Specification

ManualsBrandsEaton ManualsDimmersAspire 600-Watt 120-Volt 60 Hz Single-Pole and Multi-Location Smart Dimmer, Desert Sand

CORE Lighting Controls

PART 1 – GENERAL

1.01 SUMMARY

A. Scope: Includes ASPIRE switches, dimmers, fan speed control and related devices as specified herein for the areas

indicated on the drawings, specifications, and load schedules.

B. Related Sections: Section 16570 (Dimming Controls).

1.02 REFERENCES

A. UL 1472

B. CSA

C. NOM

D. ANSI

E. FCC Part 15, Class B

1.03 SYSTEM DESCRIPTION AND OPERATION

A. Permanently installed, wallbox mounted switches, dimmers and accessories (remote units)

B. Permanently installed, wallbox mounted fan-speed controls

C. Permanently installed, wallbox mounted receptacles

D. Permanently installed, wallbox mounted data, voice and cable jacks

E. Screwless wallplates

1.04 SUBMITTALS

A. Submit manufacturer's standard catalog data giving all product, application, wiring, and installation information on all

basic components and wallplate kits. Provide test data and/or samples as required to demonstrate conformance with

PART TWO of this specification.

1.05 QUALITY ASSURANCE

A. Manufacturer shall have a minimum of 15 years continuous experience in manufacturing wallbox dimming products.

B. Dimmers, switches and Fan-speed controls shall be UL listed, CSA and NOM approved specifically for each

required load (i.e., tungsten, halogen, incandescent, electronic low voltage transformer, magnetic low voltage

transformer, and fluorescent). Manufacturer shall provide file card or certificate upon request. Universal load-type

dimmers shall not be acceptable.

C. To assure compatibility, all dimming controls shall be obtained from a single source with complete responsibility

over all lighting controls, including accessory products.

1.06 WARRANTY

A. All devices shall be covered by a minimum two-year warranty.

PART 2 – PRODUCTS

2.01 ACCEPTABLE MANUFACTURERS

A. Cooper Wiring Devices

B. Unless otherwise noted, all basic components (dimmer, fan-speed control, switch, accessory units, receptacle, and

communication outlets) shall be provided by one manufacturer.

Project Name:

Prepared By:

Project Number:

Date:

ASPIRE

Specification

Submittal

Catalog Number:

Type:

| w w w.co r e l i g h t i n g c o n t r o l s . c o m

Summary of content (5 pages)

PAGE 1
CORE Lighting Controls ASPIRETM Specification Submittal Project Name: Prepared By: Project Number: Date: Catalog Number: Type: PART 1 – GENERAL 1.01 SUMMARY A. Scope: Includes ASPIRE switches, dimmers, fan speed control and related devices as specified herein for the areas indicated on the drawings, specifications, and load schedules. B. Related Sections: Section 16570 (Dimming Controls). 1.02 REFERENCES A. UL 1472 B. CSA C. NOM D. ANSI E. FCC Part 15, Class B 1.
PAGE 2
CORE Lighting Controls 2.02 EQUIPMENT A. ASPIRE Lighting Controls 1. Performance a. Dimmers shall provide full-range, continuously variable control of light intensity. b. Wallbox mounted controls shall fit a decorator wallplate opening with a paddle switch. c. Controls shall have a two-tone color and/or finish (gloss or matte). d. Dimmer Controls shall provide both single-pole, 3-way control. e. Smart Dimmers shall provide multi-location control with up to 5 accessory dimmers. f.
PAGE 3
CORE Lighting Controls x. Controls shall meet the applicable requirements of UL 20 and UL 1472 referring to the inclusion of a visible, accessible air-gap off switch and the limited short circuit test. y. Controls shall meet ANSI/IEEE Std. C62.41-1980, tested to withstand voltage surges of up to 6000V and current surges of up to 200A without damage. z. Dimmers shall be designed to reduce interference with radio, audio, and video equipment. aa. Controls shall incorporate power-failure memory.
PAGE 4
CORE Lighting Controls 2. ASPIRE Receptacle Components a. All receptacles shall be UL Listed, CSA and NOM approved. b. Receptacles shall be two-pole, three wire ground and rated for 15A or 20A at 125VAC. All receptacles shall be NEMA configuration type 5-15R or 5-20R. c. Receptacles shall be available in single (9507TR, 9508TR) and duplex (9505TR, 9510TR) models. d.
PAGE 5
CORE Lighting Controls C. Devices shall be installed utilizing manufacturer’s recommended application, wiring and installation instructions. D. Contractor shall provide frameless wallplate covers per specification 2.02 for all devices ganged in a common box. Contractor shall provide barriers within the box where required by code. 3.02 FIELD QUALITY CONTROL A. Cooper Wiring Devices technical hotline available 8:00AM–6:00PM E.S.T. Monday–Friday: 1-866-853-4293 B.