X7722271404 / X772000164 PB-580 H/T Power Blower Operator’s Manual Burn Hazard The muffler or catalytic muffler and surrounding cover may become extremely hot. Always keep clear of exhaust and muffler area, otherwise serious personal injury may occur. The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
TABLE OF CONTENTS PB-580 H/T TABLE OF CONTENTS Table of contents ............................................................................................................................... 2 Introduction ........................................................................................................................................ 3 The Operator’s Manual ................................................................................................................ 3 Servicing information ....
PB-580 H/T INTRODUCTION INTRODUCTION Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job dependability. Read and understand this manual. You will find it easy to use and full of helpful operating tips and SAFETY messages. The Operator’s Manual Keep it in a safe place for future reference. Contains specifications and information for safety, operation, maintenance, storage and assembly specific to this product.
SAFETY PB-580 H/T SAFETY Manual Safety Symbols and Important Information Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages preceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to you. The safety alert symbol accompanied by the word “DANGER” calls attention to an act or condition which WILL lead to serious personal injury or death if not avoided.
PB-580 H/T SAFETY International Symbols Symbol Description Symbol Description Symbol Description Symbol Description Read and understand owners manual. Fuel and oil mixture Carburetor Adjustment Low speed mixture Carburetor Adjustment High speed mixture Wear eye, ear and head protection Finger severing Safety/Alert Carburetor Adjustment Idle speed Emergency Stop Hot Surface Idle Speed Fast speed Wear hand protection.
SAFETY PB-580 H/T Personal Condition and Safety Equipment Users of this product risk injury to themselves and others if the unit is used improperly and/or safety precautions are not followed. Proper clothing and safety gear must be worn when operating unit. Physical Condition Your judgment and physical dexterity may not be good: • If you are tired or sick. • If you are taking medication. • If you have taken alcohol or drugs. Operate unit only if you are physically and mentally well.
PB-580 H/T SAFETY • DO NOT OPERATE UNIT BAREFOOTED. Keep long hair away from engine and air intake. Retain hair with cap or net. Heavy protective clothing can increase operator fatigue, which may lead to heat stroke. Schedule heavy work for early morning or late afternoon hours when temperatures are cooler. The components of this machine generate an electromagnetic field during operation, which may interfere with some pacemakers.
SAFETY PB-580 H/T Repetitive Stress Injuries (RSI) It is believed that overusing the muscles and tendons of the fingers, hands, arms, and shoulders may cause soreness, swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which could occur when your wrist swells and squeezes a vital nerve that runs through the area.
PB-580 H/T SAFETY Keep a Solid Stance • Maintain footing and balance at all times. Do not stand on slippery, uneven or unstable surfaces. Do not work in odd positions or on ladders. Do not over reach. Avoid Hot Surfaces • Keep exhaust area clear of flammable debris. Avoid contact during and immediately after operation. Equipment Use only ECHO attachments. Serious injury may result from the use of a non-approved attachment combination. ECHO, INC.
EMISSION CONTROL (EXHAUST & EVAPORATIVE) PB-580 H/T EMISSION CONTROL (EXHAUST & EVAPORATIVE) EPA 2010 and Later and/or C.A.R.B. TIER III The emission control system for the engine is EM (engine modification) and, if the second to last character of the Engine Family on the Emission Control Information label (sample below) is “C”, “K”, or “T”, the emission control system is EM and TWC (3-way catalyst). The fuel tank/fuel line emission control system is EVAP (evaporative emissions).
PB-580 H/T DESCRIPTION DESCRIPTION PB-580H Locate the safety decal(s) on your unit. Make sure the decal(s) is legible and that you understand and follow the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instructions for specific information. 8 8 7 10 2 12 9 11 1 4 13 5 14 4 6 3 Hot Decal Sound Label X7505200601 © 04/2015 ECHO Inc.
DESCRIPTION PB-580 H/T 1. SAFETY DECAL - Lists important safety precautions. 2. SPARK PLUG - Provides spark to ignite fuel mixture. 3. SPARK ARRESTOR - CATALYTIC MUFFLER / MUFFLER - The muffler or catalytic muffler controls exhaust noise and emission. The spark arrestor screen prevents hot, glowing particles of carbon from leaving the muffler. Keep exhaust area clear of flammable debris. 4. RECOIL STARTER HANDLE - Pull recoil handle slowly until recoil starter engages, then quickly and firmly.
PB-580 H/T DESCRIPTION PB-580T Locate the safety decal(s) on your unit. Make sure the decal(s) is legible and that you understand and follow the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instructions for specific information. 7 8 7 10 2 9 1 5 13 3 4 14 6 12 11 13 3 12 Hot Decal Sound Label X7505200601 © 04/2015 ECHO Inc.
