www.ebodeelectronics.eu User Manual IPV58P2P Wi-Fi HD720P Waterproof Outdoor P2P IP Camera Before using this product, please read this document carefully and visit www.ebodeelectronics.eu for latest manual, Software and FAQ.
Contents of the kit: 1x IP Camera 1x Ethernet Cable 1x Power Adapter 1x Mounting Bracket + Screws 1x Resource CD 1x Wi-Fi Antenna U sers’ manual 1x Quick Start Guide 1x Surveillance Sticker 1x ebode leaflet Technical Specification: Full HD720P Waterproof IP Camera P2P Feature for Easy Remote Access H.
User Guide Table of Contents 1. Conformity of use…………………………………………………………………………………… 4 2. Introduction……………………………………………………………………………………………. 4 3. 3.1 3.2 3.3 Overview…………………………………………………………………………………………………. 5 Key Features…………………………………………………………………………………………… 5 Read Before Use……………………………………………………………………………………… 5 Physical Description…………………………………………………………………. ………… 6 4. Access the IP Camera…………………………………………………………………………….. 8 4.1 Access the Camera in LAN………………………………………………………. 8 4.
1. Conformity of Use For carefree and safe use of this product, please read this manual and safety information carefully and follow the instructions. The unit is registered as a device that does not cause or suffer from radio-frequency interference. It is CE approved and it conforms with the Low Voltage Directory. The safety and installation instructions must be observed. Technical manipulation of the product or any changes to the product are forbidden, due to security and approval issues.
3. Overview The outdoor HD IP Camera is integrated IP Camera with a color CMOS sensor enabling viewing in High Definition resolution. It combines a high quality digital video camera, with a powerful web server, to bring clear video to your desktop from anywhere on your local network or over the Internet. The IPCAM support the industry-standard H.264 compression technology, drastically reducing file sizes and conserving valuable network bandwidth.
3.3 Physical Description Front Panel Figure 3.1 1. 2. 3. 4. Infrared LED: Wireless Antenna. LENS: CMOS sensor with fixed focus lens. Induction IC. Infrared LED: 12 IR LEDs Interface Figure 3.
1. I/O alarm terminal block (Not available for this camera) This network camera provides a I/O alarm terminal block which is used to connect to external input / output device. The pin(there are four number in the terminal block from no. 1 to no. 4) definitions are as follows: 1.) input, 2). input, 3). output, 4). output. This camera supports I/O alarm, you can go to Settings-Alarm - I/O page to configure it. 2. LAN 10/100M adaptive Ethernet interface.
Figure 3.4 4. Access the IP Camera This chapter explains how to access the camera through browser and RTSP player. 4.1 Access the Camera in LAN This camera supports HTTP and HTTPS protocols, so here will allow you to use HTTP and HTTPS port No. 1). Http:// LAN IP + Http Port No. Double click the IP Camera Tool icon and it should find the camera’s IP address automatically after you plug in the network cable. Figure 4.
4.2 Access the Camera in WAN 4.2.1 Static IP Addresses Users who have static IP addresses do not need to set DDNS service settings for remote access. When you have finished connecting the camera using the LAN IP address and port forwarding, you can access the camera directly from the Internet using the WAN IP address and port number. How to Obtain the WAN IP address from a public website ? To obtain your WAN IP address enter the following URL in your browser: http://www.whatismyip.com.
Step 2: Wait around 10 seconds, you’ll see that the camera’s LAN IP address has changed. In our example it was changed to 2000, so we see http://192.168.8.102:2000 in IP Camera Tool. Also, the LAN IP address is now fixed at a static IP address of http://192.168.8.102:2000. This IP address will not change even if the camera is powered off and back on, the camera will remain on this LAN IP address.
Modify the Http Port. Enter username and password, click OK. Figure 4.6 Figure 4.7 What is Port forwarding? If you have never done port forwarding before, you can open and view the following link to understand the basic concept. Port forwarding allows for outside connections to access a specific device on your network from anywhere in the world. Every router automatically blocks any incoming connections for safety purposes.
Fill the HTTP Port of the camera in the columns of External Port and Internal Port. Example: 2000 Fill in this section with the LAN IP of the camera; we would enter “100” for our example. Assign a name for the port forward setting here . Figure 4.8 First method : Use the embedded DDNS to access the camera via the Internet Each camera has an embedded unique DDNS domain name, the format of this domain name is xxxxxx.myipcamera.org.
