Eaton® T2235 Series Automatic Transfer Switch (eATS) ePDU® Installation, Operations, and Maintenance Guide
Eaton and ePDU are registered trademarks of Eaton Corporation or its subsidiaries and affiliates. All other trademarks are property of their respective companies. ©Copyright 2009–2011 Eaton Corporation, Raleigh NC, USA. All rights reserved. No part of this document may be reproduced in any way without the express written approval of Eaton Corporation.
Special Symbols The following are examples of symbols used on the UPS or accessories to alert you to important information: RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of electric shock symbol. CAUTION: REFER TO OPERATOR'S MANUAL - Refer to your operator's manual for additional information, such as important operating and maintenance instructions. This symbol indicates that you should not discard waste electrical or electronic equipment (WEEE) in the trash.
Table of Contents 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dimensions . . . . . . . . . . . .
Table of Contents ii Eaton T2235 Series eATS ePDUs P-164000014—Rev 1 www.eaton.
Chapter 1 Introduction Eaton® T2235 Series Automatic Transfer Switches (eATS) are Enclosure Power Distribution Units (ePDU®) that provide distribution of primary power to controlled devices. They are specially designed for switching non-phase synchronized AC power sources. The intelligent circuitry in a T2235 Series eATS ePDU monitors both primary and secondary power inputs. If there is a problem with the primary power source, the eATS ePDU automatically transfers to the secondary power source.
Introduction Dimensions The T2235 Series eATS ePDUs are designed to mount in a standard 19-inch equipment rack with the following typical chassis dimensions: l 482.6 mm (19.0”) wide l 44.5 mm (1.75”) high l 177.8–24.3 mm (7.0–9.5”) deep NOTE There is currently one height exception. One custom-built T2235 Series eATS ePDU model with two rows of outlets (16 receptacles) is available. This model is 86.4 mm (3.4”) high.
Introduction Benefits The benefits of the T2235 Series eATS ePDUs are as follows: l l l l Provides dual power inputs and automatically selects the input source best suited to power-critical equipment. Meets Agency relay spacing requirements for out-of-phase switching up to 30A, while still performing fast enough to minimize transfer time. Provides power redundancy to equipment with one or two power supplies.
Introduction 4 Eaton T2235 Series eATS ePDUs P-164000014—Rev 1 www.eaton.
Chapter 2 Safety IMPORTANT SAFETY INSTRUCTIONS — SAVE THESE INSTRUCTIONS This manual contains important instructions that you should follow during installation and maintenance of the Eaton Automatic Transfer Switch (eATS) Enclosure Power Distribution Unit (ePDU) models. Please read all instructions before operating the equipment and save this manual for future reference. DANGER This ePDU contains LETHAL VOLTAGES. All repairs and service should be performed by AUTHORIZED SERVICE PERSONNEL ONLY.
Safety ATTENTION! l l l l Pour réduire les risques d'incendie et de décharge électrique, installer la ePDU uniquement à l'intérieur, dans un lieu dépourvu de matériaux conducteurs, où la température et l'humidité ambiantes sont contrôlées. La température ambiante ne doit pas dépasser 45 °C. Ne pas utiliser à proximité d'eau ou dans une atmosphère excessivement humide (95 % maximum).
Safety Advertencias de Seguridad INSTRUCCIONES DE SEGURIDAD IMPORTANTES — GUARDE ESTAS INSTRUCCIONES Este manual contiene instrucciones importantes que debe seguir durante la instalación y el funcionamiento de la ePDU. Por favor, lea todas las instrucciones antes de poner en funcionamiento el equipo y guarde este manual para referencia en el futuro. PELIGRO Este ePDU contiene VOLTAJES MORTALES.
Safety 8 Eaton T2235 Series eATS ePDUs P-164000014—Rev 1 www.eaton.
Chapter 3 Installation The Eaton T2235 Series Automatic Transfer Switch (eATS) Enclosure Power Distribution Unit (ePDU) models have a 19” chassis composed of 16 gauge (Ga.), electrolytic galvanized (EG) or cold roll (CR) steel plate. The T2235 Series eATS ePDU can be mounted on a rack or in a cabinet that accepts standard 19” width spacing. The ePDUs are installed in a 1U orientation. Installation of a T2235 Series eATS ePDU is to be performed by qualified, trained technicians.
