Manual

HELPFUL HINTS: READ THE DIRECTIONS BEFORE ASSEMBLY

THIS SPREADER COMES PARTIALLY ASSEMBLED, REQUIRING YOU TO INSTALL THE WHEELS, HANDLE ASSEMBLY AND

CONTROL ROD. IT SHOULD TAKE APPROXIMATELY 10 MINUTES WITH THE USE OF TWO 7/16” WRENCHES AND 1 PAIR

OF PLIERS.

; Clean the impeller plate after each use. Material build up on the impeller blades will cause uneven spreading.

; Your spreader is designed to be pushed at three miles per hour, which is a brisk walking speed. Slower or faster speeds

will change the spread patterns. Wet material will also change the spread pattern and ow rate.

; Clean your spreader thoroughly after each use. Wash between the shut off plate and bottom of the hopper.

; Gears are permanently lubricated at the factory. Do not open the gearbox or dirt may enter.

; When using Rock Salt remove salt from the hopper daily. Rock Salt will reconstitute back into a solid block over night

with humidity. As a preventative measure, spray all metal parts thoroughly (inside the tubing too) with a spray oil to

prevent corrosion on painted chassis models.

1. Open carton and remove the handle assembly, wheels, and spreader from

carton.

2. Turn spreader upside-down on to the hopper.

8-2013 Pt.# 53107ss PAGE 1

2130SS HIGH-OUTPUT Broadcast spreader

ASSEMBLY and OPERATING INSTRUCTIONS



Gearbox &

Axle Assembly

Lower

Handle

Frame

Brace

Cross Brace

Axle Bushing

3. Ensure that the axle bearings are pushed into the axle

bushing on both sides as shown. Install drive wheel (both

wheels are interchangeable) to axle using pin hole nearest to

lower handles as shown. Insert 2” cotter pin through wheel

and through axle. Bend with pliers to prevent pin from falling out.

4. Install coast wheel to axle, then using outside pin hole as shown, insert 1” cotter

pin through axle (not thru the wheel). Bend with pliers to prevent pin from falling

out.

2” Cotter Pin

1” Cotter Pin

Coast Wheel

Drive Wheel

PLEASE CALL IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY QUESTIONS

REGARDING THE SAFE OPERATION OF THIS SPREADER. THIS MODEL INCLUDES LIFETIME TECHNICAL SUPPORT

SUPPORT HOT LINE: 574-848-7491 or 800-294-0671, email: techsupport@earthway.com

PAGE 1
2130SS HIGH-OUTPUT Broadcast Spreader ASSEMBLY and OPERATING INSTRUCTIONS  PLEASE CALL IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY QUESTIONS REGARDING THE SAFE OPERATION OF THIS SPREADER. THIS MODEL INCLUDES LIFETIME TECHNICAL SUPPORT SUPPORT HOT LINE: 574-848-7491 or 800-294-0671, email: techsupport@earthway.
PAGE 2
5. Install handle shaft to lower handles and pivot & bracket assembly as shown. Using 2” bolts and locknuts. TIGHTEN BOLTS AND NUTS NOW. 1/4 - 20 Lock-nut Pivot Bracket 1/4 - 20 x 2” Bolt Upper Handles 6. (This step is only required if you want to change the position of the handles) NOTE: BEFORE INSTALLING GAUGE AND UPPER HANDLES TO HANDLE SHAFT, UPPER HANDLES FEATURE THREE POSITIONS FOR OPERATOR’S COMFORT.
PAGE 3
5-YEAR LIMITED WARRANTY Earthway Products, Inc. warrants this product free of defects in original workmanship and materials for a period of 5-Years to the end user with the original purchase receipt. If a manufacturing non-conformance is found, Earthway Products, Inc. at its discretion will repair or replace the part(s) or product at no charge provided the failure is not the result of incorrect installation, mishandling, misuse, tampering, or normal wear and tear as determined by Earthway.
PAGE 4
Earthway Products, Inc. P.O. Box 547 Bristol, IN 46507 Phone: 800-294-0671 www.earthway.