Users Manual
Table Of Contents
- FCC Statement
- 1.Overview
- 2.Technical parameter
- 3. Mechanical characteristics
- 4. Operation mode
- 5.Transmission mode
- 6.Application function and instruction configurati
- 6.1 Function pin
- 6.2 Wireless remote configuration function
- 6.3 Touch link Functional application
- 6.4 Functional parameter description
- 6.5 HEX User instruction set
- 6.6 HEX Parameter description
- 6.6.1 System transmitting mode
- 6.6.2 Receiving data output mode
- 6.6.3 Network node type
- 6.6.4 Network state
- 6.6.5 Network PAN_ID
- 6.6.6 Network short address：
- 6.6.7 MAC address
- 6.6.8 Short address of father nodes
- 6.6.9 MAC address of father nodes
- 6.6.10 Network group number group
- 6.6.11 Network Channel
- 6.6.12 Transmitting Power
- 6.6.13 Buad rate
- 6.6.14 Sleep time
- 6.6.15 Storage time of father nodes
- 6.6.16 Centralized network opening time
- 6.6.17 Period of network reconnection after loss o
- 6.6.18 The maximum number of attempts to reconnect
- 6.6.19 Wireless remote configuration ID
- 6.6.20 User gpio parameter
- 6.6.21 User pwm parameter
- 6.6.22 User adc parameter
- 6.6.23 Configure all network parameters
- 6.6.24 Configure all network parameters
- 6.6.25 Number of end-devices of the parent node
- 6.6.26 Parent node's end-device list
- 6.6.27 Configure the delayed printing time of AUX
- 6.6.29 Configure endpoint information
- 6.6.30 Set Link key of trust center
- 6.6.31 firmware version number
- 7.Quick start
- 8. Secondary development design reference
- 9.FAQ
- Revision history
- About us
Chengdu Ebyte Electronic Technology Co.,Ltd. E180-ZG120B User Manual
Copyright ©2012–2020, Chengdu Ebyte Electronic Technology Co.,Ltd.
27
node from 0 to child_count-1. Such as:
Receive：
FE 0E 33 FF
Retuen
：
FB 33 0 03 34 F3 0B 03 21 FE FF 57 B4 14
50ms
FB 33 1 04 F2 7B 02 1F 21 FE FF 57 B4 14
50ms
FB 33 2 04 A0 82 27 6E 21 FE FF 57 B4 14
50ms
FB 33 3 03 F4 3E F3 7C 21 FE FF 57 B4 14
50ms . . . .
. . . .
. . . .
FB 33 index dev_type Short_Addr Mac_Addr
6.6.27 Configure the delayed printing time of AUX wake up external MCU serial port in wireless
receiving state
AUX_delaytime: 1～255 unit is ms, the default parameter is 4ms, that is, after the module receives wireless data, first
pull down the AUX pin to wake up the external MCU, and then delay 4ms to output the serial port data to the external
MCU.
6.6.28 Configure serial port wake-up hold time
Uart_holdtime: The unit of 1～255 is 10ms, the default parameter is 100, that is, the serial port will keep waking up for
100*10ms after waking up, and then going to sleep after 1000ms.
6.6.29 Configure endpoint information
Endpoint_info：data format of 5 bytes are endpoint clusterId_H clusterId_L profileId_H profileId_L
Default is endpoint 0x01, clusterId 0xfeb0, profileId 0x0504
endpoint
clusterId
profileId
clusterId_H
clusterId_L
profileId_H
profileId_L
01
FE
B0
05
04
6.6.30 Set Link key of trust center
TrustCentLinkKey：data length of 16 bytes, default key of ZigBee alliance is
0x5A 0x69 0x67 0x42 0x65 0x65 0x41 0x6C
0x6C 0x69 0x61 0x6E 0x63 0x65 0x30 0x39