Second method : Use the Third party DDNS to access the camera via the Internet Step 1: Please go to the third party DDNS website(such as www.no-ip.com) to create a free hostname. Step 2: DO DDNS Service Settings within the Camera Please set DDNS Settings within the camera by hostname, a user name and password you’ve got from www.no-ip.com. Take hostname ycxgwp.no-ip.info, user name test, password test2012 for example. Firstly, goes to option of DDNS Settings on the administrator panel.
Figure 4.10 Figure 4.
Sometimes you may need to enter the user name and password again. Click OK and you can see the real-time preview. Figure 4.12 Figure 4.13 If you cannot play the video in the VLC player, please check the port mapping. You can read Quick Installation Guide about How to configure port forwarding. NOTE: If you modify the camera’s username or password, you had better reboot the camera, or else the new username and password cannot take effect when you enter the authentication in the VLC. 4.
5. Surveillance Software GUI Please refer to the Quick Installation Guide if you install the camera at first time. After finishing quick installation, you can take time to learn the operation of the software. 5.1 Login Window Figure 5.1 Please check the login window above, it was divided to 4 sections from no. 1 to 4. 1.
4. Login the camera Click Login button and you will see the surveillance windows.(If login the camera for the first time, the page that modify the username and password will appears.) 5.2 Modify the Username and Password When you log in for the first time, it will come to the operating of modify the username and password automatically. Figure 5.2 Enter the New Username, New password and Confirm the password. Click Modify button, you will see the login page again. 5.
1. LiveVideo / Settings buttons window Path to surveillance window. Click this button and back to the surveillance Path to Administrator Control Panel, Click it, and it will lead to Administrator Control Panel and do advanced settings. 2. Multi-Device Window The firmware supports up to maximum of 9 cameras being monitoring at the same time. You can add other cameras in multi-camera panel. Figure 5.4 3.
3) Maximum frame rate When the video format is 50Hz, the maximum frame rate is 25 fps. When the video format is 60Hz, the maximum frame rate is 30 fps. You should lower frame rate when the bandwidth is limited. Normally, when the frame rate above 15, you can achieve fluently video. 4) Bit rate Generally speaking, the larger the bit rate is, the clearer video will become. But the bit rate configuration should combine well with the network bandwidth.
1) 3) 5) 7) Up control button. Left control button. Up-Left control button. Down-Left control button. 2) 4) 6) 8) Down control button. Right control button. Up-Right control button. Down-Right control button. Click this button and go to center. 5. Cruise settings (Not available for this camera) If via RS485 interface to connect an external PT device, you can use this feature.
Click IR LED Lights and there are two modes to adjust the infrared led: Auto and Off . The default mode is Auto. Auto: Select it and the camera will adjust the infra led (on or off) automatically. Manual: Select it and turn off the infra led manually. Schedule: Select it and the IR led light will be off at the schedule period. If you want to define or change the IR led lights schedule time, please go to Settings Video IR LED Schedule page. 7.
1) Play: Click it to play the video of the camera 2) Stop: Click it to stop the video of the camera 3) Talk: Click the button and the icon will become to , then talk to the microphone that connected with PC, people around the camera can hear your voice if the camera has connected with audio output device. Click the icon again and stop talking.
Figure 5.7 NOTE: For Mac OS, the plugin cannot support Onscreen Mouse function, so you cannot allow to use it. 6. Advanced Camera Settings Click the button “Settings”, goes to Administrator Control Panel to make advanced camera settings. 6.1 Device Status Device Status contains four columns: Device Information, Device Status, Session Status and Log, it will show you various information about your camera. 6.1.1 Device Information Figure 6.
Camera Model: The model of the device. Camera Name: The Device Name is a unique name that you can give to your device to help you identify it. Click Basic Settings and go to Device Name panel where you can change your camera name. The default device name is anonymous. Camera ID: Display the MAC address of your camera. For example Device ID is 008414350787, the same MAC ID sticker is found at the bottom of the camera. Camera Time: The system time of the device.
Click the page number and go to the corresponding page to see more logs . Fill in one page number, click Go button and go to the corresponding page Figure 6.4 6.2 Basic Settings This section allows you to configure your Camera Name, Camera Time, Mail, User Accounts and Multi-Device. 6.2.1 Camera Name Default alias is anonymous. You can define a name for your camera here such as apple. Click Save to save your changes. The alias name cannot contain special characters. Figure 6.5 6.2.
