Operator's Manual Original Operating Instructions Earth Auger Powerhead E43/E43CE English: ...................... Pages 1-21 Español: ............... Páginas 22-43 Français: ................Pages 43-67 Get parts online at www.GetEarthquake.com OME43 Rev. 08/04/11 © Copyright 2011 Ardisam, Inc. All Rights Reserved.
Operator's Manual Earth Auger Powerhead E43/E43CE THANK YOU AND CONGRATULATIONS.... on your purchase of a new EARTHQUAKE® POWERHEAD from Ardisam, Inc. We have worked to ensure that your Earthquake Powerhead will be one of the most trouble-free and satisfying pieces of equipment you have ever owned. With proper care, your powerhead will provide many years of service. Please take the time to read this manual carefully to learn how to correctly operate and maintain your equipment.
Operator's Manual Earth Auger Powerhead E43/E43CE WARNINGS AND SAFETY PRECAUTIONS OWNER’S RESPONSIBILITY Accurate assembly and safe, effective use of the auger is the owner’s responsibility. r 3FBE BOE GPMMPX BMM TBGFUZ JOTUSVDUJPOT r $BSFGVMMZ GPMMPX BMM BTTFNCMZ JOTUSVDUJPOT r .BJOUBJO UIF BVHFS BDDPSEJOH UP EJSFDUJPOT BOE TDIFEVMF JODMVEFE in this Earthquake operator’s manual. r &OTVSF UIBU BOZPOF XIP VTFT UIF BVHFS JT GBNJMJBS XJUI BMM DPOUSPMT and safety precautions.
Operator's Manual Earth Auger Powerhead E43/E43CE ENGINE SAFETY PRECAUTIONS CAUTION WARNING CARBON MONOXIDE POISONING All engines give off carbon monoxide, an odorless, colorless, poisonous gas, in the exhaust. Carbon monoxide may be present even if you do not smell or see any engine exhaust. Levels of carbon monoxide, which can be deadly, can be present for days in an enclosed area that has poor ventilation. Breathing carbon monoxide can cause nausea, fainting or death.
Operator's Manual Earth Auger Powerhead E43/E43CE ASSEMBLY TOOLS REQUIRED: r 5XP u 8SFODIFT ASSEMBLY INSTRUCTIONS: (SEE FIGURE 1) 1. Insert the output shaft of the E43 transmission (A) in the open end of the Flex Coil ShockTop (B). 2. Line up the bolt holes through the Flex Coil ShockTop and the output shaft of the transmission. 3. Place the included 3/8-16 x 1.5 inch bolt (C) through the bolt hole. A C D 4. )BOE UISFBE UIF i#J XBZu MPDL OVU % PO UIF CPMU 5.
Operator's Manual Earth Auger Powerhead E43/E43CE OPERATION STEPS FOR WORKING ON ENGINE OR AUGER 1. Turn off engine switch. 2. Disconnect the spark plug wire from the spark plug. 3. Securely place the disconnected spark plug wire away from the spark plug and any metal parts. This must always be done or arcing may occur between spark plug wire and metal parts. CAUTION DO NOT ALTER/MODIFY ENGINE OR AUGER: NEVER ALTER OR MODIFY THE ENGINE FROM THE FACTORY.
Operator's Manual Earth Auger Powerhead E43/E43CE FILLING GAS TANK 1. Shut-off engine and allow engine to completely cool before refilling the gas tank. 2. Move to a well ventilated area, outdoors, away from flames and sparks. 3. Clean debris from area around the gas cap. 4. Loosen gas cap slowly. Place the cap on a clean, dry surface. CAUTION ALWAYS HANDLE FUEL IN A WELL VENTILATED AREA, OUTDOORS, AWAY FROM FLAMES OR SPARKS. DO NOT START ENGINE IF FUEL IS SPILLED. WIPE OFF EXCESS FUEL AND ALLOW TO DRY.
Operator's Manual Earth Auger Powerhead E43/E43CE STARTING AND STOPPING ENGINE r .PWF FOHJOF UP B XFMM WFOUJMBUFE BSFB PVUEPPST UP QSFWFOU DBSCPO monoxide poisoning. r .PWF UP BO BSFB BXBZ GSPN óBNFT PS TQBSLT UP BWPJE JHOJUJPO PG vapors if present. r 3FNPWF BMM EFCSJT GSPN BJS DMFBOFS IPMFT BOE HBT DBQ UP FOTVSF QSPQFS air flow. COLD ENGINE START WARNING MAKE SURE THE UNIT IS IN A STABLE POSITION BEFORE PULLING THE STARTER HANDLE.
