FOR MODELS: SRM-2100SB, 2400SB, 210SB, 211SB, 225SB, 260SB, 261SB, PAS-2100, 2400, 2601, 210, 211, 225, 225VP, 225VPB, 230, 231, 260, 261, 265, 266, 2620 (NOT FOR USE ON PAS-280) Operator’s Manual Users of this equipment risk injury to themselves and others if the unit is used improperly and/or safety precautions are not followed. ECHO provides an operator’s manual. It must be read and understood for proper and safe operation. Failure to do so could result in serious injury.
TABLE OF CONTENTS 99944200596 TABLE OF CONTENTS Introduction ................................................................................................. 3 Servicing Information .................................................................................. 3 Parts/Serial Number ............................................................................ 3 Service................................................................................................. 3 Echo Consumer Product Support ......
99944200596 INTRODUCTION INTRODUCTION The operators manual contains specifications and information for safety, operation, maintenance, storage and assembly specific to this product. Scan the QR codes throughout the operator’s manual for more information. The safety manual explains possible hazards and the measures you should take to insure safe operation. SERVICING INFORMATION Parts/Serial Number Genuine ECHO Parts and Assemblies for your ECHO products are available only from an Authorized ECHO Dealer.
SAFETY 99944200596 Echo Consumer Product Support If you require assistance or have questions concerning the application, operation, or maintenance of this product, call the ECHO Consumer Product Support Department at 1-800-673-1558 from 8:00 am to 5:00 pm (Central Standard Time) Monday through Friday. Before calling, please know the model and serial number of your unit. Product Registration Register your ECHO equipment on-line at www.echo-usa.
99944200596 SAFETY The safety alert symbol accompanied by the word “CAUTION” calls attention to an act or condition which may lead to minor or moderate personal injury if not avoided. The enclosed message provides information necessary for the protection of the unit. Note: This enclosed message provides tips for use, care and maintenance of the unit. CIRCLE AND SLASH SYMBOL This symbol means the specific action shown is prohibited. Ignoring these prohibitions can result in serious or fatal injury.
SAFETY 99944200596 Symbol Description Symbol Description Keep Feet Away From Blade Do not operate closer than 15 m (50 ft.) from electrical hazards. Keep bystanders at least 15 m (50 ft.) away. DO NOT USE BLADES - Line Head Only Thrown Objects Plan retreat path from falling objects. Hot Surface AVOID KICKOUT Keep Bystanders At Least 15 m (50 ft.) Away Beware Thrown Objects Wear Eye Protection Keep Bystanders and Helpers Away 15 m (50 ft.
99944200596 SAFETY Eye Protection ◆ Hand Protection Wear sturdy, no-slip, rubber work gloves to improve your grip on the handles. Gloves also provide protection against cuts and scratches, cold environments, and reduce the transmission of machine vibration to your hands. Hearing/Ear Protection ECHO recommends wearing hearing protection whenever unit is used.
SAFETY 99944200596 Heavy protective clothing can increase operator fatigue, which may lead to heat stroke. Schedule heavy work for early morning or late afternoon hours when temperatures are cooler. The components of this machine generate an electromagnetic field during operation, which may interfere with some pacemakers. To reduce the risk of serious or fatal injury, persons with pacemakers should consult with their physician and the pacemaker manufacturer before operating this machine.
9944200596 SAFETY Repetitive Stress Injuries (RSI) ENGLISH It is believed that overusing the muscles and tendons of the fingers, hands, arms, and shoulders may cause soreness, swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which could occur when your wrist swells and squeezes a vital nerve that runs through the area.
SAFETY 99944200596 Read the Manuals • Provide all users of this equipment with the Operator’s Manual and Safety Manual for instructions on Safe Operation. Clear the Work Area • Spectators and fellow workers must be warned, and children and animals prevented from coming nearer than 15 m (50 ft.) while the unit is in use. Keep a Firm Grip • Always hold throttle handle and support handle with thumbs and fingers tightly encircling the handles.
99944200596 SAFETY Avoid Hot Surfaces • Keep exhaust area clear of flammable debris. Avoid contact during and immediately after operation. ENGLISH Equipment Use this attachment with ECHO approved models only. Serious injury may result from the use of this attachment combined with a non approved ECHO product. • Check unit for loose/missing nuts, bolts, and screws. Tighten and/ or replace as needed. • Never adjust blades when the engine is operating. • Inspect hand guard for damage.
DESCRIPTION 99944200596 DESCRIPTION Locate the safety decal(s) on your unit. Make sure the decal(s) is legible and that you understand and follow the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. 1 7 6 3 2 5 4 15 m 50 ft 8 1. CUTTING BLADES 5. HAND GUARD / BLADE LOCK 2. LOWER DRIVE SHAFT ASSEMBLY 6. BLADE ADJUSTMENT HANDLE 3. FLEXIBLE DRIVE CABLE 7. BLADE COVER 4. SUPPORT HANDLE 8. SHOULDER HARNESS 12 X7712093000 © 04/2017 ECHO Inc.
99944200596 CONTENTS CONTENTS The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, some assembly may be necessary. 1 Articulating Hedge Clipper Attachment 1 Operator's Manual 1 Safety Manual 1 Blade Cover 1 Storage Hook Assembly ASSEMBLY Power Head Shaft To Lower Shaft Assembly Do not perform maintenance or assembly procedures with engine running. Parts Required: PAS or SRM-SB Power Head Shaft and Coupling 1. 2.