Figure 6.6 Time Zone: Select the time zone for your region from the dropdown menu. Sync with NTP server: Network Time Protocol will synchronize your camera with an Internet time server. Choose the one that is closest to your camera. Sync with PC: Select this option to synchronize the date and time of the Network Camera with your computer. Manually: The administrator can enter the date and time manually. Please select the date and time format.
How to change the password? Firstly, select the account which you want to change the password, then select “Change password”, enter the old password and the new password, lastly click modify to take effect. Figure 6.8 How to add account ? Select one blank column, then enter the new user name, password and privilege, last click Add to take effect. You can see the new added account on the Account list. Figure 6.
Figure 6.10 Delete : Select the account which you want to delete, then click Delete button to take effect. NOTE: The default administrator account cannot be deleted, but you can add other administrator users. How to change the username ? Firstly, select the account which you want to change the username, then select “Change username”, enter the new password, lastly click modify to take effect. Figure 6.
6.2.4 Multi-Camera If you want to view multi-surveillance screens on one window, you need to login one camera, and set it as the main device, and do Multi-Device Settings, add other cameras to the first one camera. Before you do multi-cams settings, you need to assign different port such as 81, 82, 83, 84, 85, 86, 87, 88 to the cameras if there is 8 cams installed. The firmware within the camera can support a maximum of 9 devices monitoring all at the same time. This page you can both add IPCAM MJPEG and H.
Figure 6.13 Back to Surveillance Windows, and click Four Windows option, you will see four cameras you added. Figure 6.
Figure 6.15 Add cameras in WAN If you want to view all cameras via the internet(remote computer), you will need to add them using DDNS domain name. Firstly, make sure all of the cameras you added can be accessed through the internet. (Read How to configure DDNS settings in chapter 6.3.3) Login to the first camera using a DDNS domain name and port. Use DDNS domain name and port to login. Make sure each camera you need add could login with DDNS name and port. Figure 6.
Click Multi-Device Settings. Choose The 2nd Device. Fill in the 2nd camera’s name, DDNS domain name, port number. Enter user name and password and then choose Add. 1 2 3 4 5 Figure 6.17 1) 2) 3) 4) 5) The camera model: MJ or H264. The 2nd camera’s name Fill in the 2nd camera’s DDNS host not LAN IP Enter the 2nd camera’s user name and password Click Add button and to take effect NOTE: Here the Host must be entered as the second camera’s DDNS domain name, not its LAN IP.
Figure 6.18 Return to video window. You will see all of the cameras accessible through the internet. When you are away from home, you can use the first camera’s DDNS domain name and port to view all the cameras via internet. Figure 6.
6.3 Network This section will allow you to configure your camera’s IP, PPOE, DDNS, Wireless Settings, UPnP, Port, Mail Settings and FTP Settings. 6.3.1 IP Configuration If you want to set a static IP for the camera, please go to IP Configuration page. Keep the camera in the same subnet of your router or computer. Figure 6.20 Changing settings here is the same as using the IP Camera Tool. (Figure 4.23/4.24) It is recommended that you use the subnet mask, gateway and DNS server from your locally attached PC.
Set the same Subnet Mask and gateway of the camera with your PC. There are two DNS servers, you can set any of them. Same with gateway is also OK. Figure 6.22 If you don’t know the DNS server, you can use the same settings as the Default Gateway. 6.3.2 Wireless Settings Step 1: Choose “Settings” on the top of the camera interface, and go to the “Network” panel on the left side of the screen, then click “Wireless Settings.
Step 2: Click the SSID (name of your router) in the list, the corresponding information related to your network, such as the name and the encryption, will be filled into the relevant fields automatically. You will only need to fill in the password of your network. Make sure that the SSID, Encryption and the password you filled in are exactly the same for your router.
Figure 6.25 6.3.4 DDNS The camera has embedded a unique DDNS domain name when producing, and you can directly use the domain name, you can also use the third party domain name. IPCAM domain name Here take cp4911.myipcamera.org for example. Go to option of DDNS on the Settings>Network panel, you can see the domain name. Figure 6.26 Now you can use http:// Domain name + HTTP Port to access the camera via internet. Take hostname cp4911.myipcamera.org and HTTP Port no.
Third Party Domain Name Settings User can also use third part DDNS, such as www.no-ip.com. ,www. 3322.com. Here take www.no-ip.com for example: ① Step 1, Go to the website www.no-ip.com to create a free hostname Firstly: Login on www.no-ip.com and click No-IP Free to register. Click here to register Figure 6.27 Please register an account step by step according to instructions on www.no-ip.com After registration, please login your email which used to register.