Operator's Manual Earth Auger Powerhead E43/E43CE MAINTENANCE AND STORAGE CAUTION POWER AUGER MAINTENANCE 1. The gear case has 4 oz. of grease installed at the factory. It is recommended that once a year the gear case be split and the grease level checked. Add grease only if level of grease is below top of the gears. DO NOT OVERFILL. TO PREVENT ACCIDENTAL STARTING: ENGINE MUST BE TURNED OFF AND COOL, AND SPARK PLUG WIRE MUST BE REMOVED FROM SPARK PLUG BEFORE CHECKING AND ADJUSTING ENGINE OR EQUIPMENT.
Operator's Manual Earth Auger Powerhead E43/E43CE STEPS FOR CLEANING BLOCK STYLE FOAM AIR FILTER - SEE PARTS EXPLOSION ON PAGE 16. 1. Before removing the air filter cover, move the choke lever to the choke position. (Figure 2) 2. To remove air filter cover, squeeze the latch tabs on both sides of the cover. (Figure 3) 3. Once the latch tabs are released, remove the air filter cover by rotating the cover away from the engine. (Figure 4) 4.
Operator's Manual Earth Auger Powerhead E43/E43CE SPARK PLUG 5IF SFDPNNFOEFE TQBSL QMVH JT B /(, #. " XIJDI DSPTT SFGFSFODFT to a Champion CJ8. CAUTION 1. Check spark plug at the beginning of each season. TO AVOID INJURY OR DEATH, NEVER SIPHON FUEL BY MOUTH. 2. Disconnect the spark plug cap, and clean any debris from around the spark plug area. NEVER STORE EARTH AUGER WITH FUEL IN THE GAS TANK INSIDE AN ENCLOSED AREA OR BUILDING. 3.
Operator's Manual Earth Auger Powerhead E43/E43CE SERVICE INFORMATION At Ardisam, we build quality and durability into the design of our products; but no amount of careful design by us, and careful maintenance by you, can guarantee a repair-free life for your machine. Most repairs will be minor, and easily fixed by following the suggestions in the troubleshooting guide in this section. CAUTION PRACTICE SAFETY AT ALL TIMES.
Operator's Manual Earth Auger Powerhead E43/E43CE TROUBLESHOOTING PROBLEM POSSIBLE CAUSE REMEDY/ACTION Engine will not start 1. Power switch off 1. Flip switch to ON position Engine runs rough, floods during operation Engine is hard to start Engine misses or lacks power Engine runs, then quits 2. Spark plug wire disconnected 2. Connect spark plug wire to spark plug 3. Out of fuel 3. Refuel 4. Spark plug wet, faulty or improperly gapped 4. Clean, replace or gap spark plug 5.
Operator's Manual Earth Auger Powerhead E43/E43CE E43 POWERHEAD & AUGER PARTS 1 ALTERNATE ASSEMBLY FOR CLUTCH DRUM & PINION GEAR 9 35 6 4 11 2 5 3 7 9 33 33 8 25 25 32 32 10 15 26 26 16 27 27 24 11 17 12 16 13 23 23 14 12 10 26 25 22* 22* 18 10 19 21 29 29 28** 28** 30 30 20 31 31 * Includes blade, fishtail point, shock spring, shock top, & hardware. ** Includes mounting hardware. 14 Check for parts online at www.getearthquake.
Operator's Manual Earth Auger Powerhead E43/E43CE E43 POWERHEAD PARTS LIST KEY NO. PART NO. DESCRIPTION AUGER PARTS & ACCESSORIES LIST QTY. KEY NO. 23 PART NO. DESCRIPTION QTY.
Operator's Manual Earth Auger Powerhead E43/E43CE 47 13 19 6 5 7 4 16 47 18 39 48 45 17 36 46 37 38 8 53 16 15 41 2 1 51 9 10 12 44 3 52 21 47 11 24 43 22 42 49 26 25 23 33 34 28 14 20 35 31 32 50 29 30 27 40 E43 ENGINE PARTS Check for parts online at www.getearthquake.
Operator's Manual Earth Auger Powerhead E43/E43CE E43 ENGINE PARTS LIST KEY NO. PART NO. QTY. KEY NO. PART NO.
Operator's Manual Earth Auger Powerhead E43/E43CE E43 EARTH AUGER POWERHEAD Warranty Terms and Conditions PRODUCT WARRANTY: 1-YEAR LIMITED WARRANTY Ardisam, Inc., a manufacturing company, warrants this EARTHQUAKE® EARTH AUGER POWERHEAD to be free from defects in the material or workmanship for a period of one year from the date of purchase. During the one-year warranty of this product, Ardisam will furnish, at their discretion, parts and labor to correct any defect caused by faulty material or workmanship.
Operator's Manual Earth Auger Powerhead E43/E43CE Explanation of Emissions Control Warranty Provisions Viper Engines are designed, built and equipped to meet all EPA requirements. It warrants that it is free from defects in material and workmanship that could cause failure to the warranted part; and that it is identical in all material respects to the engine described in the manufacturer’s application for certification.