Cut Sheet

Volume 1—Residential and Light Commercial CA08100002E—March 2015 www.eaton.com V1-T5-3
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5.2
Power Pedestals
Temporary Power/RV Park
Power Outlet Panels
Contents
Description Page
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . V1-T5-3
Application Description . . . . . . . . . . . . . . . . . . V1-T5-4
Features and Benefits . . . . . . . . . . . . . . . . . . . V1-T5-4
Standards and Certifications . . . . . . . . . . . . . . V1-T5-5
Catalog Number Selection. . . . . . . . . . . . . . . . V1-T5-6
Product Selection. . . . . . . . . . . . . . . . . . . . . . . V1-T5-7
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . V1-T5-7
Renewal Parts . . . . . . . . . . . . . . . . . . . . . . . . . V1-T5-8
Surface Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . V1-T5-10
Pedestal Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . V1-T5-16
Product Overview
A power outlet panel (or POP)
is a device designed for
outdoor service to meet
temporary power
requirements at construction
sites and RV parks. POPs
provide a safe and reliable
means for users to access
electricity at such locations.
Product Description
Power outlet panels shall be
designed for outdoor service
to meet temporary power
outlet requirements at
construction sites and provide
high quality, economical
power to individual sites
at RV parks. POPs shall be
provided with means to bond
the neutral for temporary
service entrance applications.
RV panels shall have a factory-
installed insulated neutral bar.
Receptacles and
Circuit Protection
Circuit protection shall be
Eaton’s UL listed full-size
Type BR or half-size Type BD
circuit breakers. The
receptacles shall be NEMA
commercial/industrial grade
devices. Ground fault
protection (GFCB) shall be
provided at the 20 A duplex
NEMA 5-20R receptacle or
20 A single-pole circuit
breaker when required.
Ground fault protection shall
be provided at the circuit
breaker for receptacles above
20 A when required.
Construction
The power outlet panel
pedestal shall be of deadfront
design and constructed of
heavy gauge, 100 percent
galvanized steel. Baked-on
polyester powder coating
shall be used for excellent
mechanical strength, plus
resistance to chalking caused
by the sun’s ultraviolet rays.
The power outlet panel
surface and pedestal units
shall have NEMA Type 3R
rainproof enclosures.
Ease of Installation
Panels shall ship from
the factory completely
assembled, prewired with
100 percent copper wire, and
tested in accordance with
UL Standard 231. The door
shall swing up and open for
user convenience and ease
of access to breakers and
receptacles. When required,
a means for securing the
door in the open position
shall be provided. Panels
shall be bottom fed through
knockouts in endwall or top
fed using a bolt-on raintight
hub. Knockouts shall range
from 1/2-inch (12.7 mm) to
1-1/2 inches (38.1 mm).
Grounding provisions
(#4–14 Cu/Al) shall be
provided on all panels.