Figure 6.28 Figure 6.29 Please create the domain name step by step according to instructions on www.no-ip.
Step 2 DO DDNS Service Settings within the Camera Please set DDNS Settings within the camera by hostname, a user name and password you’ve got from www.no-ip.com Take hostname ycxgwp.no-ip.info, user name test, password test2012 for example. Firstly, goes to option of DDNS Settings on the administrator panel. Secondly, select No-Ip as a server. Thirdly, fill test as DDNS user, fill password test2012 as DDNS password, fill ycxgwp.noip.info as DDNS domain and server URL, Then click save to make effect.
③ Use domain name to access the camera via internet After the port forwarding is finished, you can use the domain name+ http no. to access the camera via internet. Take hostname ycxgwp.no-ip.info and http no 2000 for example, the accessing link of the camera via internet would be http:// ycxgwp.no-ip.info:2000 6.3.5 UPnP Figure 6.31 The default UPnP status is closed. You can enable UPnP, then the camera’s software will be configured for port forwarding.
Another way to change the HTTP port no. Step 1: Open the IP Camera Tool, select the camera you would like to change the port of, right click on the IP address, and click on ”Network Configuration”, this brings up the network configuration box as shown in Figure 6.34 and 6.35. Select which camera you’d like to change the port for, and right click Figure 6.34 Enter the Modify the Username and Http Port. password, click OK. Figure 6.
Step 2: Enter the username and password of the Administrator (default username is admin with a blank password), and click “OK” to apply changes. Step 3: Wait around 10 seconds, you’ll see that the camera’s LAN IP address has changed. In our example it was changed to 2000, so we see http://192.168.8.102:2000 in IP Camera Tool. Also, the LAN IP address is now fixed at a static IP address of http://192.168.8.102:2000.
Figure 6.37 Figure 6.
Sometimes you may need to enter the user name and password again. Click OK and you can see the real-time preview. Figure 6.39 Figure 6.40 If you cannot play the video in the VLC player, please check the port mapping. You can read Quick Installation Guide about How to configure port forwarding. NOTE: If you modify the camera’s username or password, you had better reboot the camera, or else the new username and password cannot take effect when you enter the authentication in the VLC.
6.3.7 Mail Settings If you want the camera to send emails when motion has been detected, here Mail will need to be configured. 5 1 2 6 3 4 Figure 6.41 1) SMTP Server/ Port /Transport Layer Security: Enter SMTP server for sender. SMTP port is usually set as 25. Some SMTP servers have their own port, such as 587 or 465, and Transport Layer Security usually is None.
Test result Figure 6.42 If the test success, you can see the Success behind the Test, at the same time the receivers will receive a test mail. If the test fails with one of the following errors after clicking Test, verify that the information you entered is correct and again select Test. 1) Cannot connect to the server 2) Network Error. Please try later 3) Server Error 4) Incorrect user or password 5) The sender is denied by the server.
6.3.8 FTP Settings If you want to upload record images to your FTP server，you can set FTP Settings. Figure 6.43 Figure 6.44 FTP server: If your FTP server is located on the LAN, you can set as Figure 4.48. If you have an FTP server which you can access on the internet, you can set as Figure 6.49. Port: Default is port 21. If changed, external FTP client program must change the server connection port accordingly. FTP Mode: Here supports two modes: PORT and PASV.
Search and install the application named “ebode” on Google Play for Android devices, or on APP Store for iOS devices. If you want to know more details of the iOS APP or Android APP, see the iOS App User Manual or Android APP User Manual. 6.4 Video This section allows you to configure Video stream settings, On screen display and Snapshot settings. 6.4.1 Video Settings There are two ways to set the stream video settings. They are main stream video settings and sub stream video settings. Figure 6.
6.4.2 On Screen Display This page is used to add timestamp and device name on the video. Figure 6.47 Display Timestamp: There are two options: Yes or NO. Select Yes and you can see the system date on the video, Display Camera Name: There are two options: Yes or NO. Select Yes and you can see the device name on the video, 6.4.3 Privacy Zone This page is used to add privacy zone on the video. Figure 6.48 There are two options: Yes or NO.
Click OK button and return to the Privacy Zone page, click Save to take effect. Back to the surveillance window, you can see the privacy area as the following picture: Figure 6.50 6.4.4 Snapshot Settings On this page you can set the snapshot pictures’ image quality and the storage path. Figure 6.51 Image Quality: Low, Middle and High. The higher the quality, the picture will be clearer. Alarm Pictures Save Path: FTP.
