Operator's Manual Original Operating Instructions Front Tine Rototiller 3310V Get parts online at www.GetEarthquake.com OM3310v Rev. 02/21/11 © 2011 Ardisam, Inc.
Operator's Manual Front Tine Tiller 3310V INTRODUCTION Thank You . . . for purchasing an Earthquake® forward rotating front tine rototiller from Ardisam, Inc. We have worked to ensure that this front tine rototiller meets high standards for usability and durability. With proper care, your rototiller will provide many years of service. Please take the time to read this manual carefully to learn how to correctly operate and maintain your rototiller.
Operator's Manual Front Tine Tiller 3310V SAFETY OWNER’S RESPONSIBILITY Accurate assembly and safe and effective use of the rototiller is the owner’s responsibility. • Read and follow all safety instructions. • Carefully follow all assembly instructions. • Maintain the tiller according to directions and schedule included in this Earthquake operator’s manual. • Ensure that anyone who uses the tiller is familiar with all controls and safety precautions.
Operator's Manual Front Tine Tiller 3310V c. Fill fuel tank outdoors with extreme care. Never fill fuel tank indoors. important d. Replace gasoline cap securely and clean up spilled fuel before restarting. • The right and left sides of your rototiller are determined from the operating position as you face the direction of forward travel. Engine is shipped from factory without oil. You must add engine oil before starting engine. Never attempt to make any adjustments while the engine is running.
Operator's Manual Front Tine Tiller 3310V SAFETY DECALS This rototiller unit has been designed and manufactured to provide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing.
Operator's Manual Front Tine Tiller 3310V Unpacking and Assembly Unpacking and Assembling Your Tiller 1. Open top of carton and remove handlebar assembly. 2. Parts bag for 3310V contains: 2- M8 x 55 screws 2- hand knobs 2- 10 x 50 shaft pins 6- M6 x 12 outer hex flange bolts 6- M6 Locknuts 1-depth regulator lever 3. a. b. c. d. Cut open top of carton and remove machine: Assemble top handlebar over lower loop. Put M8 x 55 screws through both holes from inside out.
Operator's Manual Front Tine Tiller 3310V Features (3310V) drive safety control lever throttle control lever adjustable forward cable adjustable handlebar height adjustable depth regulator lever adjustable height transport wheels front safety belt cover replaceable bolo tines Transport Position Check for parts online at www.getearthquake.
Operator's Manual Front Tine Tiller 3310V Controls Caution Drive SAFETY Control Lever Engage tines into forward, releasing returns machine to neutral. Pulling down on drive safety control lever engages the tines. Releasing the drive safety control lever disengages the tines to a neutral position. BELT TENSION ADJUSTMENT Proper belt tension is critical to good performance. After 1/2 hour of operation, all cables may have to be adjusted due to initial stretch.
Operator's Manual Front Tine Tiller 3310V Operation Important PRE-START Inspection 1. Make sure all safety guards are in place and all nuts and bolts are secure. 2. Check oil level in engine crankcase. See your engine manual for procedure and specifications. 3. Inspect air cleaner for cleanliness. See your engine manual for procedure. 4. Check the fuel supply. Fill the fuel tank no closer than 1 inch from top of tank to provide space for expansion. See your engine manual for fuel recommendations. 5.
Operator's Manual Front Tine Tiller 3310V Operating Speed Danger For normal tilling, set the throttle lever to “fast”. SHUTTING DOWN E ngine a nd surrounding pa rts become extremely hot during normal use and will cause serious burn injuries if touched before the engine has cooled. To stop the engine at any time, move throttle control to the stop position. To stop tines at any time, release the drive safety control lever to the neutral position.
Operator's Manual Front Tine Tiller 3310V SERVICING THE ROTOTILLER The following information will help you make the necessary checks and perform the procedures required to follow the normal care recommendations made for your rototiller unit. If you prefer, your local authorized dealer can make these checks and perform the required procedures for you. Check Belt Tension Belt tension may decrease over time.
Operator's Manual Front Tine Tiller 3310V Lubrication Proper lubrication of moving mechanical parts is critical for proper care and maintenance. Oil the moving parts using a 30 weight oil. check tiller transmission grease NOTE: Tiller transmission is shipped from factory with the proper amount of grease. (Suggested grease ML365) To add grease, remove both high and low grease ports. Inject grease in bottom until you see some at the top hole, transmission is now full. see figure 9.
Operator's Manual Front Tine Tiller 3310V Troubleshooting and Repair Warning Troubleshooting Guide Practice safety at all times. Engine must be turned off and allowed to cool, and spark plug wire must be disconnected and secured before attempting any maintenance or repair. Failure to comply with this safety requirement can result in serious personal injury to you or bystanders.
Operator's Manual Front Tine Tiller 3310V 3310V Handlebar parts 11 14 10 13 5 8 15 9 6 3 7 12 1 2 4 REF. NO. PART # DESCRIPTION 1 331039 FLAT WASHER 8 2 331047 3 REF. NO. PART # DESCRIPTION 2 8 331020 CLUTCH LEVER 1 HANDLE KNOB 2 9 331081 SPRING 1 331046 HANDLE ASSEMBLY 1 10 331019 CLUTCH HANDLEBAR ASSEMBLY 1 4 331099 SCREW, M8X55 2 11 331005 B PIN, 2.
3 53 24 51 52 49 50 57 42 63 56 48 24 58 47 42 Check for parts online at www.getearthquake.
Operator's Manual Front Tine Tiller 3310V 3310V motor mount & Hood parts QTY. REF. NO. PART # DESCRIPTION QTY. 35 331002 Adjustable seat 1 36 331095 Wheel seat 1 37 331052 Locknut M12 2 38 331035 Flat washer 10 2 39 331058 Outer Hex bolt M10 x 25 2 REF. NO.
Operator's Manual Front Tine Tiller 3310V tine & transmission PARTS 34 35 1 2 3 4 5 6 7 33 32 8 9 10 12 13 15 16 11 17 18 14 20 19 31 21 17 16 15 23 22 24 PART NUMBER 331110--COMPLETE TRANSMISSION 25 8 26 7 6 4 28 27 QTY 29 KEY# DESCRIPTION 4 OUTPUT SHAFT BUSHING 2 5 SPRING PIN 6 X 28 2 6 OUTER HEX FLANGE BOLT M6 X 12 12 7 OIL SEAL CAP 2 8 FRAMEWORK OIL SEAL 25 X 40 X 7 2 9 OUTER HEX FLANGE BOLT M6 X 25 5 PARTS AVAILABLE SEPARATELY REF. NO. PART # DESCRIPTION QTY.
Operator's Manual Front Tine Tiller 3310V FRONT TINE ROTOTILLERS 1-YEAR Limited Warranty Terms and Conditions Ardisam, Inc., a manufacturing company, warrants this Earthquake® FRONT TINE ROTOTILLER to be free from defects in the material or workmanship for a period of one year from the date of purchase. During the one-year warranty of this product, Ardisam will, at its discretion, furnish parts and labor to correct any defect caused by faulty material or workmanship.
Operator's Manual Front Tine Tiller 3310V NOTES _______________________________________________________________________________________________________ _______________________________________________________________________________________________________ _______________________________________________________________________________________________________ _______________________________________________________________________________________________________ ______________________________________________
Earthquake™, Division of Ardisam, Inc. 1160 8th Avenue, PO Box 666 Cumberland, WI 54829 800-345-6007 | Fax 715-822-2223 Email: info@ardisam.com Check for parts online at www.earthquake.