WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints, • Crystalline silica from bricks and cement and other masonry products, and • Arsenic and chromium from chemically treated lumber. Your risk from these exposures varies, depending on how often you do this type of work.
INTRODUCTION ECHO Engine Drill EDR-2100 TYPE1-E is a lightweight, high performance, two-stroke engined unit designed for drilling. WARNING DANGER IMPROPER USE OR CARE OF THIS UNIT, OR FAILURE TO WEAR PROPER PROTECTION CAN RESULT IN SERIOUS INJURY. READ AND UNDERSTAND THE RULES FOR SAFE OPERATION AND ALL INSTRUCTIONS IN THIS MANUAL. This Manual provides the information necessary for operation and maintenance.
SAFETY WARNING DANGER WARNING ENGINE DRILL USERS RISK INJURY TO THEMSELVES AND OTHERS IF THE ENGINE DRILL IS USED IMPROPERLY, AND/OR SAFETY PRECAUTIONS ARE NOT FOLLOWED. PROPER CLOTHING AND SAFETY GEAR MUST BE WORN WHEN OPERATING ENGINE DRILL. ALWAYS STOP THE ENGINE WHEN A DRILL JAM OCCURS. DO NOT ATTEMPT TO REMOVE AN OBJECT CAUSING A DRILL JAM IF THE ENGINE IS RUNNING. PHYSICAL INJURY CAN OCCUR IF A DRILL JAM IS REMOVED AND THE DRILLS START MOVING.
• Wear non-slip, heavy-duty work gloves to improve your grip on the engine drill handles. The gloves also help reduce the transmission of machine vibrations to your hands. PROTECTING OTHERS Spectators, children, fellow workers and animals must be warned to come no nearer than 4.6 m (15 feet) while the engine drill is in use. People working in the area near you should wear the same protective equipment as the operator.
Repetitive Stress Injuries It is believed that overusing the muscles and tendons of the fingers, hands, arms and shoulders may cause soreness, swelling, numbness, weakness and extreme pain in those areas. Certain repetitive hand activites may put you at a high risk for developing a Repetitives Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which could occur when your wrist swells and squeezes a vital nerve that runs through the area.
OPERATING TECHNIQUES • When starting to drill, run the engine at full throttle. WARNING DANGER BEFORE DRILLING, BE SURE TO READ AND UNDERSTAND THE ENTIRE OPERATOR’S MANUAL TO AVOID THE CHANCE OF SERIOUS INJURY. • Do not force the drills and only move as quickly as the drills will allow. • Stop the engine and disconnect from ignition cable before: - cleaning or when clearing a blockage; checking, maintenance or working on the machine. • Handle fuel with care; it is highly flammable.
DESCRIPTION 2 1 3 4 14 15 13 12 11 10 9 7 6 8 5 1 Operator’s manual - Included with unit. Read before operation and keep for future reference to learn proper, safe operating techniques. 11. Air cleaner cover - Covers air filter. 12. Starter handle - Pull handle to start the engine. 13. Throttle trigger lock out - Device that prevents the accidental operation of the throttle trigger until manually released. 2.
ASSEMBLING FRONT HANDLE • Incert the front handle to the machine, and turn clockwise. (TIGHTEN THE SCREW FIRMLY) Front handle DRILL BIT • Insert the drill bit (not provided with unit) until it reaches the bottom of the chuck, then back it out slightly; tighten the chuck laws evenly and completely. IMPORTANT Use drill bits suited for the material being drilled and for the depth of hole required.
IMPORTANT Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is added. Stored two-stroke fuel may separate. ALWAYS shake fuel container thoroughly before each use. STARTING COLD ENGINE • Stand the engine upright on a level surface. • Place ignition switch in ON (START/RUN) position. • Push purge bulb 3 to 4 times (or until fuel is visible in fuel return line). • Shift choke shutter to close position.
