User Manual

ManualsBrandsEarthway ManualsGardening equipmentC25HDS Stainless Steel Professional Tow Broadcast Spreader

Your spreader is shipped semi assembled, you will need (2) 7/16” wrenches, a cutting tool to cut through the plastic zip-ties,

and a pair of pliers to bend the cotter pins that hold the wheels to the axle.

1. Remove the spreader and identify all loose parts from carton.

2. Remove the Zip-ties holding the Control Support ASSembly to the CroSS brACe and the 2 bolts that are in the frame

12-2011 Pt# 52155 PAGE 1

C25 SerieS profeSSionAl tow

broAdCASt SpreAder

ASSEMBLY and OPERATING INSTRUCTIONS

EV-N-SPRED

EarthWay

PLEASE CALL IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY QUESTIONS

REGARDING THE SAFE OPERATION OF THIS SPREADER. THIS MODEL INCLUDES LIFETIME TECHNICAL SUPPORT

SUPPORT HOT LINE: 574-848-7491 or 800-294-0671, emAil: teChSupport@eArthwAy.Com

HELPFUL HINTS: READ THE DIRECTIONS BEFORE ASSEMBLY

; If your spreader does not spread evenly, be sure the FRONT on the gear box points away from the tow bar of the spreader.

The impeller must turn clockwise. Reversing the gearbox will cause the impeller to turn counter clockwise. Clean the

impeller plate after each use. Fertilizer stuck on the impeller blades will cause uneven spreading.

; Your spreader is designed to be pulled at three miles per hour, which is a brisk walking speed. Slower or faster speeds will

change the spread patterns. Wet fertilizer will also change the spread pattern and ow rate. Clean and dry your spreader

thoroughly after each use. A coating of light spray oil on all metal parts, (including the inside of the frame tubing) will help

prevent corrosion. Wash between the shut off plate and bottom of the hopper.

; Gears are permanently lubricated at the factory. Do not open the gearbox or dirt may enter.

OVER

3 MPH

Do not tow

faster than

3 MPH

ROCK SALT and POWDERED MATERIALS

should not be used in this spreader as it will

damage gearbox and can void warranty.

Use only granular materials.

Remove

Zip-ties

Remove

¼-20 x 2¼” Bolts

washers & lock nuts

#40003

Screen

#19117 Wheels

#36103

1” Cotter Pin

#36104

2” Cotter Pin

Hitch

Assembly

#42251 Clevis Pin

#36108 Hair Pin Clip

Control Support

Assembly

Summary of content (5 pages)

PAGE 1
C25 Series Professional Tow Broadcast Spreader Earth Way EV-N-SPRED R ASSEMBLY and OPERATING INSTRUCTIONS PLEASE CALL IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY QUESTIONS REGARDING THE SAFE OPERATION OF THIS SPREADER. THIS MODEL INCLUDES LIFETIME TECHNICAL SUPPORT SUPPORT HOT LINE: 574-848-7491 or 800-294-0671, email: techsupport@earthway.
PAGE 2
3. Lift the Draw Bar into position and replace the ¼-20 x 2 ¼” bolts washer and nut as shown below. Now tighten those bolts and the other frame bolts. 4. Install Drive Wheel to the Axle using pin hole nearest to lower handles as shown. Insert 2” cotter pin through Wheel and through Axle. Bend with pliers to prevent pin from falling out. 5. Install Coast Wheel to Axle, using outside pin hole, insert the 1” cotter pin through Axle (not thru the wheel). Bend with pliers to prevent pin from falling out.
PAGE 3
Tensioning Nut 30 0 ¼-20 Regular Nuts Slide Control Rod into Pivot Bracket then add ¼” Hex Nut Pivot Bracket Calibration Point Control Rod 8. Next push Lever forward to setting “0” now align Control Rod with hole in Pivot Bracket, now pull Lever backward to insert Control Rod through hole in Pivot Bracket. Now install ¼-20 regular nut on to Control Rod. Make sure that there is a Hex Nut on both sides of the Pivot Bracket tab. 9. Pull Lever back to setting “30” as shown.
PAGE 4
5-YEAR LIMITED WARRANTY Earthway Products, Inc. warrants this product to be free of defects in original workmanship and materials for a period of 5-Years to the end user with the original purchase receipt. If a manufacturing non-conformance is found, Earthway Products, Inc. at its discretion will repair or replace the part(s) or product at no charge provided the failure is not the result of incorrect installation, mishandling, misuse, tampering, or normal wear and tear as determined by Earthway .
PAGE 5
1 5 4 5 39 37 38 6 30 14 vv vv vv vv 28 5 30 19 28 34 35 33 8 60060R OPTIONAL Heavy-Duty Rain Cover & Side Deflector Kit 8 7 vv 15 30 15 17 11 vv 13 9 vv 5 vv 12 2 32 10 29 36 5 27 77002 OPTIONAL Heavy-Duty Rain Cover 6 20 30 18 30 8 Earthway Products, Inc. P.O. Box 547 Bristol, IN 46507 Phone: 800-294-0671 www.earthway.