Technical data

April 2008
16-16
For more information visit: www.eaton.com PG03300001E
Accessories & Modification Codes
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
Accessories
Advantage NEMA
Eaton’s Cutler-Hammer
®
Advantage
Control
Modules (ACMs) provide a
cost-effective alternative to push-
buttons, selector switches, indicating
lights, reset mechanisms, bell alarms
and panel meters when used with the
Advantage product line. Typical input/
output control functions provided by
panel mounted devices are conveniently
packaged in a series of modules
depending on application and
complexity.
Sixteen styles cover applications
ranging from:
■ Full voltage non-reversing
■ Full voltage reversing
■ Full voltage multispeed
■ Reduced voltage
■ DeviceNet compatible
Modules exist for each application to
provide the functions of:
■ Status only
❑ Indicating lights
❑ Reset
■ Status, START/STOP and RESET
■ Status, HOA and RESET
■ Status, START/STOP/HOA and
RESET
Full Voltage Pushbutton
Control Module
Metering Module
An additional Metering Module
replaces conventional ammeters
(three-phase), replaces reset mecha-
nisms and displays trip cause and
data, control voltage and status.
This Metering Module can be used
independently or in conjunction with
any of the ACMs. An extra plug con-
nection is available on the rear of each
ACM to accept the Metering Module
input.
The ACM family has been designed to
save:
■ Panel space (versus conventional
pushbuttons, selector switches and
indicating lights)
■ Mounting and assembly labor
■ Wiring and installation time
Regardless of the configuration, instal-
lation requires mounting only one 2.25
x 3.5 inch module, substantially reduc-
ing space requirements. Fitting a stan-
dard Greenlee punch and die set,
Greenlee #60071, installation is
accomplished with only two screws.
ACMs provide savings in wiring costs
as well. Regardless of the complexity
of the application, wiring is reduced to
a single plug-in cable, see photo at left.
Communication is not restricted by
use of the Advantage Control Mod-
ules. An extra plug connection is
available on the rear of the ACM or
Metering Module to allow a
WPONIDNA or WPONI Communica-
tions module to be plugged in.
Full Voltage and Reduced Voltage
Control Modules
Status Only
■ 4 LEDs indicate that the motor is
OFF, Running, Tripped or in Alarm
mode (motor current is above the
trip current setting)
■ Includes RESET button
START/STOP
■ Motor START/STOP controlled by
START and STOP buttons
■ Includes all features of Status Only
module
HOA Selector Switch with
START/STOP
■ In HAND mode, motor will start and
stop in response to START/STOP
pushbuttons
■ In AUTO mode, motor will run in
response to remote signal
■ Includes all features of Status Only
module
ON/OFF/AUTO Selector Switch
■ Motor will run in ON mode and not
in the OFF mode
■ In AUTO mode the motor will run in
response to a remote signal
■ Includes all features of Status Only
module
Reduced Voltage Control Modules
The four reduced voltage pushbutton
control modules provide control using
two to four starters and/or contactors.
The faceplates are identical to the full
voltage modules, and the pushbuttons
all perform the same functions. The
module is programmed for the type of
reduced voltage starter which sets the
sequence of contact open and closing.
Figure 16-11. Full Voltage and Reduced Voltage Control Modules
OL Alarm
Trip
OL Trip
OL Alarm
Trip
OL Trip
OL Alarm
Trip
OL Trip
RES
Reset
Run
Off
OL Alarm
Trip
OL Trip
RES
Reset
RES
Reset
RES
Reset
Run
Off
Run
HAND
START
STOP
START
STOP
OFF
AUTO
ON
OFF
AUTO
Off
Run
Off
Status Only
START/STOP
Control
HAND/OFF/AUTO Control
with START/STOP Pushbutton
Control in HAND Mode
ON/OFF/AUTO
Control
3.5
(88.9)
2.25 (57.2)