REVERSE ROTATION Clockwise (CW) • This model is equipped with reverse rotation mechanism. • When drilling, set shift lever down to clockwise (CW) rotation position. • If bit is locked due to deep penetration during drilling operation, set shift lever up to counterclockwise (CCW) rotation position and operate reversed for easy pulling-out. • When changing direction of drill rotation, operate as follows: Return engine to idle.
MAINTENANCE AND CARE AREA MAINTENANCE PAGE BEFORE USE Air Filter MONTHLY Clean/Replace 12 • Fuel Filter Inspect/Replace 12 • Spark Plug Inspect/Clean/ Adjust/Replace 12 • Carburettor Adjust 14 YEARLY DATE MAINTENANCE PERFORMED • • Cooling System Inspect/Clean 14 Silencer Inspect/Clean 14 • Starter Rope Inspect/Replace - • Drills Inspect/Clean/ Lubricate 13 Fuel Leaks Inspect/Repair - • Screw, Bolts & Nuts Inspect, Tighten/Replace - • Fuel Line Inspect - • • I
TROUBLE SHOOTING Trouble Engine - starts hard Cause Remedy • Fuel strainer clogged • Clean does not start Engine Fuel at No fuel Cranks carburettor at carburettor Fuel at No fuel at cylinder cylinder Silencer wet • Fuel line clogged • Clean • Carburettor • Ask your ECHO dealer • Carburettor • Ask your ECHO dealer • Fuel mixture is too rich • Open choke • Clean/replace air filter with fuel • Adjust carburettor • Ask your ECHO dealer Spark at No spark at • Ignition switch off • Tu
MAINTENANCE AIR FILTER • Air filter Clean before Use. - Remove air cleaner cover and pull out air fillter. - Lightly brush off dust or wash it in water and detergent. - Dry completely before putting it back in place. Air cleaner cover FUEL FILTER • Fuel filter Cap Check periodically. - Do not allow dust to enter into fuel tank. - Clogged filter will cause difficulty in starting engine or poor engine parformances. - Pick up fuel strainer through fuel inlet port with a piece of steel wire or the like.
REPLACEMENT OF CHUCK Replacement of chuck should be done in the following manner: 1. Remove bolt with hexagonal hole fixed in the driving axle. 2. Insert accessory hexagonal bar into chuck and fix. 3. Fit 19 mm spanner onto driving axle and keep it fitted. 4. Fit 10 mm box spanner onto the hexagonal bar and turn it into direction as indicated by an arrow to remove chuck. 5. Fit a new chuck in the reversed order of removing.
ADJUSTING CARBURETTOR (As Required) Low Speed Needle (L) GENERAL INFORMATION The idle speed adjuster screw controls the throttle opening at the idle position. IDLE ADJUSTMENT 1. Start engine and allow it to run at high idle until warm. Idle Speed Adjustment Screw 2. Turn the idle speed screw clockwise until drill begins to move. 3. Turn idle screw counter-clockwise 1 and 1/ 2 to 2 turn or until the drill stops (2,700 to 3,300 r/min).
STORAGE LONG TERM STORAGE (Over 30 Days) 6. Drain the fuel tank completely and pull the starter handle several times to remove fuel from the carburettor. Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage maintenance which includes the following: 7. Remove the spark plug and pour 1/2 tablespoon (1/4 oz) of fresh, clean, 2stroke engine oil into the cylinder through the spark plug hole. 1.
SPECIFICATIONS EDR-2100 TYPE1-E Masses Volume fuel tank Drill size (Max) chuck capacity speed Mission reduction ratio kg 4.6 (10.1 lb) L 0.5 (16.9 US fl oz) mm mm r/min 30 13 (0.5 inch) 430 17.1 (regular side) 18.6 (reverse side) grease lubrication External Dimensions length x width x height mm Engine type 420 x 328 x 255 (16.5 x 12.8 x 10.0 inch) Air cooled Two stroke single cylinder mL(cm³) 21.2 (1.
17
