x7722271404 / x772000164 PE-225 POWER EDGER Operator’s Manual Burn Hazard The muffler or catalytic muffler and surrounding cover may become extremely hot. Always keep clear of exhaust and muffler area, otherwise serious personal injury may occur. The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
TABLE OF CONTENTS PE-225 TABLE OF CONTENTS Table of Contents .............................................................................................................................. 2 Introduction ........................................................................................................................................ 3 The Operator’s Manual ................................................................................................................ 3 The Safety Manual..............
PE-225 INTRODUCTION INTRODUCTION Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job dependability. Read and understand this manual and the SAFETY MANUAL. You will find both easy to use and full of helpful operating tips and SAFETY messages. The Operator’s Manual Keep it in a safe place for future reference. Contains specifications and information for safety, operation, maintenance, storage and assembly specific to this product.
SAFETY PE-225 Additional or Replacement Manuals Replacement Operator, Safety Manuals, and Parts Catalogs are available from your ECHO dealer or at www.echo-usa.com or by contacting ECHO Inc., 400 Oakwood Road, Lake Zurich, IL 60047 (800-673-1558). Always check the ECHO Web Site for updated information. Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video.
PE-225 SAFETY International Symbols Symbol Description Symbol Description Symbol Description Symbol Description Warning, See Operator’s Manual Carburetor Adjustment High speed mixture DO NOT allow flames or sparks near fuel Ignition ON / OFF Wear eye, ear and head protection Carburetor Adjustment Idle speed DO NOT smoke near fuel Primer Bulb Wear hand and foot protection Carburetor Adjustment Low speed mixture Choke Control “Run” Position (Choke Open) Choke Control “Cold Start” Position
SAFETY PE-225 Hand Protection Wear no-slip, heavy duty work gloves to improve your grip on the handles. Gloves also reduce the transmission of machine vibration to your hands. Breathing Protection Wear a facemask to protect against dust. Hearing Protection ECHO recommends wearing hearing protection whenever unit is used. Proper Clothing Wear snug fitting, durable clothing; • Pants should have long legs, shirts with long sleeves.
PE-225 SAFETY • Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks, and also by not smoking. • Limit the hours of operation. Try to fill each day with jobs where operating the unit or other hand-held power equipment is not required. • If you experience discomfort, redness, and swelling of the fingers followed by whitening and loss of feeling, consult your physician before further exposing yourself to cold and vibration.
SAFETY PE-225 Read the Manuals • Provide all users of this equipment with the Operator’s Manual and Safety Manual for instructions on Safe Operation. Clear the Work Area • Spectators and fellow workers must be warned, and children and animals prevented from coming nearer than 15 m (50 ft.) while the unit is in use. Keep a Firm Grip • Hold both handles with thumbs and fingers encircling the grips. Keep a Solid Stance • Maintain footing and balance at all times.
PE-225 EMISSION CONTROL (EXHAUST & EVAPORATIVE) Check fuel system for leaks due to fuel tank damage, especially if the unit is dropped. If damage or leaks are found, do not use unit, otherwise serious personal injury or property damage may occur. Have unit repaired by an authorized servicing dealer before using. EMISSION CONTROL (EXHAUST & EVAPORATIVE) EPA 2010 and Later and/or C.A.R.B.
DESCRIPTION PE-225 DESCRIPTION Locate the safety decal(s) on your unit. Make sure the decal(s) is legible and that you understand and follow the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instructions for specific information. 19 11 12 13 18 14 17 15 16 6 5 4 3 7 2 1 8 9 10 Shaft Label 10 Hot Label Handle Label X7722272307 © 3/2013 ECHO Inc.
PE-225 DESCRIPTION 1. POWER HEAD - Includes the Engine, Clutch, Fuel System, Ignition System and Recoil Starter. 2. THROTTLE TRIGGER LOCKOUT - This lever must be held during starting. Operation of the throttle trigger is prevented unless throttle trigger lockout lever is engaged. 3. STOP SWITCH - “SLIDE SWITCH” mounted on top of the Throttle Trigger Housing. Move switch FORWARD to RUN, BACK to STOP. 4.
