Cut Sheet

ManualsBrandsEaton B-Line ManualsConduitB-LINE 1212-HSCA HINGE SCREW COVER

Lay-In Wireway

Type 1 Quick-Connect Hinge Cover

Data Sheet

Notes: We can provide special sizes, finishes and other modifications. Consult the factory for your special requirements.

Cable & Wire Management

Construction

• Wireway body and cover are fabricated from code gauge steel,

(see table, page 16)

• Wireway body has mounting holes on the back

• Wireway is available with or without knockouts

• Wireway fittings have no knockouts, ends are available with or

without knockouts

• Wireway exceeding 72 inches in length has two overlapping

covers

• Variety of fittings allow runs which can change directions,

junction and terminate

• Wireway connectors (sold separately) have a gate feature

which can swing completely open allowing for lay-in of wire

and cable

• Universal style connectors are also available for adapting to

other manufacturer’s wireway, (see page 17)

• Except for wireway ends, completely interchangeable with

Type 1 screw cover wireway and fittings through use of the

adapter style connector HSCA, (see page 17)

Discount Schedule: A2

Subclass: HS1

Application

• Houses runs of control and power cable

• Used for cable and wire junction, distribution and

termination

Standards

• UL 870 listed, Type 1

• CSA C22.2 No. 26 certified, Type 1

• Conforms to NEMA standard for Type 1

Finish

• Wash and phosphate undercoat

• ANSI 61 gray acrylic electrocoat finish

Accessories

• Touch-up paint

• See Accessories section

Protected by U.S. Patents 7,525,044 &

7,762,042

Reversible and

removable hinge

cover

Pre-installed

hardware on quick

connector

Cable & Wire Management

B-Line series electrical enclosures Eaton

Summary of content (6 pages)

PAGE 1
Cable & Wire Management Cable & Wire Management Lay-In Wireway Type 1 Quick-Connect Hinge Cover Data Sheet Pre-installed hardware on quick connector Reversible and removable hinge cover Application Construction • Houses runs of control and power cable • Used for cable and wire junction, distribution and termination • Wireway body and cover are fabricated from code gauge steel, (see table, page 16) • Wireway body has mounting holes on the back • Wireway is available with or without knockouts • Wireway
PAGE 2
Cable & Wire Management Cable & Wire Management Lay-In Wireway Type 1 Quick-Connect Hinge Cover Illustration Sheet and Catalog Number Wireway Catalog Number Subclass: HS1 Wireway Size Height x Depth x Length Knockout Quantity D AxBxC KO No KO in. mm in.
PAGE 3
Cable & Wire Management Illustration Sheet and Catalog Number Subclass: HS1 Reducer C Telescopic Fitting B Adjustable length up to 10.00” (254 mm). Wraps around the two near joining wireway lengths to achieve a continuous run. A B1 B dimensions (see catalog table), correspond to the large end opening. Used to reduce or enlarge wireway runs. Removable cover is secured with screws.
PAGE 4
Cable & Wire Management Cable & Wire Management Lay-In Wireway Type 1 Quick-Connect Hinge Cover Illustration Sheet and Catalog Number Subclass: HS1 Wireway Hangers F Wireway End Flange K Allows for a secure connection of wireway to an adjoining enclosure or wall. A E K G G (shipped unassembled) J B Wireway End Flange Catalog Number A in. B mm in. E F mm in. mm in. mm 22 HSF 2.50 63 2.50 63 4.00 102 4.00 102 44 HSF 4.00 102 4.00 102 5.50 140 5.50 140 66 HSF 6.
PAGE 5
Cable & Wire Management Illustration Sheet and Catalog Number Subclass: HS1 90° Elbow Wireway 90˚ Elbows Catalog Number 22 HSL IN 44 HSL IN 66 HSL IN 88 HSL IN 1010 HSL IN 1212 HSL IN 22 HSL OUT 44 HSL OUT 66 HSL OUT 88 HSL OUT 1010 HSL OUT 1212 HSL OUT 22 HSL SIDE 44 HSL SIDE 66 HSL SIDE 88 HSL SIDE 1010 HSL SIDE 1212 HSL SIDE B A B A Inside Opening Specifically designed to have only the inside cover hinge open to allow a continuous run with 90˚ turns.
PAGE 6
Cable & Wire Management Cable & Wire Management Lay-In Wireway Type 1 Quick-Connect Hinge Cover Illustration Sheet and Catalog Number Subclass: HS1 Tee Tee Catalog Number Side hinge cover design for applications where a “T” junction is necessary. 22 HST 44 HST 66 HST 88 HST 1010 HST 1212 HST B A A B E F in. mm in. mm in. mm in. mm 2.50 4.00 6.00 8.00 10.00 12.00 63 102 152 203 254 305 2.50 4.00 6.00 8.00 10.00 12.00 63 102 152 203 254 305 5.38 6.15 7.15 8.15 9.15 10.