Enable timing to capture To enable capture interval, follow the steps below: 1 Select Enable timing to capture 2 Capture interval: The interval time between two captures. 3 Select the capture time Capture any time Click the black button up the MON, you will see all time range turn red. When something moving in the detection area at any time, the camera will capture. Specify an capture schedule Click the week day words, the corresponding column will be selected.
6.5 Alarm 6.5.1 Motion Detection IP Camera supports Motion Detection Alarm, when the motion has been detected, it will send emails or upload images to FTP. Figure 6.54 To enable motion detection, follow the steps below: 1) Enable Motion detection 2) Sensitivity: It supports three modes: Low, Middle and High. The higher the sensitivity, the camera will be more easily alarmed. Select one motion sensitivity. 3) Trigger interval: The interval time between two motion detections.
There are three alarm indicators: A Camera Sound and PC Sound If the camera has connected with a speaker or other audio output device, if you select Camera Sound or PC Sound, when the motion has been detected, the people around the camera will hear beep alarm sound. B Send E-mail If you want to receive alarm emails when motion is detected, you must select Send Email and set Mail Settings first. The alarm email cannot contain the alarm picture if you have not selected Take Snapshot.
6) Alarm Schedule ① Alarm anytime when motion is detected Click the black button up the MON, you will see all time range turn red. When something moving in the detection area at any time, the camera will alarm. Click this button and select all time range Figure 6.57 ② Specify an alarm schedule Click the week day words, the corresponding column will be selected.
7) Click Save button to take effect. When the motion is detected during the detection time in the detection area, the camera will alarm and adopt the corresponding alarm indicators. NOTE: You must set the detection area and detection schedule, or else there is no alarm anywhere and anytime. 6.6 Record 6.6.1 Storage Location On this page you can change the manually recording storage path, the default storage path is D:\ipc. Figure 6.60 6.6.2 Alarm Recording Figure 6.61 6.6.
6.6.4 Scheduled Recording On this page you can enable schedule record. Figure 6.63 You can select the main stream or sub stream from the drop-down. You can set the store path of the recording file on the Storage Location page. Stream: You can select the main stream or sub stream from the drop-down. You can set the store path of the recording file on the Storage Location page. Click Save button to take effect. 6.
6.7.2 RS485 Configuration This camera supports the standard 485 cradle head protocol (PELCO-D and PELCO-P). Please configure the RS485 protocol corresponding information first, or else the cradle head may cannot work. Figure 6.65 6.8 Firewall This section explains how to control the access permission by checking the client PC’s IP addresses. It is composed of the following columns: Block access from these IP addresses and Only allow access from these IP addresses. Figure 6.
6.9 System In this panel, you can back-up / restore your camera settings, upgrade the firmware to the latest version, restore the camera to default settings and reboot the device. 6.9.1 Back-up & Restore Click Backup to save all the parameters you have set. These parameters will be stored in a bin file for future use. Click Browse and select the parameters file you have stored, then click Submit to restore the restore the parameters. Figure 6.67 6.9.
Figure 6.69 Enter the User name and password Figure 6.70 CAUTION: If your camera works well with the current firmware, we recommend not upgrading. Please don’t upgrade the firmware unnecessarily. Your camera may be damaged if misconfigured during an upgrade. NOTE: 1) Don’t upgrade the firmware through the web UI in WAN, or else the upgrade may fail. 2) Please ensure you have download the correct firmware package for your camera before upgrading. Read the upgrade documentation (readme.
6.9.3 Factory Reset Click Factory Reset button and all parameters will return to factory settings if selected. The default administrator username is admin with a blank password. Figure 6.71 6.9.4 Reboot Click Reboot to reboot the camera. This is similar to unplugging the power to the camera. Figure 6.72 7. Appendix 7.1 Frequently Asked Questions NOTE: Any questions you would meet, please check Network connections firstly.
Double click the plug-in to install it. Figure 7.2 Continue to finish the installation, and then it will be successful. Figure 7.3 Please check if the plug-in was successfully installed or not. Figure 7.4 Restart Safari to enable the plug-in.
7.1.2 How to download and install the ActiveX for Firefox users For the first time login the camera, it may prompt you to download plugin . Click here to download the plugin Figure 7.5 Drag the download file to Firefox web page and it will prompt you to Install it. Click Install Now Figure 7.6 Reboot the Firefox after the plugin installation is successfully completely, then re-login the camera again, you can see the surveillance window.
