Bed Redefiner Operator's Manual MODEL BRD-280 warning Users of this equipment risk injury to themselves and others if the unit is used improperly and/or safety precautions are not followed. ECHO provides an operator’s manual and a safety manual. Both must be read and understood for proper and safe operation. Failure to do so could result in serious injury.
Introduction Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-jobdependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will find both easy to use and full of helpful operations tips and SAFETY messages. the operator's manual Read and understand this manual before operation. Keep it in a safe place for future reference.
Bed Redefiner Operator's Manual Safety Manual Safety Symbols and Important Information Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages preceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to you. Circle and slash symbol DANGER This symbol means the specific action shown is prohibited. Ignoring these prohibitions can result in serious or fatal injury.
personal condition and safety equipment warning Users of this product risk injury to themselves and others if the unit is used improperly and/or safety precautions are not followed. Proper clothing and safety gear must be worn when operating unit. Physical Condition Your judgment and physical dexterity may not be good: • if you are tired or sick, • if you are taking medication, • if you have taken alcohol or drugs. Operate unit only if you are physically and mentally well.
Bed Redefiner Operator's Manual Repetitive Stress Injuries It is believed that overusing the muscles and tendons of the fingers, hands, arms, and shoulders may cause soreness, swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which could occur when your wrist swells and squeezes a vital nerve that runs through the area.
equipment warning Use only ECHO approved attachments. Serious injury may result from the use of a non approved attachment combination. ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which have not been tested and approved by ECHO. Read and comply with all safety instructions listed in this manual and safety manual. • • • • Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed.
Bed Redefiner Operator's Manual Description Locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the instructions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instructions for specific information.
1. POWER HEAD - Factory assembled. Includes the engine, clutch, fuel system, ignition system and starter. 2. THROTTLE TRIGGER LOCKOUT - This lever must be held during starting. Operation of the throttle trigger is prevented unless throttle trigger lockout lever is engaged. 3. STOP SWITCH - "Slide Switch" mounted on top of the throttle Trigger Housing. Move switch FORWARD to RUN, BACK to STOP. 4.
Bed Redefiner Operator's Manual Contents The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, some assembly may be necessary. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts.
5. Tighten two (2) drive shaft clamp bolts (B) securely. A B B throttle linkage and ignition leads 1. Close choke and remove air filter cover. 2. Place inner throttle cable in large hole of carburetor swivel (A). 3. Loosen nuts (B) and place threaded end of throttle linkage in bracket slot. Finger tighten nuts (B). 4. Check throttle for freedom of movement and that wide open throttle / low idle extremes are adjusted properly.
Bed Redefiner Operator's Manual 11 support handle Parts Required: Support Handle, Lower Bracket, 4 - 5 x 35 mm screws NOTE Label shows minimum spacing for front handle location. 1. Assemble front handle and bracket loosely to drive shaft. 2. Position front handle in comfortable operating position and tighten screws. MIN SPACING edger blade installation 1. Remove bed redefining blade as shown in “Blade Replacement” Section. Discard used split pin. 2.
Operation WARNING Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. WARNING Operation of this equipment may create sparks that can start fires around dry vegetation. This unit is equipped with a spark arrestor and a spark arrestor may be required.
Bed Redefiner Operator's Manual 13 Handling Fuel warning Fuel is VERY flammable. Use extreme care when mixing, storing or handling or serious personal injury may result. • Use an approved fuel container. • DO NOT smoke near fuel. • DO NOT allow flames or sparks near fuel. • Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize. • NEVER refuel a unit when the engine is HOT or RUNNING! • DO NOT fill fuel tanks indoors.
starting cold engine warning The attachment will operate immediately when the engine starts, and could result in possible serious injury. Keep movable parts of the attachment away from objects that could become entangled or thrown, and surfaces that could cause loss of control. 1. Stop Switch Move stop switch (A) away from the STOP position. 2. Choke Move choke (B) to “Cold Start” ( A ) Position. 3.
Bed Redefiner Operator's Manual starting warm engine The starting procedure is the same as Cold Start except DO NOT close the choke, and do not depress throttle trigger to wide open position. A warning The attachment should not move at idle, otherwise serious personal injury may result. NOTE If attachment moves, readjust carburetor according to “Carburetor Adjustment” instructions in this manual or see your ECHO Dealer. 1. Stop Switch Move stop switch (A) away from the STOP position 2.
operating techniques WARNING Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause unconsciousness, serious injury, or death. Exhaust can cause serious burns. ALWAYS position unit so that exhaust is directed away from your face and body. warning Before operating unit, be sure to read and understand the entire Operator’s Manual and Safety Manual to avoid the chance of serious personal injury.
Bed Redefiner Operator's Manual 8. If shield clogs with mud or debris, do not hit unit against hard surfaces to clean, or damage to unit may occur. Stop engine and unclog shield with a suitable tool. Important Be sure blade has completely stopped spinning before setting unit on concrete or other hard surface. Never allow spinning blade to contact hard surfaces. Carbide teeth on blade can break, or damage to surface can occur.
NOTE Blade depth may have to be adjusted due to differences in height between the hard surface and the top of the grass. 4. Loosen blade adjustment knob and adjust the blade’s depth of cut to produce a fine cut between sidewalk and grass using a minimum blade depth, usually with about 13 mm (1/2 in.) of the blade into the ground. Tighten adjustment knob. 5.
