Installation Guide

GENERAL INFORMATION
• For Indoor use only
• Technology: Passive Infrared (PIR)
RATINGS:
120VAC
• Incandescent/Tungsten – Max load: 6.7 Amps, 800W, 50/60 Hz
• Fluorescent Ballast – Max. load: 10 Amps, 1200W, 50/60 Hz
• Motor Load: ¼ HP
277VAC
• Fluorescent Ballast – Max. load: 9.8 Amps, 2700W, 50/60 Hz
SPECIFICATIONS:
• Compatible with Magnetic ballast or Electronic ballast
• The life of some fluorescent lamps may be shortened by frequent switching.
Compatibility should be verified with the fluorescent ballast manufacturer.
• No Minimum Load Requirements
• Coverage: Major Motion – 1,000 ft2
Minor Motion – 300 ft2
• Time Delay: Self Adjusting or Selectable 5,15, 30 minutes
• Light Level Sensing: 0 to 200 foot-candles
• Operating Temperature: 32 F to 104 F
• Operating Relative Humidity: 20% to 90 % non-condensing
• Mounting Strap Dimension: 4.20 inch x 1.73 inch
• Product Housing Dimension: 2.62 inch Long x 1.75 Wide x 1.90 Deep
• PIR Detection: Red LED
DESCRIPTION:
The OSP10 Occupancy Sensor is a Passive Infrared (PIR) motion sensing light-
ing control and conventional wall switch all in one.
INSTALLATION:
• When replacing a switch, choose a location that has clear line-of-sight
between the sensor and the area being controlled.
• Before installing or servicing the sensor, the power MUST be turned OFF at
the circuit breaker.
• The sensor should be installed according to National Electric Code and all
applicable local codes.
• The sensor should be wired according to the applicable wiring diagram
shown, using the wire connectors provided.
• Mount the device to the wallbox using the mounting screws provided, and
proceed with the setup process.
• After completing the set-up process install the wallplate.
SET-UP PROCESS
• Tools Required:
Small flat head screwdriver
General Explanation
After applying power to the device, wait 2 minutes for the sensor to power up
and stabilize before proceeding with the setup. All adjustment features and
mode selection switches are located under the main button. The button is re-
moved by releasing latches on either side of the button. DIP Switches are lo-
cated under the DIP Switch label.
Adjustments should be made with the HVAC system ON in order that the effects
of airflow on the sensor will be accounted for.
PIR Sensitivity Adjustment (DIP SW 5)
This adjustment is typically used to improve Major motion performance.
The Red LED will blink momentarily when the PIR sensor detects motion.
Default setting for DIP SW 5 is down. If the Red LED is constantly ON the sensi-
tivity can be reduced by 50% by moving DIP SW 5 up ().
Daylight Adjustment (Blue Dial)
• This feature prevents the lights from automatically turning ON when there is
sufficient natural lighting, regardless of whether the room is occupied.
• If this feature is not required the blue dial should be rotated fully clockwise.
• This adjustment must be done when the natural light level is at the level when
the lights should turn ON automatically.
• Place the device in Test Mode (refer below to TEST Mode).
• Rotate the Blue dial fully counterclockwise to Min.
• Immediately leave the area and observe that the lights turn OFF after 15
seconds.
• Return to the room. The lights should NOT automatically turn ON the lights.
• Rotate the blue dial clockwise in small increments, and pause for 5 seconds
after each adjustment, until the light turns ON. Take care to not block the
sensor from natural daylight while adjusting the blue dial. When the Light
turns ON, the adjustment is complete.
• The sensor will now prevent the lights from turning ON automatically for
any light level brighter than the calibrated light level.
NEXION PASSIVE INFRARED (PIR) SINGLE RELAY OCCUPANCY SENSING WALL SWITCH — OSP10
OSP10A-EN (REV. D)
ENGLISH
IN U.S.A.: Cooper Wiring Devices, 203 Cooper Circle, Peachtree City, GA 30269 • 866-853-4293
INSTINCT™
TECHNOLOGY
PASSIVE
INFRARED
A
Title 24
Compliant
RoHS
36’
8’
20’
15’
M
inor Motion, IR
M
ajor Motion, IR
Maximum coverage area may
vary somewhat according to room
shape and the presence of obstacles.
LOAD
HOT
BLACK
BLUE
NEUTRAL
GROUND
GREEN
WIRING DIAGRAM 1: SINGLE LEVEL
HOT
BLACK
BLUE
NEUTRAL
GROUND
GREEN
LOAD 1
LOAD 2
WIRING DIAGRAM 2: DUAL LEVEL WIRING USING A TOGGLE SWITCH