Users Manual

INSTRUCTIONS
Introduction
ERC112 Smart Controller
EU1254 Kinetic Switch
ERC112 smart controller can be controlled with EU1254 wireless
kinetic switch, no battery is needed during use. It has WiFi module
inside, so can be controlled remotely with mobile APP, and also can
use voice control with Amazon Alexa.
Controller Model：ERC112
Kinetic Switch：EU1254
Controller Voltage: AC100V-240V 50/60Hz
Rated Load: 500W
Wireless Communication： WiFi 2.4GHz & RF 902 MHz
Control distance : 50m(Outdoor) 30m（Indoor）
Sensitivity: -110dBm
Storage Capacity: Maximum 10 switch keys can be paired
Dimming controller dimensions: L44*W41*H107mm
Kinetic switch dimensions: L33*W16*H65mm (Excluding base plate)
Switch base plate dimensions: L44*W3*H107mm
Temperature: -15℃~ +45℃
Product parameters
Installation
1.Use the line cap to wire
as shown
1.Mount the base plate on the wire box or wall
2.Adhere the wireless kinetic switch to the base plate
APP download
This controller can use mobile APP for remote control. Search
“ Kinetic switch” in App Store or Google Play and download, or scan
below QR code to download.
Connect WiFi Method
2.Power on the controller , and confirm the indicator light flashes
qucikly (twice per second ).If the indicator light is not flashing
quickly, press and hold y about 10 seconds, the indicator pairing ke
light will flash from slowly stay on, release when the to pairing key
indicator light stay on. After 3 seconds,the indicator light will flash
quickly(twice per second),which means that controller is ready for
WiFi connection.
1.Use mobile phone to download the app and follow the prompts to
register your account in the app.
Clear Pairing
1.If you need to clear paring of switch and controller.You should
keep press the pairing key 1 seconds until the light changes 2
from blinking to steady light and then goes out.
Or click on the "Clear Pairing" button in the app.
2.After clearing the pairing, the kinetic switch will no
longer control the controller, but can be paired again.
3.Click the “+” in top right corner of APP, and then select button
“ ”.Single receiver controller
4.Then click “confirm indicator light rapidly blink” and enter
password of WiFi, it starts to connect. If the indicator light goes
off, which means APP connect successfully and you can find the
device in the home page of APP.
5.After the pairing with network, so can use APP to trun on/off light .
Also,you can use mobile app for remote control, timed control and
scene control.
6.If you need to replace the router, you need to delete all the devices
in the app, and then re-add each device to your account once in
the new router.
Confirm the in dicator light fla sh quickly
Pairing the t hree devices as cl ose as possible
ECHO
“Alexa,tu rn on/off bed room li ght”
“Alexa, bri ght bedroom ligh t”
1.In the Kinetic Switch APP, rename the controller devices, such as
bedroom lights.
2.Add the SmartLife skill in Alexa APP, and log in by using the
account and password of the Kinetic Switch APP.
3.Discover the device in the smart application selection in the Alexa
APP.
4.Now you can control and controller with voice.
Troubleshooting
1.WiFi connection failed
Troubleshooting method: Please confirm the indicator light is blink
rapidly (twice per second); If not blink rapidly, please set the
indicator light to blink rapidly according to connect WiFi method.
Let router, controller and mobile phone as close as possible
(within 5 meters)
2.The controller is off line in APP
Troubleshooting method: Maybe the number of the router
connection over the maximum. Usually, only 15 devices can be
connected with Common router, please upgrate router and close
devices not needed.
3.Controller can not work after power on
Troubleshooting method: If the loads exceed the rated current or
short circuit, the fuse may blow. Please check the loads if suitable.
EU1254 Kinetic Switch
2.Load the controller into the
wire box and use screw to fix
Controller
Ground
Red:
Input Line
Black:Out put Line
White:Neu tral Line
Pairing Method
1.Power on the dimming controller, and then keep pressing the
pairing key about 6 seconds, when the indicator light flash slowly
(flash 1 time per second), then release the key, and the controller
is ready for pairing.You can also click the “pairing” button in the
app to make device enter pairing mode.
2.At this time, press any button of the kinetic energy switch once (do
not press several times). If the indicator light if off, it means that
pairing is successful.
3.If need to pair with multiple switches, repeat the above procedure.
Please note one controller can be paired with maximum10 switches.
In some cases, you need to re-pair the controller and kinetic energy
switch. Methods as below.
Control Instructions
Dimming controller can be controlled by kinetic switch after paired:
Up key
Down Key
Turn on ligh t
Turn off ligh t
4.After paring, can press the kinetic energy switch to control
dimming controller.
Pairing Key
1.Long pres s pairing key 6 seco nds,
indicator l ight will flash slo wly
2.click any k ey of kinetic swit ch once
Common Pairing Method