CONTENTS PE-225 CONTENTS The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, shield installation and other assembly may be necessary. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts.
PE-225 ASSEMBLY ASSEMBLY Drive Shaft/Power Head Parts Required: Power Head, Drive Shaft Assembly 1. Stand engine on a level surface. 2. Remove vinyl cap from drive shaft. 3. Loosen the two bolts (A) at drive shaft end of engine. 4. Carefully fit drive shaft assembly to engine, making sure that inner drive shaft engages into clutch mount. Note: Rotate the drive shaft housing until edger housing is in line with the engine. 5. Tighten bolts (A). Throttle Linkage and Ignition Leads D 1.
ASSEMBLY 5. Secure ignition leads against engine housing with clips (H, I). PE-225 I 6. Install air filter and cover. Front Handle 1. Position front handle in comfortable operating position and tighten screws. Note: Label shows minimum spacing for front handle location. 14 MI N SP AC ING X7722272307 © 3/2013 ECHO Inc.
PE-225 OPERATION OPERATION Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Operation of this equipment may create sparks that can start fires. This unit is equipped with a spark arrestor to prevent discharge of hot particles from the engine.
OPERATION PE-225 • Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize. • NEVER refuel a unit when the engine is HOT or RUNNING! • DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground. • DO NOT overfill fuel tank. Wipe up spills immediately. • Securely tighten fuel tank cap and close fuel container after refueling. • Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired.
PE-225 OPERATION Starting Cold Engine A The attachment will operate immediately when the engine starts, and could result in possible serious injury. Keep movable parts of the attachment away from objects that could become entangled or thrown, and surfaces that could cause loss of control. 1. Stop Switch Move stop switch button (A) forward, away from the STOP position. 2. Choke Move choke lever (B) to Cold Start Position ( ). 3.
OPERATION PE-225 Note: If attachment moves, readjust carburetor according to “Carburetor Adjustment” instructions in this manual or see your ECHO Dealer. 1. Stop Switch Move stop switch button (A) forward away from the STOP position. 2. Purge Bulb Pump purge bulb (C) until fuel is visible in the “Clear” fuel return line. C 3. Recoil Starter Lay the unit on a flat area and keep movable attachment parts clear of all obstacles. Rapidly pull the recoil starter handle (D) until the engine fires.
PE-225 OPERATION 1. Before edging, water the area to soften the ground to make edging easier. 2. Before edging, check the area and remove all obstacles and objects that could be thrown. 3. Plan to edge regularly to make it easier to keep a neat edge and to avoid having to make more than one pass. Note: Blade depth may have to be adjusted due to differences in height between the hard surface and the top of the grass.
MAINTENANCE PE-225 MAINTENANCE Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and hot surfaces. Your ECHO unit is designed to provide many hours of trouble free service.
PE-225 MAINTENANCE * Replacement is recommended based on the finding of damage or wear during inspection. Air Filter Level 1. Parts Required: REPOWERTM AIR & FUEL FILTER KIT. 1. Close choke (Cold Start Position [ ]). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumulated dirt from air cleaner area. 2. Remove air filter cover. Brush dirt from inside cover. 3. Remove air filter and lightly brush debris from filter.
MAINTENANCE PE-225 Spark Plug Level 2. Parts Required: REPOWERTM Tune-Up Kit Use only NGK BPM-8Y spark plug (BPMR-8Y in Canada) otherwise severe engine damage may occur. .65 mm (.026 in.) 1. Remove spark plug and check for fouling, worn and rounded center electrode. 2. Clean the plug or replace with a new one. DO NOT sand blast to clean. Remaining sand will damage engine. 3. Adjust spark plug gap by bending outer electrode. 4. Tighten spark plug to 150-170 kgf • cm (130-150 in • lbf).
