Operator's Manual CRT Rototillers 5040 6040E 5040 BRIGGS & stratton 4-cycle 206cc 8.50 ft-lbs gross torque 6040E VIPER ELECTRIC 4-cycle, 196 cc OMCRTC Revised 11-09-09 © 2009 Ardisam, Inc. All Rights Reserved.
Operator's Manual CRT Models 5040 and 6040E 1-YEAR Limited Warranty Terms and Conditions Ardisam, Inc., a manufacturing company, warrants this Earthquake® CRT Rototiller to be free from defects in the material or workmanship for a period of one year from the date of purchase. During the one year warranty of this product, Ardisam will furnish 100% parts and labor to correct any defect caused by faulty material or workmanship.
Operator's Manual CRT Models 5040 and 6040E INTRODUCTION Thank You . . . for purchasing an Earthquake® counter rotating rear-tine rototiller from Ardisam, Inc., and congratulations on your investment in quality. We have worked to ensure that this rear-tine rototiller meets the highest standards for usability and durability. With proper care, your rototiller will provide many years of service. Please take the time to read this manual carefully to learn how to correctly operate and maintain your rototiller.
Operator's Manual CRT Models 5040 and 6040E SAFETY OWNER’S RESPONSIBILITY Accurate assembly and safe and effective use of the rototiller is the owner’s responsibility. • Read and follow all safety instructions. • Carefully follow all assembly instructions. • Maintain the tiller according to directions and schedule included in this Earthquake operator’s manual. • Ensure that anyone who uses the tiller is familiar with all controls and safety precautions.
Operator's Manual CRT Models 5040 and 6040E c,. Fill fuel tank outdoors with extreme care. Never fill fuel tank indoors. d. Replace gasoline cap securely and clean up spilled fuel before restarting. • Never attempt to make any adjustments while the engine is running. Operation • Never operate the tiller without guards, covers, and hoods in place. • Never start the engine or operate the tiller with the wheels in the free-wheel position.
Operator's Manual CRT Models 5040 and 6040E SAFETY DECALS This rototiller unit has been designed and manufactured to provide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing.
Operator's Manual CRT Models 5040 and 6040E Unpacking and Assembly Your rototiller comes fully assembled except for a few parts. The following instructions will help you unpack your tiller and assemble and adjust your tiller’s depth regulator lever, cable tension and handlebar height. You will need 2- 9/16”wrenches. Unpack tiller 1. Open top of carton and remove handlebar assembly. 2. Find parts packet.
Operator's Manual CRT Models 5040 and 6040E Features forward drive safety control lever reverse drive safety control lever forward & reverse cable depth regulator lever bumper guard detent pin belt guard recoil start wheel lock pin Check for parts online at www.getearthquake.
Operator's Manual CRT Models 5040 and 6040E Operation PRE-START Inspection 1. Make sure all safety guards are in place and all nuts and bolts are secure. 2. Check oil level in engine crankcase. See your engine manual for procedure and specifications. 3. Inspect air cleaner for cleanliness. See your engine manual for procedure. 4. Check the fuel supply. Fill the fuel tank no closer than 1 inch from top of tank to provide space for expansion. See your engine manual for fuel recommendations. 5.
Operator's Manual CRT Models 5040 and 6040E Idle Speed Use the “low” position on the throttle lever to reduce stress on the engine when tilling is not being performed. Lowering the engine speed to “idle” will help extend the life of the motor, as well as conserve fuel and reduce the noise level of the equipment. Operating Speed For normal tilling, set the throttle lever to “fast”. SHUTTING DOWN To stop the engine at any time, move throttle control to the off position.
Operator's Manual CRT Models 5040 and 6040E Drive SAFETY Control Levers FORWARD LEVER Engages wheels forward and tines into counter rotation to the wheels. Pulling the drive safety control lever labeled (FORWARD) toward the handlebar engages the wheels and tines. Releasing the lever stops the wheels and tines and brings the tiller to a complete stop. forward lever engaged Caution Do not operate both “FORWARD” and “REVERSE” drive safety control levers at the same time.
Operator's Manual CRT Models 5040 and 6040E Wheel Lock pins Warning Place wheels in tilling position. 1. Remove lock pin. Align hole in axle with hole in wheel hub. (SEE FIGURE 2) 2. Insert lock pin through holes, fold lock pin ring to secure pin to axle. 3. Firmly lock wheel and axle together before tilling. 4. Repeat for other wheel. Never start engine or operate tiller with wheels in free-wheel position.
Operator's Manual CRT Models 5040 and 6040E DEPTH REGULATOR LEVER Tilling depth is controlled by the height of the depth regulator lever. To adjust tilling depth: (SEE FIGURE 4) 1. Remove detent pin. 2. Raise the depth regulator lever to position tines at chosen tilling depth. 3. Align hole in depth regulator lever with hole in depth regulator bracket and replace detent pin. Depth Regulator Lever Down = Shallower tilling.
Operator's Manual CRT Models 5040 and 6040E Tilling Tips The key to successful tilling is to begin with a shallow cut on the first pass, and then work an inch or two deeper on each successive pass. • Tilling depth will vary with ground conditions. • When beginning to till in unbroken ground or in extremely hard soil, set the detent pin in the highest hole of the drag stake (follow instructions under Tilling section). This will allow for shallow tilling.