DESCRIPTION PB-580 H/T 1. SAFETY DECAL - Lists important safety precautions. 2. SPARK PLUG - Provides spark to ignite fuel mixture. 3. SPARK ARRESTOR - CATALYTIC MUFFLER / MUFFLER - The muffler or catalytic muffler controls exhaust noise and emission. The spark arrestor screen prevents hot, glowing particles of carbon from leaving the muffler. Keep exhaust area clear of flammable debris. 4. RECOIL STARTER HANDLE - Pull recoil handle slowly until recoil starter engages, then quickly and firmly.
PB-580 H/T CONTENTS CONTENTS After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts.
ASSEMBLY PB-580 H/T ASSEMBLY PB-580 H Never perform maintenance or assembly procedures with engine running or serious personal injury may result. A B A Install Blower Pipes/Stick Handle 1. Assemble clamps (A) onto both ends of flexible pipe (B). 2. Assemble straight pipe with swivel (C) into flexible pipe (B). 3. Assemble flexible pipe (B) to elbow (D) on blower and tighten clamps (A). Note: A light lubricant may be used to ease assembly of flexible pipe to blower elbow. D A C B A 4.
PB-580 H/T ASSEMBLY Note: Blower use will eventually loosen pipe connections. Exclusive positive locking system allows pipes to be tightened. If loosening occurs, remove two straight pipes and install according to instructions 7 & 8. For more information scan this QR code. PB-580T Never perform maintenance or assembly procedures with engine running or serious personal injury may result. Install Blower Pipes 1. Assemble clamps (A) onto both ends of flexible pipe (B).
OPERATION PB-580 H/T 6. Move handle (E) to desired position. Tighten knob (H) hand tight. E H 7. Assemble straight pipe (I) onto swivel pipe (C), until you feel light resistance. Do not force connection. Hold swivel pipe and turn straight pipe clockwise, engaging positive locking channels, until connection is firm. Do not force connection. 8. Assemble straight pipe with decal (J) to straight pipe (I) as in step 8. C Note: Blower use will eventually loosen pipe connections.
PB-580 H/T OPERATION Fuel Alternative fuels, such as E-15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting ECHO requirements are NOT approved for use in ECHO 2-stroke gasoline engines. Use of alternative fuels may cause performance problems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited to, improper clutch engagement.
OPERATION PB-580 H/T Mixing Instructions 1. Fill an approved fuel container with half of the required amount of gasoline. 2. Add the proper amount of 2-stroke oil to gasoline. 3. Close container and shake to mix oil with gasoline. 4. Add remaining gasoline, close fuel container, and remix. Spilled fuel is a leading cause of hydrocarbon emissions. Some states may require the use of automatic fuel shut-off containers to reduce fuel spillage. For more information scan this QR code.
PB-580 H/T OPERATION 5. Choke B After engine fires (or 5 pulls), move choke lever back to RUN ( ) position, then pull starter handle/rope until engine starts and runs. Allow unit to warm up at idle for several minutes. Note: If engine does not start with choke in “RUN” position after 5 pulls, move choke to COLD START ( ) position, and repeat steps 3- 5. C D 6. Throttle Lever Allow engine to warm up for several minutes before use. 7.
OPERATION PB-580 H/T 2. Throttle Lever Move Throttle Lever (A) all the way forward to STOP position. If engine does not stop when stop switch is moved to STOP position, close choke - COLD START position - to stall engine. Have your ECHO dealer repair stop switch before using unit again. Operating Blower Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause unconsciousness, serious injury, or death. Exhaust can cause serious burns.
PB-580 H/T OPERATION 6. Additional speed may be necessary to clean grass and leaves from a lawn or flower bed. For more information scan this QR code. 7. Higher speed may be necessary to move gravel, dirt, snow, bottles or cans from a driveway, street, parking lot or stadium. 8. Always stop unit using stop engine procedure. Note: Never use a higher speed setting than necessary to perform a task. Remember, the higher the engine speed, the louder the blower noise. 9.
OPERATION PB-580 H/T Intake Cover (optional) In cold weather, intake cover can be installed for operator comfort. Intake cover is not included. 1. Remove back cushion (A) from frame. 2. Install intake cover (B) on frame over air intake. A 3. Install back cushion (A) to frame over intake cover. Note: Blower performance may be reduced slightly. B Adjust the Harness 1. Loosen upper and lower buckles (A), then put blower on your back. 2. Pull strap (B) downward to adjust position of blower. 3.
PB-580 H/T MAINTENANCE MAINTENANCE Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and hot surfaces. Your ECHO unit is designed to provide many hours of trouble free service.
MAINTENANCE PB-580 H/T Air Filter Level 1. Parts Required: REPOWERTM Tune Up Kit. 1. CLOSE choke (COLD START [ ] position). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumulated dirt from air cleaner area. 2. Remove air filter cover. Brush dirt from inside cover. 3. Remove air filter and lightly brush debris from filter. Replace filter if it is damaged, fuel soaked, very dirty, or the rubber sealing edges are deformed. 4.
