Cut Sheet

Volume 10—Enclosed Control CA08100012E—June 2015 www.eaton.com V10-T15-33
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15.1
Accessories and Modification Codes
Accessories
Auxiliary Contact Location for CN35/ECL
Auxiliary Contacts—Mounting Positions
The sketches below illustrate
the maximum number of
auxiliary contacts that can be
assembled to a contactor and
their locations in standard
enclosures.
Auxiliary Contact Mounting Positions
Auxiliary Contact Location
Size Poles
Available Mounting Positions
123
Open Type Type 1 Type 3R, 4X, 12
10A 2–4 T1, L1, R1 L1 L1, T1
20–60A 2–3 T1, L1 L1 L1, T1
60A 4 T1, L1 — L1, T1
60A 5 T1, L1 — L1, T1
100A 2–3 R2, R3, L1, L2, L3 R2, R3, L1, L2, L3 R2, R3, L1, L2, L3
200A 2–3 R2, R3, L1, L2, L3 R2, R3, L1, L2, L3 R2, R3, L1, L2, L3
300A 2–3 R2, R3, L1, L2, L3 R2, R3, L1, L2, L3 R2, R3, L1, L2, L3
400A 2–3 R2, R3, L1, L2, L3 R2, R3, L1, L2, L3 R2, R3, L1, L2, L3
L1
T1
L1
T1
R1
Front View
10–60A
Contactors
Top View
R1
100–400A
Contactors
Front
of Contactor
Left Side
of Contactor
L2
Aux.
Cont.
L3
Aux.
Cont.
R2
Aux.
Cont.
R3
Aux.
Cont.
L1
Base
Aux.
Cont.
R1
Base
Aux.
Cont.
Rear
Rear
Right Side
of Contactor
Pneumatic Timers—Top-Mounted for CN35/ECL
Attachment mounts on top of
10–60A lighting contactors
(top-mounted auxiliary
contacts cannot be installed
on device when timer is
used). Timer unit has DPST
timed contacts—circuits in
each pole must be the same
polarity. Units are convertible
from OFF to ON delay or vice-
versa.
Pneumatic Timers
Maximum Ampere Ratings
Solid-State Timers for CN35/ECL
Solid-State ON DELAY Timer—Side-Mounted on CN35 Freedom Series
Lighting Contactors Through 60A
This timer is designed to be
wired in SERIES with the
load (typically a coil). When
the START button is pushed
(power applied to timer), the
ON DELAY timing function
starts. At the completion of
the set timing period, timer
and series wired load will
both be energized.
Product Selection—Mounted Timer
Notes
1
Available positions on contactors or starters other than what is factory installed.
2
When a pneumatic timer is mounted on contactor, only side-mounted auxiliary contact
positions are available. The solid-state timer, when added, takes up side-mounted auxiliary
contact position.
3
For 100–400A contactors, a base auxiliary contact must be added in position L1 before
additional contacts can be mounted.
4
Add operating voltage suffix to catalog number. A = 120V, B = 240V, E = 208V.
5
Rated 0.5A pilot duty—not to be used on larger contactors.
6
Terminal connections are quick connects only. Two per side.
Timing Range Catalog Number
0.1–30 seconds C320TP1
10–180 seconds C320TP2
Description
Volts AC
120 240 480 600
Make 30.0 15.0 7.5 6.0
Break 3.0 1.5 0.75 0.6
Pneumatic Timer
Timing Range Catalog Number
456
0.1–1.0 seconds C320TDN1_
1–30 seconds C320TDN30_
30–300 seconds C320TDN300_
5–30 minutes C320TDN3000_
Solid-State Timer