Datasheet

ManualsBrandsEaton Manualselectrical equipment & supplies68501

Entreprise Networks

Telecom

Process and infrastructures

Redundancy for highly critical applications.

www.mgeups.com

Can be built in to high density racks.

Single phase UPS

Pulsar MX

4/5/8/10/15/20 kVA

Continuous power supply

◗ Two front access hot-swappables

sub-modules (power and battery)

for maintenance without load

interruption.

◗ Automatic battery test (test period

can be set).

◗ Internal bypass built-in to supply the

load even if the UPS fails.

◗ Large input voltage and frequency

ranges to avoid using the batteries

unnecessarily.

Flexible

◗ Can be used as a free-standing tower

unit or 19" rack-mounted: only 3U

for Pulsar MX 4000 and 5000,

16U for Pulsar MX Frame

◗ LCD multilingual display with mimic

and LEDs for rapid view of the UPS

status, diagnostics and event log

◗ Outputs: IEC 10A and 16A outlet

sockets and hardwired outputs

◗ Built-in Powershare system for remote

reboot of the equipment connected,

sequential start-up or load shedding

while operating from battery to

maintain the power to critical loads.

◗ Pulsar MX Frame is compatible with

three phase or single phase supplies.

◗ Backup time: 10 mins up to 2 hours

by adding 3U battery extension

modules.

Minimum total cost

of ownership (TCO)

◗ More power with an output

power factor of 0.9.

◗ When the power supply needs

to be upgraded, the Pulsar MX

4000 and 5000 can be paralleled

to provide 8 kVA or 10 kVA

using the ModularEasy kit:

without extra cost on the

initial purchase.

◗ Pulsar MX Frame is a modular

system with 5 kVA sub-modules

paralleled to provide up to 20 kVA

or 15 kVA with redundancy.

High performance UPS upgradeable

from 4 kVA to 20 kVA

Can be used for 20 to 110

servers, ideal for:

◗ departmental networks, servers

and workstations

Pulsar MX: 10 minutes

backup, tower/rack

mounting (3U), mimic,

LCD display.

Pulsar MX has 2 sub-modules

(power electronics and battery)

which are hot swappable.

Pulsar MX Frame 15

and 20 kVA tower

and rack-mounting (16U),

modular system with

5 kVA sub-modules.

Paralleling 2 Pulsar MXs

using ModularEasy for 2N

or N+1 redundancy.

The power level can be upgraded simply and without

interruption for the existing loads as the number

of loads supplied is increased.

PULMX515UK.qxd 16/02/06 15:13 Page 1

Summary of content (2 pages)

PAGE 1
PULMX515UK.qxd 16/02/06 15:13 Page 1 www.mgeups.com Entreprise Networks Telecom Process and infrastructures Single phase UPS Pulsar MX 4/5/8/10/15/20 kVA Can be used for 20 to 110 servers, ideal for: High performance UPS upgradeable from 4 kVA to 20 kVA ◗ departmental networks, servers and workstations Continuous power supply ◗ Two front access hot-swappables sub-modules (power and battery) for maintenance without load interruption. ◗ Automatic battery test (test period can be set).
PAGE 2
PULMX515UK.qxd 16/02/06 15:13 Page 2 Single phase UPS - Pulsar MX Communications 8 IEC 10A outlet sockets Retention clips ◗ Solution Pac 2 suite supplied for remote 2 IEC 16A outlet sockets supervision. Output circuit protection ◗ MGE's Enterprise Power Manager for supervision 1 minislot for NMC, Modbus/JBus or MC Contacts/Serial card via Ethernet and Teleservice. EPM is compatible with standard network management systems (Tivoli, CA unicenter, HP Openview).