Specification Sheet
S
P E C I F I C A T I O N F E A T U R E S
HALO
®
D E S C R I P T I O N
The H1499TAT is a small aperture low voltage Non-IC AIR-TITE™
housing for providing accent and task lighting. The H1499TAT is
designed for use in non-insulated ceilings. Non-IC Housing is AIR-
TITE™ but insulation must be kept 3 inches away from all sides of
housing.
4-3/8
(111 mm)
Ceiling opening
5 inch
(127 mm)
1/2 inch
(13 mm)
8 inch
(203 mm)
5-1/4 inch
(133 mm)
H1499TAT
4" Non-Insulated
Ceiling
AIR-TITE™
Low Voltage
Recessed Housing
4 " T R I M S
T o p V i e w
F O R U S E I N
N O N I N S U L A T E D
C E I L I N G S
O R
I N S U L A T E D C E I L I N G S
W H E R E I N S U L A T I O N
C A N B E K E P T 3 "
F R O M A L L S I D E S O F
F I X T U R E
Catalog #
Project
Comments
Type
Prepared by
Date
ADV110471
3/11/11
H o u s i n g
Formed of CRS with powder
coat finish.
P l a s t e r F r a m e
• Galvanized steel die-formed
construction.
• The housing can be removed
from plaster frame to provide
access to the junction box.
• Plaster frame features include:
- Patented regressed locking
screw positioned for
securing hanger bars
from below the ceiling.
- Cutouts for easily crimping
hanger bars in position.
- AIR-TITE aperture gasket is
pre-installed.
- HALO identity embossed on
plaster frame
S L I D E - N - S I D E ™ J u n c t i o n
B o x
• Positioned to accommodate
straight conduit runs
• Four 1/2” trade size conduit
knockouts with true pry-out
slots
• Slide-N-Side wire traps allow
non-metallic sheathed cable to
be installed without tools and
without removing knockouts.
• Accepts a wide range of
non-metallic (type NM)
sheathed cables - the standard
cable types used in lighting in
both U.S. and Canada.
- Allows wiring connections to
be made outside the junction
box.
- Simply insert the cable
directly into the trap after
connections are made.
- Accommodates the following
standard non-metallic
sheathed cable sizes:
(US) #14/2, #14/3, #12/2, #12/3
(Canada) #14/2, #14/3, #12/2
“ Q u i c k C o n n e c t ”
C o n n e c t o r s
Three quick connect wiring
connectors included.
G O T N A I L ! P a s s - N -
T h r u ™ B a r H a n g e r s
• Pre-installed nail easily installs in
regular lumber, engineered
lumber and laminated beams.
• Safety and guidance system
prevents snagging, ensures
smooth straight nail penetration
and allows bar hangers to be
easily removed if necessary.
• Automatic levelling flange aligns
the housing and lets you hold
the housing in place with one
hand while driving nails.
• Housing can be positioned at
any point within 24” joist span.
• Pass-N-Thru™ feature allows
bar hangers to be shortened
without removing from plaster
frame.
• Score lines allow “tooless”
shortening for 12” joists.
• Bar hangers may be
repositioned 90°.
• Integral T-bar clip snaps onto
T-bars - no additional clips
required.
S o c k e t
GU5.3 socket with reflector plate
for bi-pin 12V MR-16 lamps.
T r a n s f o r m e r
Integral 120V magnetic
transformer steps line voltage
down to lamp operating voltage.
For lamps up to 50W.
T h e r m a l P r o t e c t o r
Thermal protector deactivates
fixture if overheating occurs due
to improper lamping or
misapplied insulation.
L a b e l s
• UL/cUL Listed 1598 Luminaire
• UL/cUL Listed for Damp
Location
• UL/cUL Listed for Wet
Location, covered ceiling -
with select trims
• UL/cUL listed for Feed
Through
• Certified Under ASTM-E283 for
air tight construction
• IP rated (Improper Lamp)
Transformer Data:
Primary: 120VAC, 60Hz
Secondary: 11.5V±0.3V, 50VA
Insulation system: Class H
Nominal Amps with 50 watt,
12V rated Lamp: 0.50A
Nominal Watts with 50 watt,
12V rated Lamp: 57W
Slide-N-Side
™
Pass-N-Thru
™
Pass-N-Thru
™
™