PB-580 H/T MAINTENANCE Spark Plug Level 2. Parts Required: REPOWERTM Tune-Up Kit Use only NGK BPM-8Y spark plug (BPMR-8Y in Canada) otherwise severe engine damage may occur. 0.65 mm (0.026 in.) 1. Remove spark plug and check for fouling, worn and rounded center electrode. 2. Clean the plug or replace with a new one. DO NOT sand blast to clean. Remaining sand will damage engine. 3. Adjust spark plug gap by bending outer electrode. 4. Tighten spark plug to 150-170 kgf • cm (130-150 in • lbf).
MAINTENANCE PB-580 H/T Cleaning Cylinder Fins 1. Remove spark plug. 2. Remove starter 3. Remove engine cover. 4. Clean cylinder fins (A) to allow cooling air to pass freely 5. Assemble components in reverse order. A Exhaust System Spark Arrestor Screen Level 2. Parts Required: Spark Arrestor Screen, Gasket Carbon deposits in muffler will cause a drop in engine output and overheating. Spark arrestor screen must be checked periodically. 1. Remove spark plug. 2. Remove starter C B A 3.
PB-580 H/T MAINTENANCE Exhaust Port Cleaning Level 2. Parts Required: B A Heat shield 1. Remove spark plug. 2. Remove starter 3. Remove engine cover. 4. Place piston at top dead center. Remove muffler (A) heat shield (B). 5. Use a wood or plastic scraping tool to clean deposits from cylinder exhaust port. Never use a metal tool to scrape carbon from the exhaust port. Do not scratch the cylinder or piston when cleaning the exhaust port. Do not allow carbon particles to enter the cylinder. 6.
MAINTENANCE PB-580 H/T Carburetor Adjustment Engine Break-In New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be made. During the break-in period your engine performance will increase and exhaust emissions will stabilize. Idle speed can be adjusted as required. High Altitude Operation This engine has been factory adjusted to maintain satisfactory starting, emission, and durability performance up to 1,100 feet above sea level (ASL) (96.0 kPa).
PB-580 H/T MAINTENANCE Throttle Cable Adjustment Level 1 If engine idle speed changes when blower pipe is moved, or engine will not reach full wide open throttle speed, adjust throttle cable. 1. Loosen handle adjustment knob (C) and tilt Tube Throttle handle forward to expose Adjustment Screw (D). C D 2. Turn Adjustment Screw until Throttle Trigger free play is 4 - 6 mm (3/16-1/4 in.). 3.
TROUBLESHOOTING PB-580 H/T TROUBLESHOOTING ENGINE PROBLEM TROUBLESHOOTING CHART Problem Check Clean or replace Clean or replace See your Echo dealer No fuel at cylinder Carburetor See your Echo dealer Muffler wet with fuel Fuel Mixture too rich Open choke Clean/replace air filter See your Echo dealer No spark Stop switch OFF Electrical problem Interlock switch Turn switch to ON See your Echo dealer See your Echo dealer Spark at plug No spark Spark gap incorrect Covered with carbon Fouled wit
PB-580 H/T STORAGE STORAGE During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may result. Long Term Storage (Over 30 Days) Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage maintenance which includes the following: 1.
SPECIFICATIONS PB-580 H/T SPECIFICATIONS MODEL PB-580 H PB-580 T Length (w/o pipes) 379 mm (14.92in.) 379 mm (14.92 in.) Width (w/o pipes) 537 mm (21.14 in.) 478 mm (18.82 in.) Height (w/o pipes) Weight (dry) (w/o pipes) Engine Type 459 mm (18.07 in.) 9.4 kg (20.7 lb.) 9.3 kg (20.5 lb.) Air cooled, two-stroke, single cylinder gasoline engine Bore 46.0 mm (1.81 in.) Stroke 35.0 mm (1.38 in.
PB-580 H/T WARRANTY STATEMENTS WARRANTY STATEMENTS ECHO LIMITED WARRANTY STATEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO'S RESPONSIBILITY ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship.
WARRANTY STATEMENTS PB-580 H/T ECHO does not offer an over the counter exchange program. Any ECHO product re-built other than by ECHO or sold through an unauthorized dealer, or an unauthorized outlet store, is sold without ECHO’s limited warranty coverage. The ECHO Limited Warranty coverage is extended to the original purchaser only, and is not transferable except for emission related parts.
PB-580 H/T PRODUCT REGISTRATION PRODUCT REGISTRATION Thank you for choosing ECHO Power Equipment Please go to http://www.echo-usa.com/Warranty/Register-Your-ECHO to register your new product on-line. It's FAST and EASY! NOTE: your information will never be sold or misused by ECHO, Inc. Registering your purchase enables us to contact you in the unlikely event of a service update or product recall, and verifies your ownership for warranty consideration.
NOTES PB-580 H/T NOTES 38 X7505200601 © 04/2015 ECHO Inc.
PB-580 H/T X7505200601 © 04/2015 ECHO Inc.
(H): P44514001001 - P44514999999 (T): P44614001001 - P44614080844 40