ASSEMBLY 5. Carefully fit attachment drive shaft assembly into coupler (B) to decal assembly line (C), making sure that the inner lower drive shaft engages the square upper drive shaft socket. 99944200596 B C Note: Earlier model power heads may have shorter couplings. Note: Lower bearing housing and head assembly must be in line with the engine. 6. 7. Rotate locater pin (A) ¼ turn clockwise to engage lower shaft hole. Insure locater pin is fully engaged by twisting lower drive shaft.
99944200596 OPERATION OPERATION Hedge Trimming Shoulder Harness (if included) Loosen the harness clamp screw. Put the harness on and attach it to the unit. Adjust the harness for comfortable operation. Tighten the harness clamp screw. Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause unconsciousness, serious injury, or death. Exhaust can cause serious burns. ALWAYS position unit so that exhaust is directed away from your face and body.
OPERATION 99944200596 Never remove hands from unit when blades are moving. The engine continues running even when the blades have stopped due to an obstruction. If this occurs, stop the engine, disconnect ignition cable and remove the obstruction. 1. 2. 3. Always grip throttle handle with right hand and support handle with left hand. Hold trimmer firmly and squeeze throttle trigger to accelerate engine. Tilt trimmer so cutting teeth are angled slightly toward the hedge or shrub and proceed to cut.
99944200596 OPERATION Always install the blade cover and place the cutter assembly in the folded / locked position for storage or transportation. Rotate Cutter Assembly Always use the unit from the right-hand side of your body – NEVER from the left side. Rotate cutter assembly 180 degrees on driveshaft in order to avoid cutting directly above your head, and to avoid contact with hot muffler. 1. 2. 3. Loosen gear case clamping screw (A) and remove gearcase locating screw (B).
MAINTENANCE 99944200596 MAINTENANCE Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and hot surfaces.
99944200596 MAINTENANCE Lubrication Blades ENGLISH Level 1. Parts Required: 20W Engine Oil (blade lubrication), 50-50 mixture of kerosene and 20W oil (blade cleaning) Hedge Clipper blades are very sharp. Touching them may lead to severe personal injury. Avoid touching blades whenever possible, and always wear gloves to protect hands. 1. 2. Brush loose debris from blade and coat both sides of blade with the 50-50 cleaning mixture.
MAINTENANCE Parts Required: 99944200596 Lithium Base Grease. Hedge Clipper blades are very sharp. Touching them may lead to severe personal injury. Avoid touching blades whenever possible, and always wear gloves to protect hands. 1. 2. Carefully remove locating screw (A) and loosen clamping screw (B). Remove the flex drive shaft assembly from the gear housing. Pull the drive shaft (C) from the drive shaft assembly, and wipe clean. Apply 15 ml (0.5 oz.) of grease. B A 3.
99944200596 MAINTENANCE Sharpening Level 2. ENGLISH If a power grinder is used DO NOT allow blade to over heat. 1. 2. Move stop switch to STOP position. Disconnect spark plug wire. 3. Remove blade guard, if installed (see “Blade Guard Remove/Install instructions”). 4. Slide blades to allow file clearance using slots (A) on bottom of blade. Do not pry against cutting edges. 5. File each edge carefully. Follow the original shape of the blade. 6.
STORAGE 99944200596 STORAGE Always store and transport hedge clippers in a stable position. Support gear case and cutting blades to prevent excessive flexing which may cause damage to the cutting attachment. Always install blade cover when transporting or storing unit. 1. 2. Clean and lubricate cutting blades and gear case. Sharpen cutting blades as required. 3. Apply a light coating of clean 20W engine oil along entire length of blades and on blade bolts. 4.
99944200596 SPECIFICATIONS SPECIFICATIONS MODEL Length Weight Gear Case Ratio Cutter Effective Length Pitch Maximum Diameter Cut Soft Material Woody Material X7712093000 © 04/2017 ECHO Inc. ENGLISH Width Height 99944200596 1100 mm (43.3 in.) storage position 1637 mm (64.4 in.) 0° position 150 mm (5.9 in.) 144 mm (5.7 in.) storage position 152 mm (6.0 in.) 0° position 2.55 kg (6.0 lb.) 4.6:1 Double Reciprocating Blade - Double Edge 557 mm (21.9 in.) 35 mm (1.38 in.) 25.4 mm (1 in.) 13 mm (0.5 in.
PRODUCT REGISTRATION 99944200596 PRODUCT REGISTRATION Thank you for choosing ECHO Power Equipment Please go to http://www.echo-usa.com/Warranty/Register-Your-ECHO to register your new product on-line. It's FAST and EASY! NOTE: your information will never be sold or misused by ECHO, Inc. Registering your purchase enables us to contact you in the unlikely event of a service update or product recall, and verifies your ownership for warranty consideration.
99944200596 PRODUCT REGISTRATION ENGLISH X7712093000 © 04/2017 ECHO Inc.
NOTES 99944200596 NOTES 26 X7712093000 © 04/2017 ECHO Inc.
99944200596 NOTES ENGLISH X7712093000 © 04/2017 ECHO Inc.
U02100001001 - U02100999999 ECHO, INCORPORATED 400 Oakwood Road Lake Zurich, IL 60047 www.echo-usa.
