Powerware 5110 UPS User’s manual
©2005 Eaton Corporation All Rights Reserved The contents of this manual are the copyright of the publisher and may not be reproduced (even extracts) unless permission granted. Every care has been taken to ensure the accuracy of the information contained in this manual, but no liability can be accepted for any errors or omission. The right to make design modifications is reserved.
Powerware 5110 UPS User’s manual 1023922 Revision A Contents Introduction .................................................................................................4 Features: ................................................................................................................... 4 Unit inspection ......................................................................................................... 4 Requesting for CE-declaration .......................................................
Introduction The Powerware 5110 uninterruptible power system (UPS) filters the input line from line disturbances and protects your sensitive electronic equipment from five common power problems such as power failures, power sags, power surges, over-voltage and under- voltage.
Safety Instructions ATTENTION Maintenance, other than battery replacement must be performed by a qualified technician. Failure to do so could result in an electrical shock. Although the unit may be unplugged from utility power, hazardous voltage still may be present through the battery.” 1. Place the Powerware 5110 UPS indoors in an area that has adequate airflow and is free of excessive dust. Do NOT allow the UPS to be exposed to moisture, rain, excessive heat, or direct sunlight. 2.
Battery connection required before use! Connecting the Battery: Principal shown below for detailed information how to connect please refer to battery replacement section. Installation and Operation: Following steps explain how to connect and operate the Powerware 5110 UPS. 1. Connect the UPS to a grounded power outlet. 2. Plug your computer, monitor or load to be protected into the “Battery Backup & Surge Protection” outlets.
Typical applications Indicators 1. On/Off/Test Switch One switch controls power to your equipment and performs a self-test to detect overload/undercharge. Turn on the UPS. Press and hold the switch for more than one second and release the switch after the beep. The UPS will start. Turn off the UPS. Press and hold the switch for more than one second and release the switch. The UPS will shut down completely. Perform Self-test. The UPS will perform self-test for about 4.
2. Normal mode (Green)LED Indicates the UPS is providing mains power to your equipment. When the LED is blinking the UPS is providing power from the battery. 3. Fault (Red)LED When blinking, LED could indicate an overload condition or that the battery should be replaced. When the LED is always on it indicates a short or UPS fault. For details please see Indicator Table. 4. Battery mode (Yellow)LED Indicates the UPS is providing battery power to your equipment. 5.
Indicator table Status Indicators The UPS provides both visual and audible status indicators.
5Ah batteries (350VA, 500VA models) 7Ah x 1 battery (700VA models) 10 User’s manual 350 - 1500 VA 1023922 Revision A
7 Ah x 2 batteries (1000 VA models), 9 Ah x 2 batteries (1500 VA models) 1023922 Revision A User’s manual 350 - 1500 VA 11
Troubleshooting Symptom Possible Cause Action to Take UPS is not turned on or battery is not connected. Switch on the ON/OFF switch. If the power is not present, please make sure your circuit breaker on the building is not accidentally turned off. Circuit Breaker has tripped. Reduce the amount of equipment plugged into the “Battery Backup & Surge Protection” outlets of the UPS. Next, reset the circuit breaker by pushing it back in. The “Battery Backup & Surge Protection” outlets are overload.
Specification*: 230V Models Model 5110 350i USB 5110 500i USB 5110 700i USB 5110 1000i USB 5110 1500i USB Capacity 350VA / 210W 500VA / 300W 700VA / 420W 1000VA/ 600W 1500VA/ 900W Input Voltage Range 178~275Vac Output Voltage Range 207~250Vac Frequency 50 / 60 Hz auto sensing Outlets 4 Battery Backup & Surge Protection; 4 Surge Protection only Lighting / Surge Protection 476 Joules Transfer Time to Battery/AC 2-6 msec.
Service and Support For questions and/or problems, please call your local distributor or the help desk at one of the following telephone numbers and ask for a UPS technical representative. United States: 1.800.356.5737, Europe, Middle East, Africa: Local Powerware representative. Asia: +852.2830.3030, Australia: +61.3.9706.