Bed Redefiner Operator's Manual 19 Maintenance WARNING Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and hot surfaces.
air filter Level 1. Parts required: 1. 2. 3. 4. REPOWERTM AIR & FUEL FILTER KIT. Close choke (cold start position). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumulated dirt from air cleaner area. Remove air filter cover and air filter retainer from inside cover. Brush dirt from inside cover. Replace filter if it is damaged, very dirty, or the rubber sealing edges are deformed.
Bed Redefiner Operator's Manual spark plug Level 2. Parts Required: REPOWERTM Tune-Up Kit IMPORTANT Use only NGK BPM-8Y spark plug (BPMR-8Y in Canada) otherwise severe engine damage may occur. 1. Remove spark plug and check for fouling, worn and rounded center electrode. 2. Clean the plug or replace with a new one. DO NOT sand blast to clean. Remaining sand will damage engine. 3. Adjust spark plug gap by bending outer electrode. 4. Tighten spark plug to 150-170 kgf • cm (130-150 in • lbf). 0.
IMPORTANT DO NOT use a metal scraper to remove dirt from the cylinder fins. 5. Use brush to remove dirt from the cylinder fins. 6. Remove grass and leaves from the grid between the recoil starter and fuel tank. 7. Assemble components in reverse order. exhaust system Spark Arrestor Screen Level 2. Parts Required: Spark Arrestor Screen, Gasket 1. Remove two (2) muffler cover screws and muffler cover (A). 2. Place piston at Top Dead Center (TDC) to prevent carbon/dirt from entering cylinder.
Bed Redefiner Operator's Manual Exhaust Port Cleaning Level 2. Parts Required: As needed: Heat Shield 1. Remove spark plug lead from spark plug, and remove muffler cover. 2. Place piston at top dead center. Remove muffler (A) and heat shield (B). 3. Use a wood or plastic scraping tool to clean deposits from cylinder exhaust port. IMPORTANT Never use a metal tool to scrape carbon from the exhaust port. Do not scratch the cylinder or piston when cleaning the exhaust port.
Level 2. Parts required: None NOTE Every unit is run at the factory and the carburetor is set in compliance with emission regulations. Carburetor adjustments, other than idle speed, must be performed by an authorized ECHO dealer. 1. Check idle speed and reset if necessary. If a tachometer is available, idle speed screw (A) should be set to the specifications found on "Specifications" page of this manual. Turn idle screw (A) clockwise to increase idle speed; counter clockwise to decrease idle speed.
Bed Redefiner Operator's Manual 25 blade replacement/lubrication Level 1. Parts Required: POWER BLENDXTM 8 oz. (P/N 91014) or Lithium Base Grease, Blade P/N 99944208000, split pin P/N 90030020022 NOTE Grease gear case every 15 - 25 hours of use. Replace blade when carbide tips have worn away. 1. Shut engine off. Disconnect spark plug lead from spark plug. 2. Remove split pin (A). 3. Rotate blade until holes in inner blade adapter (B) and gear box align.
8. Install inner blade adapter (B) onto PTO shaft (C). 9. Install and center new blade (F) onto inner fixing plate (B), with longest side toward shield. 10. Install outer fixing plate (E) and nut (D). Tighten nut (D) firmly, counterclockwise (CCW). IMPORTANT Never reuse old split pin. 11. Install new split pin (A) to secure nut.
Bed Redefiner Operator's Manual 27 Troubleshooting EnginE PrOBLEM TrOUBLESHOOTing CHarT Problem C h eck Fuel at carburetor Fuel at cylinder Engine cranks starts hard/ doesn't start Engine runs, but dies or does not accelerate properly Engine does not crank Status C au se No fuel at carburetor Fuel strainer clogged Fuel line clogged Carburetor remedy Clean or replace Clean or replace See your Echo dealer No fuel at cylinder C arburetor See your Echo dealer Muffler wet with fuel Fuel Mixture to
Storage warning During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may result. Long Term Storage (over 30 days) Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage maintenance which includes the following: 1.
Bed Redefiner Operator's Manual 29 Specifications MODEL ���������������������������������������������������� BRD-280 Length ������������������������������������������������������� 1791 mm (70.51 in.) Width �������������������������������������������������������� 280 mm (11.02 in.) Height ������������������������������������������������������� 300 mm (11.81 in.) Weight (dry w/cutter head) ������������������������������ 8.16 kg (18 lb.
Warranty Statements ECHO LIMITED WARRANTY STATEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO'S RESPONSIBILITY ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship.
Bed Redefiner Operator's Manual PURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES • 90-day residential, or non-income producing warranty • 30-day commercial, institutional, agricultural, industrial, income producing, or rental application warranty ATTENTION TWO-STROKE ENGINE POWER PRODUCT OWNERS This ECHO two-stroke engine power product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior performance.
ECHO INCORPORATED EMISSION CONTROL WARRANTY STATEMENT FOR ECHO AND SHINDAIWA BRANDS The Environmental Protection Agency (EPA) and the California Air Resources Board (C.A.R.B.) and ECHO Incorporated (ECHO Inc.) are pleased to explain the emission control system warranty on your 2010 and later equipment/small off-road engine (SORE). New equipment/SORE must be designed, built and equipped to meet stringent EPA and C.A.R.B. anti-smog standards. ECHO Inc.
Bed Redefiner Operator's Manual notes 33
notes
Bed Redefiner Operator's Manual notes 35
Servicing Information parts/serial number Genuine ECHO Parts and ECHO REPOWER™ Parts and Assemblies for your ECHO products are available only from an Authorized ECHO Dealer. When you do need to buy parts always have the Model Number, Type and Serial Number of the unit with you. You can find these numbers on the engine housing. For future reference, write them in the space provided below. Model No. ___________ Type _________SN.
