Instructions / Assembly

ManualsBrandsEasyFlex ManualsCSST Pipe1/2 in. MIP x 1/2 in. MIP x 36 in. Coated Stainless Steel Gas Connector (1/2 in. O.D.) with Gastop EFV (71,100 BTU)

888 577 8999 • info@easyflexusa.com • easyflexusa.com

Tubing

MATERIAL

Stainless Steel 304

Coating

Epoxy

Fitting Zinc-Plated Steel S45C

Types

AVAILABILITY

Stainless Steel (Uncoated)

Yellow Epoxy Coated Stainless Steel

Black Epoxy Coated Stainless Steel

Fittings

3/8” MIP EFV (1/4” Tapped FIP)

3/8” FIP EFV

1/2” MIP EFV (3/8” Tapped FIP)

1/2” FIP EFV

1/2” MIP EFV (3/8” Tapped FIP)

1/2” FIP EFV

3/4” MIP EFV (1/2” Tapped FIP)

3/4” FIP EFV

3/4” MIP EFV (1/2” Tapped FIP)

3/4” FIP EFV

1” MIP EFV (3/4” Tapped FIP)

1” FIP EFV

3/8” MIP EFV (1/4” Tapped FIP)

3/8” FIP EFV

1/2” MIP EFV (3/8” Tapped FIP)

1/2” FIP EFV

Lengths

Flare End /

Tube Dia.

12”, 18”, 24”, 30”, 36”, 48”, 60”, 72”

3/8” OD (1/4” ID) 1/2” OD (3/8” ID) 5/8” OD (1/2” ID) 1” OD (3/4” ID)

Rated Operating Temperature

PRESSURE TEMPERATURE

-40°F to 150°F (-40°C to 65°C)

Rated Pressure

0.5 psi

In the case of a gas line rupture or a disconnect from the appliance, Easyflex EFV detects increase of gas flow and immediately

shut-off the supply of gas. Gas flow is controlled only at the appliance where the problem exists. The valve will remain

activated until the gas line is properly repaired.

• Automatic Activation • Automatic Reset • No Battery Needed • 100% Performance Tested

CERTIFICATIONS

ANSI Z 21.24/ CSA 6.10 Connectors for Gas Appliances

ANSI Z 21.75/ CSA 6.27 Connectors for Outdoor Appliances and Manufactured Homes

ANSI Z 21.93/ CSA 6.30 Excess Flow Valves for Natural and LP Gas with Pressures of Up to 5 psig

easyflexusa.com

INSTALLATION INSTRUCTIONS

Stainless Steel Flexible

Gas Connectors with EFV

(Excess Flow Valve)

Summary of content (3 pages)

PAGE 1
INSTALLATION INSTRUCTIONS easyflexusa.com Stainless Steel Flexible Gas Connectors with EFV (Excess Flow Valve) In the case of a gas line rupture or a disconnect from the appliance, Easyflex EFV detects increase of gas flow and immediately shut-off the supply of gas. Gas flow is controlled only at the appliance where the problem exists. The valve will remain activated until the gas line is properly repaired.
PAGE 2
INSTALLATION INSTRUCTIONS Required System Components Required Tools • Easyflex Gas Connector with EFV • Two 10” adjustable wrenches • Pipe thread sealant Note • Leak detection solution • Cleaning rag • Fuel codes require installation of a manual shut-off valve in the same room that is whithin easy reach of the appliance (i.e within 6 feet). • A shut-off valve is not included with this connector.
PAGE 3
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 1. Clean all pipe threads with a soft bristle brush and rag to ensure connections are free of any debris such as metal shaving, rust, dirt, oil, or water. 2. Apply pipe thread sealant to the male pipe threads of connection. DO NOT apply grease, oil, sealant, or tape to flare ends of fitting or shut-off valve. Sealant and tape will prevent this connection from sealing properly. • WARNING: Turn off gas supply before disconnection old appliance.