Instruction Manual IM01005031E Instruction Manual IM01005031E Effective November 2012 Rev. 2 Effective March 2014 Eaton SPD SPD Series Series Eaton ForMounting MountingExternal ExternaltoTo for ElectricalDistribution DistributionEquipment Equipment Electrical Table of Contents 1.0 Introduction 2.0 Installation 3.0 Operating Features 4.0 Troubleshooting 5.0 Specifications 6.0 Ordering Guidelines 7.0 Warranty Rev.
Instruction Manual IM01005031E - Rev. 3 Effective March 2014 Eaton SPD Series for Mounting External to Electrical Distribution Equipment 1.0 Introduction WARNING 1.1 Manual Organization This Installation Manual describes the safe installation, testing and operation of the Eaton® SPD Series Surge Protective Device (SPD). This manual is organized into seven sections, as follows: 1.0 Introduction 2.0 Installation 3.0 Operating Features 4.0 Troubleshooting 5.0 Specifications 6.
Eaton SPD Series for Mounting External to Electrical Distribution Equipment Instruction Manual IM01005031E - Rev.3 Effective March 2014 1.5 Equipment Testing NOTICE WARNING CONDUCTING DIELECTRIC, MEGGER, OR HI-POTENTIAL TESTING WITH THE SPD INSTALLED WILL CAUSE INTERNAL DAMAGE TO THE SPD. THE SPD WILL ALSO CAUSE THE TEST TO FAIL. Every Eaton SPD Series unit is tested at the factory for dielectric breakdown. No further SPD testing is required for installation.
IM01005031E Rev.IM01005031E 2 Instruction Manual - Rev. 3 Effective 2012 EffectiveNovember March 2014 7. Determine the wire length for the Ground and Neutral (where applicable) wires and for cutthe these wiresand as Neutral needed.(where 7. Determine the wire length Ground Again, keep these as short possible to maximize applicable) wireswires and cut these as wires as needed. Again, keep SPDthese performance. wires as short as possible to maximize SPD performance.
Eaton EatonSPD SPD Series Series for Mounting External For Mounting ExternalToEquipment to Electrical Distribution Electrical Distribution Equipment Eaton SPD Series For Mounting ExternalTo Figure 3. NEMA 1 (Suffix K)) Electrical Distribution Equipment Figure 3. NEMA 1 (Suffix K) IM01005031E Rev. 2 Instruction Manual IM01005031E - Rev.3 Effective 2012 EffectiveNovember March 2014 IM01005031E Rev. 2 Effective November 2012 Figure 4. NEMA 4 - 4X (Suffix N, P) Figure3.4.
IM01005031E Rev. 2 Instruction Manual - Rev. 3 IM01005031E Rev.IM01005031E 2 Effective November 2012 Effective March 2014 Effective November 2012 Figure5.5.NEMA NEMA 1(With (WithDisconnect) Disconnect)(Suffix (SuffixM) M) Figure Figure 5. NEMA 11 (With Disconnect) (Suffix M) Figure 6. NEMA 4-4X (With Disconnect) (Suffix O, Q)) Figure 6. 6. NEMA NEMA 4-4X 4-4X (With (WithDisconnect) Disconnect)(Suffix (SuffixO, O,Q) Q) Figure 6 66 Eaton www.eaton.com eatoncorporation corporationwww.eaton.com www.eaton.
Eaton SPD Series for Mounting External to Electrical Distribution Equipment Instruction Manual IM01005031E - Rev.3 Effective March 2014 BLUE / WHITE COMMON RED / WHITE NORMALLY OPEN ORANGE / WHITE NORMALLY CLOSED Figure 7. Sidemount Form C Wires Figure 10. 3-Phase Wye Units * Figure 8. Split Phase Units *Contact Factory if High Leg is not on Phase B Figure 11. High Leg Delta Units Figure 9. 3-Phase Delta Eaton www.eaton.
Eaton SPD Series for Mounting External to Electrical Distribution Equipment Instruction Manual IM01005031E - Rev. 3 Effective March 2014 3.0 Operating Features 3.1 General The Eaton SPD Series comes in three feature packages: Basic, Standard, and Standard with Surge Counter. The operating specifics of each feature package are described below. The Eaton SPD Series requires no operator involvement, other than to monitor the display panel to determine status of the SPD.
Eaton SPD Series for Mounting External to Electrical Distribution Equipment Instruction Manual IM01005031E - Rev.3 Effective March 2014 3.2.2 Standard Feature Package 3.2.4 SPD Display Rotation The Eaton SPD Series Standard Feature Package display is shown in Figure 15. The SPD display can be rotated on the SPD enclosure, up to 360 degrees. This allows you to position the display for the best visibility regardless of the position in which the SPD is installed.
Instruction Manual IM01005031E - Rev. 3 Effective March 2014 Eaton SPD Series for Mounting External to Electrical Distribution Equipment 4.0 Troubleshooting Many SPD failures result from improper installation. Once the SPD is installed properly, it is a highly reliable unit. If the SPD does not function properly, first confirm that it is installed properly. See Section 2, “Installation.” If the SPD malfunctions after it has been operating routinely, refer to Table 2, Troubleshooting Chart.
Eaton SPD Series for Mounting External to Electrical Distribution Equipment Instruction Manual IM01005031E - Rev.3 Effective March 2014 5.0 Specifications Table 3.
Instruction Manual IM01005031E - Rev. 3 Effective March 2014 Eaton SPD Series for Mounting External to Electrical Distribution Equipment 6.0 Ordering Guidelines Table 4.
Eaton SPD Series for Mounting External to Electrical Distribution Equipment Instruction Manual IM01005031E - Rev.3 Effective March 2014 7.0 Warranty Eaton warrants these products for a period of 10 years from the date of delivery to the purchaser , 15 years if the product is properly registered with Eaton, to be free from defects in both workmanship and materials.
Instruction Manual IM01005031E - Rev. 3 Effective March 2014 Eaton SPD Series for Mounting External to Electrical Distribution Equipment Copyright © 2014 by Eaton, Moon Township, PA, USA. All rights reserved. No part of this document may be reproduced in any way without the express written approval of Eaton. Specifications contained herein are subject to change without notice.