Product Manual

Check for parts online at www.getfieldsedge.com or call 800-345-6007 M-F 8-5 15
Operator's Manual
String Mower M200
IMPORTANT
TEST THE DRIVE SYSTEM. START THE ENGINE AND
ENGAGE AND DISENGAGE THE MOWER HEAD
SEVERAL TIMES. WHEN DISENGAGED, MAKE SURE THE
MOWER HEAD COMPLETELY STOPS WHEN RESTING
ON THE GROUND. IF THE MOWER HEAD CONTINUES
TO ROTATE, TAKE THE MOWER TO AN AUTHORIZED
SERVICE CENTER.
FIGURE 21: Routing The Drive Belt
“V” PULLEY
BELT GUIDES
DRIVE
PULLEY
MOUNTING
BOLT
RETURN SPRING
DRIVE BELT
STORAGE
When the mower is put in storage for thirty days or more, follow
the steps below to make sure the mower is in good condition
the following season.
Mower:
Completely clean the mower
Remove and discard line or store in a sealed container. Put the
mower in a building that has good ventilation.
NOTE: A yearly check-up or tune-up at an authorized service
dealer will ensure that the mower will provide maximum
performance for the next season.
Engine:
IMPORTANT NOTE: It is important to prevent gum deposits
from forming in fuel system parts such as the carburetor,
fuel filter, fuel hose, and tank during storage. Also, using
alcohol blended fuels (called gasohol, ethanol or methanol)
can attract moisture which leads to separation and
formation of acids during storage. Acidic gas can damage
the fuel system of an engine while in storage.
1. Drain all gasoline from the fuel tank. Let the engine run until
it is out of gasoline. If you do not want to remove gasoline,
add a fuel stabilizer to any gasoline left in the tank. A fuel
stabilizer will minimize the formation of gum deposits and
acids. If the tank is almost empty, mix the fuel stabilizer
WARNING
DO NOT REMOVE GASOLINE WHILE INSIDE A
BUILDING, NEAR A FIRE, OR WHILE YOU SMOKE.
GASOLINE FUMES CAN CAUSE AN EXPLOSION OR A
FIRE.
with fresh gasoline in a separate container and add the
mixture to the tank. Always follow the instructions on the
stabilizer container. Run the engine at least ten minutes
after stabilizer is added to allow the mixture to reach the
carburetor.
2. Drain the oil from a warm engine. Fill the engine crankcase
with new oil.
3. Remove the spark plug from the cylinder. Pour one ounce
of oil into the cylinder. Slowly pull the recoil starter handle
so that the oil will protect the cylinder. Install a new spark
plug in the cylinder.
4. Completely clean the mower, including dirt and debris
from the cylinder cooling fins and the engine housing.
5. When not in use, disconnect spark plug lead and store in a
well-ventilated area inaccessible to children.
TROUBLESHOOTING & REPAIR
At Fields Edge™, we build quality and durability into the design
of our products; but no amount of careful design by us, and
careful maintenance by you, can guarantee a repair-free life for
your Fields Edge™ String Mower. Most repairs will be minor, and
easily fixed by following the suggestions in the troubleshooting
guide in this section.
The guide will help you pinpoint the causes of common problems
and identify remedies.
For more complicated repairs, you may want to rely on an
authorized service center. A parts breakdown is located toward
the end of this manual.
We will always be glad to answer any questions you have, or
help you find suitable assistance. To order parts or inquire about
warranty, call or email us using the contact information found
below.
ORDERING REPLACEMENT PARTS
Parts can be obtained from the store where the string mower
was purchased or direct from the factory. To order parts visit
www.getfieldsedge.com or call 1-800-345-6007.
For other general questions, you can e-mail us at info@
getfieldsedge.com.
Please include the following information with your order:
1) Part numbers
2) Part description
3) Quantity
4) Model number and serial number