Installation KIT-CABLRES-03 Universal Cable Restraint System The following parts for installing the optional cable restraint tray are located in the KIT-CABLRES-03 shipping carton: l (1) Cable management tray (001-2211-2) l (2) Mounting brackets (001-2233-2) l (11) 6-32 X 1/4” black screws (035-1606) l (12) Tie-wraps, 8” (010-0008) Before You Install Consider where you will locate the T2235 Series eATS ePDU model. These models are typically mounted at the bottom or rear of the equipment cabinet.
Installation Figure 4 shows an example cable restraint tray installed on an eATS ePDU in a rack. J3 J2 J1 Y AR ND CO SE Y AR IM PR Figure 4. Cable Restraint Tray Installation Installing the T2235 Series eATS ePDU CAUTION For PLUGGABLE EQUIPMENT, the power outlet you intend to use must be near the equipment and readily accessible. CAUTION Confirm that the equipment connected to the ePDU does not exceed the ePDU's capacity.
Installation ! IMPORTANT The ePDUs have two separate receptacle groups. The ePDU segments are protected separately by circuit breakers on the front panel. To install the ePDU: 1. If optional circuit breakers are installed, verify that each circuit breaker on the ePDU is in the OFF position. The indicator LED should be off. 2. Plug the equipment power cords into the ePDU output receptacles. Distribute the load evenly between the segments. 3.
Installation Branch Circuit Protection Caution Circuit breakers are not provided on all models; breakers are optional.
Installation 14 Eaton T2235 Series eATS ePDUs P-164000014—Rev 1 www.eaton.
Chapter 4 Operation This chapter describes operation of Eaton T2235 Series Automatic Transfer Switch (eATS) Enclosure Power Distribution Unit (ePDU) models, including the following: l Indicators, circuit breakers, and power outlets l Auto-transfer of primary input power to secondary input power l Electromagnetic interference/radio frequency interference (EMI/RFI) filtering option l Surge suppression Indicators The T2235 Series eATS ePDU models use six LED indicators to convey the following: l Indi
Operation Circuit Breakers Circuit breakers protect the power controller and all devices connected to it from fault conditions, such as a short circuit or an overload. Circuit breakers are optional for ePDUs with less than 30A input. However, circuit breakers are mandatory for ePDUs with 30A input or greater. ! IMPORTANT If a supplementary protector is used in the ePDU instead of a listed circuit breaker, additional branch circuit protection is required down-line from the power source to the ePDU.
Operation Figure 6 shows the EMI Filtering diagram. Line Load Figure 6. Filtering Diagram Surge Suppression Some T2235 Series eATS ePDU models provide line-to-neutral metal oxide varistors (MOVs), and some models provide line-to-line MOVs as delivered from the factory. See Chapter 6, “Specifications” on page 21 for more information. Table 4 shows specification data for Surge Protection Devices (SPD), formerly referred to as Transient Voltage Surge Suppressors (TVSS). Table 4.
Operation 18 Eaton T2235 Series eATS ePDUs P-164000014—Rev 1 www.eaton.
Chapter 5 Maintenance The Eaton T2235 Series Automatic Transfer Switches (eATS) Enclosure Power Distribution Unit (ePDU) models are constructed of high quality components and can be expected to provide trouble-free performance for extended periods. No adjustment or alignment procedures are required. Maintenance of the T2235 Series eATS ePDUs should be performed by qualified, trained technicians. Preventive Maintenance No periodic maintenance is required.
Maintenance 20 Eaton T2235 Series eATS ePDUs P-164000014—Rev 1 www.eaton.
Chapter 6 Specifications This chapter lists specifications that are applicable for all Eaton T2235 Series Automatic Transfer Switch (eATS) Enclosure Power Distribution Unit (ePDU) models. This chapter also describes online access to detailed model specifications, mechanical engineering diagrams, and additional documentation, such as product feature, options, and support.
Specifications Safety Standards Most of the Eaton T2235 Series eATS ePDU are UL listed and have been tested and approved to U.S. and Canadian (Bi-National) Standard for Safety of Information Technology Equipment, CSA C22.2 No 60950 Third Edition, dated December 1, 2000. Online Specifications The Eaton ePDU Web site (www.eaton.com/ePDU) provides online access to technical specifications, mechanical engineering diagrams, product features, options, and support resources.
