The Sound That Will Move You MINIME P8V2/P8WV2 USER’S MANUAL Earthquake Sound Corp. | (510) 732-1000 | U.S. Toll Free: (800) 576-7944 | www.earthquakesound.
Table of Contents About Earthquake Sound Corporation.................................................. 3 Safety Instructions................................................................................. 4 - 5 Introduction........................................................................................... 6 What Makes a MiniMe?.......................................................................... 6 Control Panel Overview.........................................................................
About Earthquake Sound Corporation For over 28 years, Earthquake Sound has been producing a variety of high quality audio products that have impressed audiophile communities around the world. It all started in 1984 when Joseph Sahyoun, a music freak and Aerospace Engineer unhappy with the existing loud speaker technology and performance, decided to put his advance engineering knowledge to use. He pushed technological boundaries to the limit to create the kind of subwoofer he could live with.
Safety Instructions Safety First This documentation contains general safety, installation, and operating instructions for the MiniMe P8V2/P8WV2 subwoofer. It is important to read this user’s manual before attempting to use this product. Pay particular attention to the safety instructions. Symbols Explained: Appears on the component to indicate the presence of uninsulated, dangerous voltage inside the enclosure – voltage that may be sufficient to constitute a risk of shock.
Connection Tips ? Keep all power cords away from all signal cables to prevent humming from induced noise. ? Choose reliable signal cable cords (Earthquake Sound also specializes in high performance RCA cables and patches). ? All speaker wires that are ran through the walls should be twisted type to reduce potential hum noise pick-up. ? It is best to use a grounded electrical outlet to power the amplifier. Lack of input ground reference could be unsafe.
Introduction The MiniMe system is designed to dramatically enhance your enjoyment of music and films at home by adding power and impact to low frequency sound effects without taking up your entire living space. Congratulations and thank you for choosing the Earthquake MiniMe P8V2/P8WV2 subwoofer as a key component of your audiophile system.
Control Panel Overview (1) (2) (3) (4) (5) (6) (1) LED Power Signal Indicator This LED indicator reflects the main power status of the amplifier as well as the state of the amplifier (whether the AUTO Sensing is on/off and whether signal is being fed to the amplifier). Note that this LED will only light up when the main power switch is in the ON position.
Control Panel Overview continued (7) (8) (9) (10) (11) (7) Low Level RCA Inputs This the best way to drive audio signal to the MiniMe FF8V2. NOTE: DO NOT USE HIGH LEVEL AND LOW LEVEL INPUTS AT THE SAME TIME (8) LFE/SUB Operation Mode Switch When the switch is in LFE position, the subwoofer is running in full range mode (20Hz 2kHz) and the frequency adjustment is disabled.
Placing Your Subwoofer(s) You often hear the term “subwoofers are nondirectional.” This is not true. It is harder to choose subwoofer placement when low frequencies are crossed. The wider the room, the more directional the subwoofer. The easiest solution is to use two (2) subwoofers, feed a mono signal to both and place them in the front, one on the left and another on the right.
Connecting Your Subwoofer(s) Low Level Setup - Single Sub PRE OUT (SINGLE) back of typical processor/receiver This is the best way to drive an audio signal into the MiniMe P8V2/P8WV2. Today, all signal processors (5.1/6.1 and more advanced ones) come equipped with built-in pre-amplifier outputs (RCA) that include a subwoofer output. Generally, the SUB PRE OUT is in mono format. Connect the SUB PRE OUT from the processor/receiver to the MiniMe P8V2/P8WV2’s LOW LEVEL INPUT using a “Y” RCA cable.
High Level Setup - Single Sub The MiniMe P8V2/P8WV2 has a high/speaker level input connection. This setup is a solution when you experience excessive noise or hum with the line level input. Simply connect the speaker wire (up to 16-gauge) from the receiver’s SPEAKER OUTPUTS to the MiniMe P8V2/P8WV2’s SPEAKER . Remember to always connect red-to-red and blackto-black when making connections between a receiver/processor to the subwoofer.
Connecting Your Subwoofer(s) cont’d High Level Single Sub + Satellite Setup The MiniMe P8V2/P8WV2 has a high/speaker level output connection that can be used to drive the stereo front or rear speakers. Using speaker wires (up to 16-gauge), simply connect the receiver’s front speaker outputs to the MiniMe P8V2/P8WV2 speaker level inputs. Then using speaker wires, connect the MiniMe P8V2/P8WV2 speaker level outputs to the speakers.
High Level - Dual Sub Connect the speaker wire (up to 16-gauge) from the receiver’s RIGHT SPEAKER OUTPUTS to the MiniMe P8V2/P8WV2’s RIGHT SPEAKER INPUTS. Then, connect the speaker wire from the receiver’s LEFT SPEAKER OUTPUTS to the MiniMe P8V2/P8WV2’s LEFT SPEAKER INPUTS. Remember to always connect red-to-red and blackto-black when making connections between a receiver/processor to the subwoofer. You will notice a lack of bass from your subwoofer if you inadvertently reverse one of the connections (i.e.
Adjusting the controls There are two main methods for adjusting the level, crossover frequency and phase of the Earthquake MiniMe P8V2/P8WV2 to match a system: Use the following charts to record more desirable data from test results. ? Method 1 - Typical By listening and making adjustments to suit your preference. ? Method 2 - Laboratory By measuring the output and adjusting for a flat frequency response. Satisfactory results can be achieved if you make the adjustments based simply on listening.
MiniMe P8V2/P8WV2 Subwoofer Dimensions and Specifications 11 1/2” (290mm) 10 1/2” (265mm) With Amplifier With Grille 11” (278mm) With Feet Enclosure Type Ported Enclosure with Passive Amplifier Power 320 Watts MAX Drivers 8” Premium Extended Excursion Subwoofer 8” Patented SLAPS (Symmetrically Loaded Audio Passive System) Frequency Response 25Hz - 160Hz Crossover Frequency 50Hz - 160Hz Signal Sensing AUTO/ON/OFF Inputs/Outputs Low Level RCA & High Level Speaker Inputs High Level Speaker Ou
5 Year Limited Warranty Information Earthquake warrants the original purchaser that all Factory Sealed New Audio Products to be free from defects in material and workmanship under normal and proper use for a period of five (5) years from the date of purchase (as shown on the original sales receipt with serial number affixed/written on it).
(F) Shipping Instructions: Product(s) must be packaged in its original protective box(es) to minimize transport damage and prevent repackaging cost (at the ongoing rates). Shipper claims regarding items damaged in transit must be presented to carrier. Earthquake Sound Corporation reserves the right to refuse improperly packed product. A copy of the original sales receipt must accompany product returned to service. We encourage you to include with the package a written description of the problem.
For Your Records Date of Purchase: ________________________ Authorized Dealer/Installer Info: Name: _____________________________________ Address: _____________________________________ _____________________________________ Phone: _____________________________________ Serial Number: Notes ___________________________________________________________________________________________ ___________________________________________________________________________________________ _____________________________
Specifications are subject to change without notice.
The Sound That Will Move You Earthquake Sound reserves the right to amend details of the specifications without notice. © Copyright Earthquake Sound Corporation Earthquake Sound Corporation 2727 McCone Avenue. Hayward CA, 94545.
