Cut Sheet

ManualsBrandsEaton B-Line ManualsBoxes & EnclosuresN3R HC ENCLOSURE 12X12X6

Type 3R Small Continuous Hinge Cover Enclosures

Data Sheet

Construction

• Enclosure and cover are fabricated from (16) gauge galvaneal

steel

• Knockouts are furnished on bottom end

• Cover is secured to the body with a continuous hinge and

stainless steel pin on one side and a padlockable draw pull

catch on the opposite side

• #10-32 tapped hole provision for optional ground lug kit

• #10-32 weldnuts are furnished for mounting optional panel

• External mounting feet are provided for secure wall

mounting

Finish

• Wash and phosphate undercoat

• ANSI 61 gray polyester powder finish

Accessories

• Panels

• Ground lug kit

• Touch-up paint

• See Accessories section

• #8-32 self tapping screw (10168)

Application

• Used as wiring boxes, junction and pull boxes

• Protects against falling rain, sleet and external

ice formation

Standards

• UL 50 listed, Type 3R

• CSA C22.2 No. 40 certified, Type 3R

• Conforms to NEMA standard for Type 3R

• IEC 60529, IP32

Enclosure Enclosure Size Knockout Panel

Pattern Catalog Number

Panel

Height x Width x Depth

A x B x C

Height x Width

Catalog Number in. mm Bottom

Solid Perforated

in. mm

664 RHC 6.00x6.00x4.00 152x152x102 N66P N66PP 4.25x4.25 108x108

864 RHC 8.00x6.00x4.00 203x152x102 N86P N86PP 6.25x4.25 159x108

884 RHC 8.00x8.00x4.00 203x203x102 N88P N88PP 6.25x6.25 159x159

886 RHC 8.00x8.00x6.00 203x203x152 N88P N88PP 6.25x6.25 159x159

1086 RHC 10.00x8.00x6.00 254x203x152 N108P N108PP 8.25x6.25 210x159

12106 RHC 12.00x10.00x6.00 305x254x152 N1210P N1210PP 10.25x8.25 260x210

12126 RHC 12.00x12.00x6.00 305x305x152 N1212P N1212PP 10.25x10.25 260x260

IJK

JKL

HIJ

Type 3/3R Enclosures

Notes: Cooper B-Line can provide special sizes, finishes and other modifications. Consult the factory for your special requirements.

Type 3 / 3R Enclosures

Summary of content (2 pages)

PAGE 1
Type 3 / 3R Enclosures Type 3R Small Continuous Hinge Cover Enclosures Data Sheet Construction Type 3/3R Enclosures • Enclosure and cover are fabricated from (16) gauge galvaneal steel • Knockouts are furnished on bottom end • Cover is secured to the body with a continuous hinge and stainless steel pin on one side and a padlockable draw pull catch on the opposite side • #10-32 tapped hole provision for optional ground lug kit • #10-32 weldnuts are furnished for mounting optional panel • External mounting
PAGE 2
Type 3 / 3R Enclosures Type 3R Small Continuous Hinge Cover Enclosures Illustration Sheet B 3.00 C (76) .19 x .44 (5 x 11) Type 3/3R Enclosures weldnut .50 offset B-1.00 A+1.00 (25) (25) A A-2.37 C-.44 (11) A-1.50 draw pull catch (38) (60) mounting feet B-2.37 (60) continuous hinge knockout area (see table for pattern, see detail for size) 1.62” (41) H 3/4-1 1.62” (41) I 1/2-3/4 1.62” (41) J 3/4-1 1.