Product Data Sheet 422 J/39H Product Data Sheet 422 J/39H The engineer's choice
Product Data Sheet 422 J/39H 422 J/39H INDEX 1 General ............................................................................................................................................................... 3 2 Mechanics .......................................................................................................................................................... 3 2.1 2.2 3 Operating Data ..............................................................................................
Product Data Sheet 422 J/39H 1 General Fan type Rotating direction looking at rotor Airflow direction Bearing system Mounting position - shaft 2 Mechanics 2.1 General Fan Counterclockwise Air outlet over struts Ball bearing Any Width Height Depth Mass Housing material Impeller material Max. torque when mounted across both mounting flanges Screw size 2.
Product Data Sheet 422 J/39H 3 Operating Data 3.1 Electrical Operating Data Measurement conditions: ∆p = 0: I: Features Voltage range Nominal voltage Power consumption Tolerance Current consumption Tolerance Speed Tolerance Normal air density = 1,2 kg/m3; Temperature 23°C +/ - 3°C; Motor axis horizontal; warm-up time before measuring 5 minutes (unless otherwise specified). In the intake and outlet area should not be any solid obstruction within 0,5 m. corresp.
Product Data Sheet 422 J/39H 3.2 Electrical Interface - Output Alarm type Features Alarm operating voltage Alarm signal Low Alarm signal High Maximum sink current Leakage current /39 (low = ok, open collector) Note UBA UA low UA high Isink External resistor Alarm start-up delay time Alarm trip speed limit Alarm at sense failure Alarm latch Alarm isolated from motor 3.3 t6 nG Values <= 15 V I sink: 2 mA <= 0,4 V I source: 0 mA <= 15 V <= 4 mA 20 uA External resistor Ra from UBA to UA required.
Product Data Sheet 422 J/39H First pulse t5 typical 0.7s (0.5 .. 1.0s) followed by t4. Afterwards cyclical t3/t4.
Product Data Sheet 422 J/39H 3.4 Aerodynamics Measurement conditions: Measured with a double chamber intake rig acc. to DIN EN ISO 5801. Normal air density = 1,2 kg/m3; Temperature 23°C +/ - 3°C; In the intake and outlet area should not be any solid obstruction within 0,5 m. Motor shaft horizontal. The information is only valid under the specified test conditions and may be changed by the installation conditions.
Product Data Sheet 422 J/39H 02/01/2019 page 8 of 12
Product Data Sheet 422 J/39H 3.5 Sound Data Measurement conditions: Sound pressure level: 1 meter distance between microphone and the air intake. Sound power level: Acc. to DIN 45635 part 38 (ISO 10302) Measured in a semianchoic chamber with a background noise level of Lp(A) < 5 dB(A) For further measurement conditions see chapter aerodynamics. a.) Operation condition: 17.
Product Data Sheet 422 J/39H storage / transportation Bump not in use IEC 60068-2-29 Shock spectrum Acceleration Duration Number of bumps (+X, -X, -Y, +Y, -Z, +Z) Total bumps stationary use Random vibration in use IEC 60068-2-64 Frequency range / ASD GRMS Axes of vibration Test duration stationary use Bump in use IEC 60068-2-29 Shock spectrum Acceleration Duration Number of bumps (+X, -X, -Y, +Y, -Z, +Z) Total bumps 02/01/2019 Bump half sine 18 G 6 ms 100 in each direction 600 Random vibration 2 3 5
Product Data Sheet 422 J/39H 5 Safety 5.1 Electrical Safety Dielectric strength DIN EN 60950 (VDE 0805) and DIN EN 60335 (VDE 0700) A.) Type test Measuring conditions: After 48h of storage at 95% R.H. and 25°C. No arcing or breakdown is allowed! All connections together to ground. B.) Routine test Measuring conditions: At indoor climate. No arcing or breakdown is allowed! All connections together to ground. Isolation resistance Measuring conditions: After 48h of storage at 95% R.H.
