Installation Sheet

ManualsBrandsEaton Lighting ManualsHaloHalo Convertible 7-3/4" Retrofit Recessed Light / Wall Sconce for 5" or 6" Housings with Cool White LED

SLD6 Series Instructions

SLD6 Instrucciónes Serie

SLD6 Directives Serie

Packaging Contents

Contenu de l’emballage

Contenidos del embalaje

ITEMS REQUIRED

(Purchase separately)

• #2PhilipsScrewdriver

• Gloves(ifusingfrictionblades)

ARTICLES NÉCESSAIRES

(à acheter séparément)

• Tournevisàtêtecruciformeno2

• Gants(sivousutilisezdeslames

defriction)

ARTÍCULOS NECESARIOS

(se compran por separado)

• DestornilladorPhilipsnº2

• Guantes(siseutilizalashojas

defricción)

B. Supply Wire Adapter (Required to be

installed onto ﬁxture per instructions)

Fil d’alimentation Adapater (à installer sur le

luminaire conformément aux instructions.)

El cable de suministro Adapater (deben

instalarse en la luminaria conforme a las

instrucciones.)

A. LED module and connector

Módulo LED y conector

Module DEL et connecteur

D. (2) Torsion Springs

(2) Resortes de torsión

(2) Ressorts de torsion

H. (3) Wire Nuts

(3) Noix de Fil

(3) Tuercas para Alambre

E. (2) Friction Clips

(2) Sujetadores de fricción

(2) Attachee de friction

F. E26 Edison screw base adapter

Adaptador de la base con

roscaEdison E26

L’adaptateur de base Edison E26

C. (2) #6-32 x 1 in. and (2) #8-32 x 1 in. junc-

tion box screws (use the size that ﬁts your

junction box)

(2) #8-32 x 1/4 in. self tapping screws

(2) Vis #6-32 x 1 et (2) #8-32 x 1 pour boîte

de jonction (utiliser la taille adaptée à votre

boîte de jonction)

(2) Vis de mécanique #8-32 x 1/4

(2) Tornillos #6-32 x 1 pulg. y (2) tornillos

#8-32 x 1 pulg. para montaje de la caja de

conexión (utilice el tamaño que mejor se

adecu a su caja de conexión)

(2) Tornillos mecánicos #8-32 x 1/4 pulg.

I. Connector

Conector

Connecteur

G. Green ground wire with #8-32 self tapping

screw and #8-32 hex nut

Mise á la terre vert avec vis de méca-nique

#8-32 et écrou hexagonal #8-32

Cable de conexión a tierra verde con

Tornillo mecánico #8-32 y tuerca hexagonal

#8-32

INS #

706087INST1

Summary of content (19 pages)