Operator's Manual CRT Models 5040 and 6040E MAINTENANCE MAINTENANCE SCHEDULE Your rototiller has been designed and produced by the industry’s leading manufacturer of outdoor power equipment to provide you with years of reliable operation. Keeping your tiller in top running condition will prolong its life, and help you obtain optimum performance. Please read this normal care schedule, and note the recommended care operating intervals to extend the life of your unit.
Operator's Manual CRT Models 5040 and 6040E Change Forward/Reverse Belt 1. Turn off engine. Engine must be cool. 2. Remove spark plug wire and secure from spark plug. 3. Remove belt guard. •remove the forward belt from the forward engine pulley: - gently pull the engine recoil rope to rotate the pulley. - with the pulley turning, force the forward belt out of the pulley groove. - slide the belt free of the engine pulley. - pull the forward belt down and out of the way.
Operator's Manual CRT Models 5040 and 6040E Engine Maintenance Refer to the engine manual included in your parts packet for information on engine maintenance. Your engine manual provides detailed information and a maintenance schedule for performing the following tasks: 1. Check oil level before each use or after every 8 hours of operation. 2. Change oil after first 5-8 hours of operation. Change oil while engine is warm. Refill with new oil of recommended grade. 4.
Operator's Manual CRT Models 5040 and 6040E Lubrication Proper lubrication of moving mechanical parts is critical for proper care and maintenance. Oil the moving parts at 10 hour intervals using a 30 weight oil. Clean Tine Axle Shaft 1. Turn off engine. Engine must be cool. 2. Remove spark plug wire and secure from spark plug. 3. Tip the tiller forward. Block the tiller in position so that it rests on the engine mount and the tines are exposed. 4.
Operator's Manual CRT Models 5040 and 6040E Troubleshooting Warning Troubleshooting Guide While normal care and routine maintenance will extend the life of your rototiller, prolonged or constant use may eventually require that service be performed to allow it to continue operating properly. The troubleshooting guide below lists the most common problems, causes and remedies. Problem Engine will not start Practice safety at all times.
Operator's Manual CRT Models 5040 and 6040E PROBLEM REMEDY/ACTION Belts squeal in neutral and/or reverse • Adjust forward belt guide: - turn engine off and allow muffler to cool - disconnect spark plug wire and secure from spark plug - remove belt guard - pull down on drive safety control levers - manually bend forward belt guide so there is 1/16 inch or less clearance between belt guide and belt - replace belt guard and spark plug wire Belts squeal in forward operation • Adjust tabs on the reverse b
Operator's Manual CRT Models 5040 and 6040E CRT Handlebar parts 16 8 15 7 14 14 6 4 10 5 3 12 18 13 11 1 17 19 2 38 1 37 Check for parts online at www.getearthquake.
Operator's Manual CRT Models 5040 and 6040E CRT Handlebar parts list 6065ve electrical parts list REF. NO. PART # DESCRIPTION QTY. 1 2104 NUT HEX TWO-WAY 3/8-16 6 2 48762 BOLT 3/8-16 X 1” CARRIAGE 4 3 503 BOLT 5/16-18 X 1-1/2 HH 1 4 53606 NUT-NYLOC, #10 5 53607 6 REF. NO. PART # DESCRIPTION QTY. 20 -- ---- -- 21 300500 GROMMET, 1/2” ID 1 22 300501 NUT, WING M5 X .8 2 23 300502 SCREW, THUMB M5 X .
Operator's Manual CRT Models 5040 and 6040E CRT Motor Mount PARTS 48 47 14 18 49 13 14 25 23 18 21 6 20 5 4 50 51 12 11 15 16 28 29 36 35 19 33 34 9 10 14 37 24 12 9 6 11 7 16 17 8 1 25 14 16 27 2 14 23 52 52 51 50 16 10 26 42 22 3 56 14 38 18 16 32 30 18 26 31 31 39 43 45 18 16 16 18 44 41 45 40 53 54 55 Check for parts online at www.getearthquake.
Operator's Manual CRT Models 5040 and 6040E CRT Motor Mount PARTS LIST R E F . PART # NO. DESCRIPTION 1 332001 WELDMENT, ENGINE MOUNT 2 332003 3 R E F . PART # NO.
Operator's Manual CRT Models 5040 and 6040E CRT Tines & Hood parts 16 19 18 16 4 3 23 21 3 7 6 5 14 12 13 22 24 15 11 2 1 3 22 5 8 9 17 20 10 27 30 29 18 28 25 26 Check for parts online at www.getearthquake.
Operator's Manual CRT Models 5040 and 6040E CRT Tines & Hood parts list 26 R E F . PART # NO. DESCRIPTION QTY.
Operator's Manual CRT Models 5040 and 6040E CRT Wheel & Tiller Shaft PARTS & pARTS LIST 16 1 8 12 5 19 18 15 17 8 3 8 7 12 11 4 9 9 8 10 14 8 10 13 7 8 10 15 8 8 7 9 6 9 10 7 5 PARTS LIST 4 qty. 3 REF. nO. Description 1 BOLT, M6 X 25MM 6 2 COVER, REAR TRANSMISSION 1 3 GASKET, FRONT AND REAR TRANSMISSION COVER 2 4 SHIM, DRIVE SHAFT 6 5 BEARING, TAPPERED ROLLER 2 6 SHAFT, DRIVE CRT SHAFT 1 7 BUSHING, TINE AND WHEEL SHAFT 4 REF. NO.
Earthquake™, Division of Ardisam, Inc. 1160 8th Avenue, PO Box 666 Cumberland, WI 54829 800-345-6007 | Fax 715-822-2223 Email: info@ardisam.com Check for parts online at www.earthquake.
