Use and Care Manual

ManualsBrandsEcho ManualsBrush Cutter99944200200

Sh o u l d e r ha r n e S S Kit

in S t a l l a t i o n in S t r u c t i o n S

P/N 99944200200

co n t e n t S :

1 - Harness ring 1 - Spacer

1 - Harness clamp 1 - Shoulder Harness

1 - 5 x 18 mm Bolt

Install Harness Clamp

Tools Required: Screwdriver, 8 x 10mm Open End Wrench.

Parts Required: Shoulder Harness Kit

1. Remove shield and gear housing as an assembly.

a. Loosen two (2) bolts (A) that clamp the gear housing to the

drive shaft.

b. Remove locating screw (B) found at the top of the gear

housing.

c. Pull shield and gear housing assembly (C) from the drive

shaft assembly.

IMPORTANT

Prevent exible drive cable from sliding from drive shaft housing.

If cable does slide free, clean dirt from cable and re-lubricate with

lithium based grease prior to re-assembly.

2. Remove front handle.

a. Remove screws, and handle bracket (D) from handle.

b. Remove front handle (E).

3. Install clamp.

a. Slightly spread clamp (F) and slide up shaft.

b. Install harness ring (G) using spacer (H) and 5x18mm bolt.

DO NOT tighten at this time.

Install Handle

1. Position handle (E) for comfortable operation, and tighten screws

securely.

99922200648

07/09

SUP22200648

Summary of content (8 pages)

PAGE 1
Shoulder Harness Kit Installation Instructions P/N 99944200200 Contents: 1 - Harness ring 1 - Harness clamp 1 - 5 x 18 mm Bolt 1 - Spacer 1 - Shoulder Harness Install Harness Clamp Tools Required: Screwdriver, 8 x 10mm Open End Wrench. Parts Required: Shoulder Harness Kit 1. Remove shield and gear housing as an assembly. a. b. c. Loosen two (2) bolts (A) that clamp the gear housing to the drive shaft. Remove locating screw (B) found at the top of the gear housing.
PAGE 2
Install Shield and Gear Housing Assembly C A 1. Install the gear housing and shield assembly. B 2. Align the gear housing on the drive shaft and install the locating screw (B). C 3. Tighten the two (2) side clamping screws (A). IMPORTANT Flat edge of washers (C) must be against drive shaft. Balance Unit 1. Put on harness and attach unit to harness. 2. Slide harness clamp up and down until unit balances with head approximately 2 - 3 in. from the ground. 3. Tighten clamp screw.
PAGE 3
Instrucciones de instalación arnés para el hombro Contenido: 1 - anillo de arnés 1 - abrazadera de arnés 1 - perno de 5x18mm 1 - espaciador 1 - arnés para el hombro N/P 99944200200 Instale la Abrazadera del Arnes Herramientas requeridas: Destornillador, llave de tuercas abierta de 8 mm x 10 mm. Piezas requeridas: Arnés para el kit del hombro 1. Retire juntas la pantalla y la cubierta de engranaje. a. Afloje los dos (2) pernos (A) que sujetan la cubierta de engranaje a la cubierta del eje motríz.
PAGE 4
Instale protector y caja del engranaje C 1. Instale la caja de engranajes y el conjunto de protector. A 2. Alinee la caja de engranajes en el eje de impulsión e instale el tornillo de localización (B). B 3. Apriete los dos (2) tornillos de sujeción laterales (A). C IMPORTANTE El lado plano de las arandelas (C) debe estar contra el eje del motor. Equilibre la unidad 1. Póngase el arnés y sujete la unidad al arnés. 2.
PAGE 5
Instructions d’installation kit de harnais d’épaule réf. 99944200200 Contenu : 1 - anneau de harnais 1 - collier de fixation de harnais 1 - boulon 5x18 mm 1 - entretoise 1 - harnais d’épaule Mise en Place de la Boucle de Harnais Outils nécessaires : tournevis, clé à molette de 8 mm x 10 mm Pièces nécessaires: kit de harnais d’épaule 1. Retirer le carter et la boîte d’engrenage ensemble. a. b. c. Desserrer les deux (2) boulons (A) rattachant la boîte d’engrenage à l’arbre moteur.
PAGE 6
Installation du pare débris et du carter d’engrenages C A 1. Installer l’ensemble carter d’engrenages et pare-débris. 2. Placer le carter d’engrenages sur l’arbre moteur et installer la vis de guidage (A). 3. Serrer les deux (2) vis latérales du collier (B). B C IMPORTANT Le côté plat des rondelles (D) doit être contre l’arbre d’entraînement. équilibrage de l’outil 1. Mettre le harnais sur l’épaule et y accrocher l’outil. 2.
PAGE 7
NOTES NOTAS REMARQUES
PAGE 8
ECHO CONSUMER PRODUCT SUPPORT: If you require assistance or have questions concerning the application, operation or maintenance of this product you may call the ECHO Consumer Product Support Department at 1-800-673-1558 from 8:30 am to 4:30 pm (Central Standard Time) Monday through Friday. Before calling, please know the model and serial number of your unit to help your Consumer Product Support Representative.