PAGE 1
INS # 706087INST1 SLD6 Series Instructions SLD6 Instrucciónes Serie SLD6 Directives Serie Packaging Contents Contenu de l’emballage Contenidos del embalaje B. Supply Wire Adapter (Required to be installed onto fixture per instructions) Fil d’alimentation Adapater (à installer sur le luminaire conformément aux instructions.) El cable de suministro Adapater (deben instalarse en la luminaria conforme a las instrucciones.) A. LED module and connector Módulo LED y conector Module DEL et connecteur E.
PAGE 2
706087INST1 IMPORTANT SAFETY INSTRUCTIONS When using product, basic precautions should always be followed, including the following: • Heed all warnings, including below warnings AND those included on product. • HALO recessed housings (fixtures) and retrofits are designed to meet the latest NEC requirements and are UL/cUL listed in full compliance with UL 1598. Before attempting installation of any recessed housing check your local electrical code.
PAGE 3
706087INST1 DETERMINING WHICH INSTALLATION METHOD TO USE This module can be mounted to recessed mounted standard junction boxes with junction box bracket or installed into 5 inch and 6 inch recessed housings with torsion spring receivers or with friction clips. WARNING Risk of electric shock. Disconnect power at fuse or circuit breaker before installing or servicing.
PAGE 4
706087INST1 The SLD6 is UL Listed or Classified for use with any 5 or 6 inch diameter recessed housing constructed of steel or aluminum with an internal volume that exceeds 107.9” in addition to those noted below.
PAGE 5
706087INST1 4. Arrange the supply wire adapter as shown in Figure 5A into the back of the junction box. 5. Align appropriate holes (Fig 4) in the mounting bracket with the holes in the junction box. Using 2 of the longer screws (either #6 or #8 screws depending on the size of the holes in your junction box) attach the mounting bracket to the junction box. Tighten screws until bracket is flush with the ceiling. Do not over-tighten screws or fixture will not be tight to ceiling (Fig. 5).
PAGE 6
706087INST1 Mounting to recessed housings For 6” housings with torsion spring receiving brackets (see HOUSINGS section of these instructions for a listing of the most common housings): 1. Locate the alignment arrow on the mounting bracket and the 6 inch arrow on the torsion spring clip and align the two marks Fig. 7). 2. Use one of the provided #8-32 x ¼ in. screws to attach the torsion spring bracket and the green ground wire to the mounting bracket (Fig. 7). 3.
PAGE 7
1 1 2 706087INST1 For 5” housings without torsion spring receiving brackets (see HOUSINGS section of these instructions for a listing of the most common housings): 1. Attach one of the friction mount clips to the innermost position on the mounting bracket using one of the provided #8-32 x ¼ in. screws (Fig. 10). 2. Repeat step 1 for the second clip but install the green ground wire under the screw. 1.
PAGE 8
706087INST1 MODULE INSTALLATION INTO E26 EDISON SCREW BASE RECESSED HOUSINGS INSTALLATION DU BOÎTIER DE Module POUR BOÎTIER AVEC CULOT À VIS EDISON E26. REMARQUE : Confirmez la compatibilité du boîtier NOTE: Confirm luminiare is compatible with SLD6 module series. A listing of the most common housings is avec le boîtier de module SLD6. Une liste des boîtiers provided in the HOUSINGS section of these instructions. les plus populaires est fournie au chapitre « BOÎTIERS » de ces instructions. 1.
PAGE 9
706087INST1 INSTALLATION INTO HALO LED (non-screw base) HOUSINGS H2750x, H550x and H750x SERIES NOTE: May be used to meet California Title 24, Washington State Energy Code, and International Energy Conservation Code High Efficacy Compliance. 1. Ensure bottom edge of housing is flush with ceiling. Adjust height if necessary to ensure a tight finish. 2. Install connector “I” (supplied) onto stripped wire ends of supply wire adapter (Fig 15a). Be sure to align black wire with black strip on connector.
PAGE 10
706087INST1 Cooper Lighting, LLC (“Cooper Lighting”) warrants to customers that, for a period of five years from the date of purchase, Halo SLD6 retrofit products will be free from defects in materials and workmanship. The obligation of Cooper Lighting under this warranty is expressly limited to the provision of replacement products. This warranty is extended only to the original purchaser of the product. A purchaser’s receipt or other proof of date of original purchase acceptable to Cooper Lighting.
PAGE 11
Cooper Lighting, LLC is not responsible for merchandise damaged in transit. Repaired or replaced products shall be subject to the terms of this warranty and are inspected when packed. Evident or concealed damage that is made in transit should be reported at once to the carrier making the delivery and a claim filed with them. Reproductions of this document without prior written approval of Cooper Lighting, LLC are strictly prohibited.
PAGE 12
706087INST1 - Retrofit Recessed Luminaire INS # SLD6 Series Instructions SLD6 Instrucciónes Serie SLD6 Directives Serie Packaging Contents Contenu de l’emballage Contenidos del embalaje B. Supply Wire Adapter (Required to be installed onto fixture per instructions) Fil d’alimentation Adapater (à installer sur le luminaire conformément aux instructions.) El cable de suministro Adapater (deben instalarse en la luminaria conforme a las instrucciones.) A.
PAGE 13
706087INST1 ITEMS REQUIRED ARTICLES NÉCESSAIRES ARTÍCULOS NECESARIOS (Purchase separately) • #2 Philips Screwdriver • Gloves (if using friction blades) (à acheter séparément) • Tournevis à tête cruciforme no 2 • Gants (si vous utilisez des lames de friction) (se compran por separado) • Destornillador Philips nº 2 • Guantes (si se utiliza las hojas de fricción) IMPORTANT SAFETY INSTRUCTIONS IMPORTANTES INSTRUCTIONS DE SÉCURITÉ INSTRUCCIONES IMPORTANTES DE SEGURIDAD When using product, basic precaut
PAGE 14
706087INST1 DIMMING Halo SLD is designed for dimming with many 120V Leading Edge (LE) and Trailing Edge (TE) phase control dimmers. Dimming capability may be enhanced with select dimmers that feature low end trim adjustment. (Consult dimmer manufacturer for specific load compatibility and application information. (Note some dimmers require a neutral in the wallbox.) For the latest Halo SLD product information, please refer to specifications online at www.cooperlighting.com.
PAGE 15
706087INST1 Mounting to recessed luminaires For 6” luminaire with torsion spring receiving brackets (see LUMINAIRES section of these instructions for a listing of the most common luminaire): 1. Locate the alignment arrow on the mounting bracket and the 6 inch arrow on the torsion spring clip and align the two marks Fig. 1). 2. Use one of the provided #8-32 x ¼ in. screws to attach the torsion spring bracket and the green ground wire to the mounting bracket (Fig. 1). 3.
PAGE 16
1 1 2 706087INST1 For 5” luminaire without torsion spring receiving brackets (see LUMINAIRES section of these instructions for a listing of the most common luminaire): 1. Attach one of the friction mount clips to the innermost position on the mounting bracket using one of the provided #8-32 x ¼ in. screws (Fig. 4). 2. Repeat step 1 for the second clip but install the green ground wire under the screw.
PAGE 17
706087INST1 RETROFIT INSTALLATION INTO E26 EDISON SCREW BASE RECESSED LUMINAIRES INSTALLATION DU BOÎTIER DE INSTALACIÓN DE LÁMPARA RETROFIT POSTCÂBLAGE POUR LUMINAIRE AVEC EN LUMINARIAS EMPOTRADAS CON CULOT À VIS EDISON E26. BASE ATORNILLABLE EDISON E26 REMARQUE : Confirmez la compatibilité du luminaire avec le boîtier de postcâblage SLD6. Une liste des luminaires les plus populaires est fournie au chapitre « LUMINAIRES » de ces instructions.
PAGE 18
706087INST1 REPLACING SLD6 Recessed Housing 1. With fingertips, pull down firmly on trim ring until retrofit series is removed from the housing. 2. Squeeze torsion springs together to remove LED retrofit series. If using friction blades, pull retrofit series out of housing slowly. 3. Disconnect LED retrofit series wiring from recessed luminaire. (LED connector or screw-in Edison base). 5-YEAR LIMITED WARRANTY REMPLACEMENT SLD6 Boîtier encastré 1.
PAGE 19
To obtain warranty service, please contact Cooper Lighting, LLC, at 1-800-334-6871, press option 2 for Customer Service, or via e-mail ConsumerProducts@ cooperlighting.com and include the following information: • Name, address and telephone number • Date and place of purchase • Catalog and quantity purchase • Detailed description of problem All returned products must be accompanied by a Return Goods Authorization Number issued by the Company and must be returned freight prepaid.