Specifications Country Selections (Optional) To select a country to access the EATON EPDU Main page in different languages (see Figure 8): 1. Select www.ePDU.com/country. The EATON EPDUS - COUNTRY SELECTION page displays. Figure 8. Country Selection 2. Select a country name in the drop-down list and click Go. 3. The EATON EPDU Main page displays (see Figure 9). NOTE The country name you select determines the language that displays on the Eaton ePDU Web site.
Specifications Viewing in the Main T2235 Series eATS ePDU Family Page To view the EATON EPDU Main page: 1. Select www.eaton.com/ePDU. The EATON EPDU Main page displays (see Figure 9). l l l To search for a specific T2235 product line or model, go to “Using the ePDU Product Part Number Search Wizard” on page 25. To create specific search criteria to search for T2235 products by specific qualities, go to “Using the ePDU Product Function Search Wizard” on page 26.
Specifications Using the ePDU Product Part Number Search Wizard To use the EPDU PRODUCT WIZARD to view T2235 Series eATS ePDU technical specifications online (see Figure 10): 1. From the EATON EPDU Main page under EPDU SEARCH WIZARDS, click the Eaton Part Number or Competitor Part Number radio button. 2. Enter a partial or complete part number in the ePDU Part Number Search field. The adjacent Search button name changes to Show results. Click the button to view the search results. NOTE 3.
Specifications Using the ePDU Product Function Search Wizard To use the EPDU PRODUCT WIZARD to view specifications online (see Figure 11): 1. From the EATON EPDU Main page under EPDU SEARCH WIZARDS, click the Search by function in the ePDU Product Wizard link. 2. Either accept the default or select a new value from the drop-down lists for the Input Plug, Output Receptacle, Power Rating, or Function. The screen redisplays with the ePDU models that match the search criteria. NOTE 3.
Specifications Using the ePDU Browse Feature To use the ePDU Browse Feature to view online specifications: 1. From the main ePDU page under the BROWSE EATON EPDUS list, click the Eaton Automatic Transfer Switches link (see Figure 12). The EATON EATS EPDUS main page displays. Figure 12. Eaton ePDU Browse Feature Selection Eaton T2235 Series eATS ePDUs P-164000014—Rev 1 www.eaton.
Specifications 2. From the EATON EATS EPDUS Main page, perform one of the following: l l Click the ePDU Product Wizard button. In the EPDU PRODUCT WIZARD window, enter search criteria to view a list of eATS ePDUs that meet that criteria (see Figure 11 on page 26). Click the Technical Specs tab to see a comprehensive list of all eATS ePDUs in the product line (see Figure 13). Figure 13. EATON EATS EPDUS Main Page 3. Browse the list for your selection.
Chapter 7 Service If you have any questions or problems with the Eaton Enclosure Power Distribution Unit (ePDU) Automatic Transfer Switches (eATS), call your Local Distributor or the Help Desk at one of the following telephone numbers and ask for an ePDU technical representative.
Service 30 Eaton T2235 Series eATS ePDUs P-164000014—Rev 1 www.eaton.
Chapter 8 Warranty Two-Year Limited Warranty (USA and Canada) Eaton Enclosure Power Distribution Units (ePDUs) WARRANTOR: The warrantor for the limited warranties set forth herein is Eaton Corporation, an Ohio Corporation Company (“Company”). RACKMOUNTED LIMITED WARRANTY: This limited warranty (this “Warranty”) applies only to the original End-user (the “End-user”) of any Eaton Rackmounted Power Distribution Units (the “Product”) purchased on or after June 1, 2004, and cannot be transferred.
Warranty Customer Service Engineer or Agent; (e) improper testing, operation, maintenance, adjustment or modification of any kind not authorized in writing by Company personnel or performed by an authorized Company Customer Service Engineer or Agent; or (f) use of the Product under other than normal operating conditions or in a manner inconsistent with the Product’s labels or instructions. This Warranty is not valid if the Product’s serial numbers have been removed or are illegible.
Warranty COSTS NOT RELATED TO WARRANTY: The End-user shall be invoiced for, and shall pay for, all services not expressly provided for by the terms of this Warranty, including without limitation, site calls involving an inspection that determines no corrective maintenance is required. Any costs for replacement equipment, installation, materials, freight charges, travel expenses or labor of Company representatives outside the terms of this Warranty will be borne by the End-user.
Warranty 34 Eaton T2235 Series eATS ePDUs P-164000014—Rev 1 www.eaton.
*blank part number blank rev* P-164000014 1