Installation Sheet

ManualsBrandsEaton Lighting ManualsSure-LitesSure-Lites 7-7/8" Wide LED Outdoor Wet Location Emergency Light with Eagle Eye Self Diagnostics

Installation Instructions for the Sure-Lites SELW25 Emergency Light

WARNING

Risk of Fire / Electric Shock

If not qualiﬁ ed, consult an electrician.

Important Safeguards

When using electrical equipment, basic safety precautions

should always be observed including the following:

• READ AND FOLLOW ALL SAFETY INSTRUCTIONS

• Do not use in hazardous locations, or near gas or elec-

tric heaters.

• Do not let power supply cords touch hot surfaces.

• Use caution when servicing batteries. Battery acid can

cause burns to skin and eyes. If acid is spilled on skin

or in eyes, ﬂ ush acid with fresh water and contact a

physician immediately.

• Do not use this equipment for other than the intended

use.

• Installation is to be performed only by qualiﬁ ed person-

nel.

• Install in accordance with National Electric Code and

local regulatory agency requirements.

• The use of accessory equipment not recommended by

the manufacturer may cause an unsafe condition.

• Equipment should be mounted in locations and at

heights where it will not readily be subjected to tamper-

ing by unauthorized personnel.

• SAVE THESE INSTRUCTIONS

WARNING

Risk of Electric Shock

Disconnect power at fuse or circuit breaker before installing

or servicing.

INSTALLATION

1. De-energize the circuit at the junction box (J-box)

where the emergency light is to be installed.

2. Open the emergency light by inserting a ﬂ at screw-

driver in the two slots on the side of the unit, then

turning to separate housing from the backplate.

3. To mount to a junction box - Drill out the appropriate

mounting pattern and the wire pass hole in the back-

plate and the back gasket to ﬁ t the J-box being used.

4. To mount to conduit – Unscrew the ½” NPT plug locat-

ed at the top of the ﬁ xture and screw in the user-sup-

plied conduit hub.

5. Once the backplate is secured, the housing can be

held in place during installation with the help of the two

plastic strips (see Fig. 1 next page).

6. Connect the incoming wires to the SELW25 power

supply wires using the wire nuts provided. Connect the

white wire to neutral. If using 120V, connect the black

wire to the hot lead. If using 277V, connect the orange

wire to the hot lead. Cap the unused lead. Secure the

emergency light to the wall and/or junction box using

installer supplied hardware.

7. Complete the battery connection and snap the cover

onto the backplate.

8. Energize AC supply. The test button should illuminate,

and LED heads will illuminate brieﬂ y when the test

button is pushed.

9. Adjust the heads as needed. The SELW25 lenses

utilize a highly directional beam, and the lenses can be

rotated to adjust the beams to the front or sides of the

ﬁ xture (see Fig. 2 next page).

Sure-Lites

049-281

Summary of content (2 pages)

PAGE 1
Sure-Lites 049-281 Installation Instructions for the Sure-Lites SELW25 Emergency Light WARNING WARNING Risk of Fire / Electric Shock If not qualified, consult an electrician. Risk of Electric Shock Disconnect power at fuse or circuit breaker before installing or servicing. Important Safeguards INSTALLATION When using electrical equipment, basic safety precautions should always be observed including the following: 1.
PAGE 2
Figure 1 OPERATION Depress the test switch. The LED heads will light and the charge LED will extinguish. LED heads will illuminate as long as the button is pushed. Release the test switch. The charge LED will illuminate and the LED heads will turn off. FOR BEST RESULTS MOUNT WITH ARROW FACING UP MAINTENANCE: None required. Replace the batteries as needed according to ambient conditions. Equipment should be tested every 30 days in accordance with local codes.