAT 16 GA.
Operator's Manual VECTOR™ Compact Tiller CHASSIS ASSEMBLY PARTS EXPLOSION AND PARTS LIST 4 5 9 21 18 8 13 11 1 6 7 10 7 13 2 21 20 8 11 16 11 8 14 22 23 17 8 19 3 15 12 REF. NO. PART # DESCRIPTION 1 18004 WELDMENT VECTOR FRAME 2 13366 LOCK PIN WIRE BALE 3 92776 4 18010 QTY. REF. NO. PART # DESCRIPTION QTY. 1 13 18103 BOLT M6 X 1.0 X 40 HH GR 8.8 ZN 4 1 14 331052 NUT M12 X 1.75 HH NYLCK GR8.8 ZN 2 BOLT M6 X 1.0 X 20 HHCS GR8.8 ZN 2 15 W1200116 WASHER M6 X 1.
Operator's Manual VECTOR™ Compact Tiller TRANSMISSION ASSEMBLY PARTS EXPLOSION AND PARTS LIST 20 22 24 29 13 11 10 18 3 19 2 15 17 1 5 26 9 8 27 27 7 12 26 24 21 6 14 28 16 4 28 15 14 6 25 23 22 23 25 REF. NO. PART # DESCRIPTION 1 13610 WORM DRIVESHAFT 20MM OD 2 8924 RING RETAINING EXTERNAL 3/4 INCH QTY. REF. NO. PART # DESCRIPTION QTY. 1 16 13615 GEAR BRASS 25MM ID 6MM KEY FT 1 1 17 13590 BUSHING 26MM X 20.22MM X 6.
Operator's Manual VECTOR™ Compact Tiller FRONT TINE ROTOTILLERS Warranty Terms and Conditions PRODUCT WARRANTY: 1-YEAR LIMITED WARRANTY Ardisam, Inc., a manufacturing company, warrants this EARTHQUAKE™ VECTOR™ COMPACT TILLER to be free from defects in the material or workmanship for a period of one year from the date of purchase. During the one-year warranty of this product, Ardisam will furnish, at their discretion, parts and labor to correct any defect caused by faulty material or workmanship.
Operator's Manual VECTOR™ Compact Tiller Check for parts online at www.getearthquake.
Earthquake®, Division of Ardisam, Inc. 1160 8th Avenue, PO Box 666 Cumberland, WI 54829 800-345-6007 | Fax 715-822-2223 E-mail: info@ardisam.com All weights, specifications and features are approximate and are subject to change without notice. Due to continuous product improvements, product images may not be exact. Items used for props not included. Some assembly may be required. Check for parts online at www.getearthquake.