PE-225 MAINTENANCE 2. Remove air cleaner cover (A). 3. Remove engine cover (B). B A DO NOT use a metal scraper to remove dirt from the cylinder fins. 4. Use brush to remove dirt from the cylinder fins. 5. Remove ignition wires from clip for cleaning. 6. Remove grass and leaves from the grid between the recoil starter and fuel tank. 7. Assemble components in reverse order. Exhaust System Spark Arrestor Screen Level 2. Parts Required: F Spark Arrestor Screen, Gasket 1. Remove engine cover (B). 2.
MAINTENANCE Exhaust Port Cleaning Level 2. Parts Required: PE-225 B A As needed: Heat Shield 1. Remove spark plug lead from spark plug, and remove engine cover. 2. Place piston at top dead center. Remove muffler (A) and heat shield (B). 3. Use a wood or plastic scraping tool to clean deposits from cylinder exhaust port. Never use a metal tool to scrape carbon from the exhaust port. Do not scratch the cylinder or piston when cleaning the exhaust port. Do not allow carbon particles to enter the cylinder.
PE-225 MAINTENANCE Note: Every unit is run at the factory and the carburetor is set in compliance with emission regulations. Carburetor adjustments, other than idle speed, must be performed by an authorized ECHO dealer. 1. Check idle speed and reset if necessary. If a tachometer is available, idle speed screw (A) should be set to the specifications found on “Specifications” page of this manual. Turn idle screw (A) clockwise to increase idle speed; counter clockwise to decrease idle speed.
MAINTENANCE PE-225 Blade Replacement Level 1. Parts Required: Blade, new split pin Note: Replace blade when it is bent, damaged, or worn shorter than 6 inches. 1. Remove split pin (A). 2. Align hole in inner blade adapter (B) with notch in gear housing, and insert locking tool (G) to prevent PTO shaft (C) from rotating. 3. Remove L.H. blade nut (D) by turning clockwise. Remove outer blade adapter (E), and blade (F). G B C F 4. Install and center blade (F) on inner blade adapter (B). 5.
PE-225 TROUBLESHOOTING TROUBLESHOOTING ENGINE PROBLEM TROUBLESHOOTING CHART Problem Check Engine does not crank Remedy Fuel strainer clogged Fuel line clogged Carburetor Clean or replace Clean or replace See your Echo dealer No fuel at cylinder Carburetor See your Echo dealer Muffler wet with fuel Fuel Mixture too rich Open choke Clean/replace air filter Adjust carburetor See your Echo dealer No spark Stop switch off Electrical problem Interlock switch Turn switch to ON See your Echo dealer
STORAGE PE-225 STORAGE During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may result. Long Term Storage (Over 30 Days) Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage maintenance which includes the following: 1.
PE-225 SPECIFICATIONS SPECIFICATIONS MODEL PE-225 Length 1772 mm (68.6 in.) Width 305 mm (12.0 in.) Height 370 mm (14.6 in.) Weight (dry) w/Cutter Head 6.0 kg (13.2 lb.) Engine Type Air cooled, two-stroke, single cylinder gasoline engine Bore 32.2 mm (1.27 in.) Stroke 26.0 mm (1.02 in.) Displacement 21.2 cc (1.29 cu. in.
WARRANTY STATEMENTS PE-225 WARRANTY STATEMENTS ECHO LIMITED WARRANTY STATEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO'S RESPONSIBILITY ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship.
PE-225 WARRANTY STATEMENTS PURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES & GJ* * & ^J* ATTENTION TWO-STROKE ENGINE POWER PRODUCT OWNERS This ECHO two-stroke engine power product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior performance.
NOTES PE-225 NOTES 32 X7722272307 © 3/2013 ECHO Inc.
PE-225 X7722272307 © 3/2013 ECHO Inc.
NOTES 34 PE-225 X7722272307 © 3/2013 ECHO Inc.
PE-225 X7722272307 © 3/2013 ECHO Inc.
ECHO, INCORPORATED 36 400 Oakwood Road Lake Zurich, IL 60047 www.echo-usa.