NOTE: If you could not view living video after running the ActiveX, only a red cross in the center of the video or just a black screen. Please change another port number to try. Make sure all firewall or antivirus software on your computer does not block the active download and installation. If you are unable to run the ActiveX control, try shutting down the firewall or antivirus program. 7.1.
Click Add button to install the Plugins. Click Add button to install the plugin Figure 7.9 Reboot the browser and re-login the camera, you will see the surveillance window. 7.1.4 I have forgotten the administrator password To reset the administrator password, you had better unplug the network cable firstly. After that, press and hold down the RESET BUTTON about 5 seconds. Releasing the reset button, the password will turn to the factory default.
Enable: Download unsigned ActiveX controls Enable: Initialize and script ActiveX controls not marked as safe Enable: Run ActiveX controls and plug-ins Figure 7.10 If you allow the ActiveX running, but still could not see living video. Please change another port number to try. Don’t use port 8000. Figure 7.11 Make sure that your firewall or anti-virus software does not block the camera or ActiveX. If you could not see video, please shut down firewall or anti-virus software to try again.
7.1.8 Can’t access IP camera in internet There are some reasons: 1. ActiveX controller is not installed correctly 2. The port which camera used is blocked by Firewall or Anti-virus software. Please change another port number and try again. (Figure 8.7) 3. Port forwarding is not successful (Figure 6.30) Check these settings and make sure they are correct. 7.1.9 UPnP always failed UPnP only contains port forwarding in our recent software.
Figure 7.13 Remove the plug-in from Chrome If you need to remove the plug-in from Google Chrome, please open a new tab. Click Customize and Control Google Chrome, then go to Tools Extensions. Find the IPCAM extension, and click the junk icon to remove it. Camera will prompt you to install the latest one when next logging. Figure 7.14 Remove the plug-in from Firefox If you need to remove the plug-in from Firefox, please open a new tab. Click the Firefox icon on the top right, then go to Add-ons.
Figure 7.15 7.2 Default Parameters Default network Parameters IP address: obtain dynamically Subnet mask: obtain dynamically Gateway: obtain dynamically DDNS: Embedded IPCAM DDNS Service Username and password Default admin username: admin with a blank password 7.3 Specification Item Image Sensor Lens Video Sensor High Definition Color CMOS Sensor Display Resolution 1.0 Megapixels Min. Illumination 0 Lux (With IR Illuminator) Lens Type Glass Lens focal length f:2.8mm Aperture F1.
Audio Network Input/Output Audio Compression External standard 3.5mm interface for twoway audio PCM/G.726 Ethernet One 10/100Mbps RJ45 port Wireless Standard IEEE802.11b/g/n Data Rate IEEE802.11b: 11Mbps(Max.); IEEE802.11g: 54Mbps(Max.); IEEE802.11n: 150Mbps(Max.).
7.4 CE & FCC Electromagnetic Compatibility (EMC) FCC Statement This device compiles with FCC Rules Part 15. Operation is subject to the following two conditions. This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
DECLARATION OF CONFORMITY Hereby, ebode electronics, declares that this ebode IPV58P2P is in compliance with the essential requirements and other relevant provisions of the following Directives: Directive 2004/108/EC of the European Parliament and of the Council of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonization of the laws of Member Sta
DECLARATION OF CONFORMITY TO R&TTE DIRECTIVE 1999/5/EC for the European Community, Switzerland, Norway, Iceland and Liechtenstein Product category: general consumer (category 3). English: This equipment is in compliance with the essential requirements and other relevant provisions of the European R&TTE Directive 1999/5/EC Deutsch [German]: Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden Vorgaben der Richtlinie 1999/5/EU.
Also available from ebode: Bluetooth Speaker and Bluetooth receiver .. Use the BT Sound to share the music on your smartphone, tablet or laptop wirelessly with your friends. As the BT Sound is small in size you can enjoy your favourite songs any place, anytime, anywhere! Ideal for parties, festivals or while travelling. Transmit the music from you smartphone, tablet or laptop wireless to your BT Sound Receiver. You easily hook this up to your amplifier, stereo set or your car audio system.
Also available from ebode: FM Transmitters and Infrared products .. Plug the FM Sound in your Smartphone and send the music wireless to your (car)radio. Works with any free frequency. Available for iPod, iPhone, iPad, Android, and any other device with a 3.5mm plug. The ebode line offers accessories for infrared control, such as single, dual or triple infrared emitters, either in a blinking or non-blinking version. Our optional emitter shields prevent unwanted, external IR signals from passing through.
www.ebodeelectronics.
