Power Edger Operator's Manual MODEL PE-265 PE-265S warning Read rules for safe operation and instructions carefully. ECHO provides an Operator's Manual and a Safety Manual. Both must be read and understood for proper and safe operation.
Introduction Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-jobdependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will find both easy to use and full of helpful operations tips and SAFETY messages. the operator's manual Read and understand this manual before operation. Keep it in a safe place for future reference.
Power Edger Operator's Manual Safety Manual Safety Symbols and Important Information Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages preceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to Circle and slash symbol DANGER This symbol means the specific action shown is prohibited. Ignoring these prohibitions can result in serious or fatal injury.
personal condition and safety equipment warning Edger users risk injury to themselves and others if the edger is used improperly and or safety precautions are not followed. Proper clothing and safety gear must be worn when operating an edger. Physical Condition Your judgment and physical dexterity may not be good: • if you are tired or sick, • if you are taking medication, • if you have taken alcohol or drugs. Operate unit only if you are physically and mentally well.
Power Edger Operator's Manual Repetitive Stress Injuries It is believed that overusing the muscles and tendons of the fingers, hands, arms, and shoulders may cause soreness, swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which could occur when your wrist swells and squeezes a vital nerve that runs through the area.
equipment warning Use only ECHO approved attachments. Serious injury may result from the use of a non approved attachment combination. ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which have not been tested and approved by ECHO. Read and comply with all safety instructions listed in this manual and safety manual. • • • • Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed.
Power Edger Operator's Manual Description Locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the instructions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instructions for specific information.
5 6 PE-265S 4 3 2 7 1 8 9 10 Shaft Decal P/N X505002510 P/N X505001930
Power Edger Operator's Manual 1. POWER HEAD - Factory assembled. Includes the engine, clutch, fuel system, ignition system and starter. 2. THROTTLE TRIGGER LOCKOUT - This lever must be held during starting. Operation of the throttle trigger is prevented unless throttle trigger lockout lever is engaged. 3. STOP SWITCH - "Slide Switch" mounted on top of the throttle Trigger Housing. Move switch FORWARD to RUN, BACK to STOP. 4.
Contents The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, some assembly may be necessary. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts.
Power Edger Operator's Manual 5. Tighten two (2) drive shaft clamp bolts (B) securely. 6. Route throttle linkage and ignition lead assembly along shaft and clip as shown. 11 A B B throttle linkage and ignition leads 1. Close choke and remove air filter cover. 2. Place throttle linkage (C) through adjustment fixture (D) and install wire end into large carburetor throttle swivel hole (E). Check throttle for freedom of movement and that wide open throttle / low idle extremes are adjusted properly.
front handle Tools Required: Torx T27 L-Wrench Parts Required: Front Handle, Lower Bracket, 4 - 5 x 35 mm screws NOTE Label shows minimum spacing for front handle location. 1. Assemble front handle and bracket loosely to drive shaft. 2. Position front handle in comfortable operating position and tighten screws. MIN SPACING Operation WARNING Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings.
Power Edger Operator's Manual 13 Fuel Requirements Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up to 10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood alcohol) is NOT approved. Two Stroke Oil - A two-stroke engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FC/FD Standards must be used. Echo brand premium Power Blend X TM Universal 2-Stroke Oil meets these standards.
starting cold engine warning The attachment will operate immediately when the engine starts and could result in loss of control and possible serious injury. Keep movable parts of the attachment off the ground and away from objects that could become entangled or thrown. 1. Stop Switch Move stop switch (A) away from the STOP position. 2. Choke Move choke (B) to “Cold Start” ( A ) Position. B 3.
Power Edger Operator's Manual starting warm engine The starting procedure is the same as Cold Start except DO NOT close the choke, and do not depress throttle trigger to wide open position. A warning The attachment should not move at idle, otherwise serious personal injury may result. NOTE If attachment moves, readjust carburetor according to “Carburetor Adjustment” instructions in this manual or see your ECHO Dealer. 1. Stop Switch Move stop switch (A) away from the STOP position 2.
operating techniques WARNING Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause unconsciousness, serious injury, or death. Exhaust can cause serious burns. ALWAYS position unit so that exhaust is directed away from your face and body. 1. 2 3. Before edging, water the area to soften the ground to make edging easier. Before edging, check the area and remove all obstacles and objects that could be thrown.
Power Edger Operator's Manual 17 Maintenance WARNING Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and hot surfaces.
air filter Level 1. Tools required: 25 or 50 mm (1 or 2 in.) Cleaning brush Parts required: REPOWERTM AIR & FUEL FILTER KIT. 1. ]). This prevents dirt from Close choke (Cold Start Position [ entering the carburetor throat when the air filter is removed. Brush accumulated dirt from air cleaner area. 2. Remove air filter cover. Brush dirt from inside cover. 3. Remove air filter and lightly brush debris from filter.
Power Edger Operator's Manual 19 spark plug Level 2. Tools Required: T-Wrench, feeler gauge, soft metal brush Parts Required: REPOWERTM Tune-Up Kit IMPORTANT Use only NGK BPM-8Y spark plug (BPMR-8Y in Canada) otherwise severe engine damage may occur. 1. Remove spark plug and check for fouling, worn and rounded center electrode. 2. Clean the plug or replace with a new one. DO NOT sand blast to clean. Remaining sand will damage engine. 3. Adjust spark plug gap by bending outer electrode. 4.
IMPORTANT DO NOT use a metal scraper to remove dirt from the cylinder fins. 5. Use brush to remove dirt from the cylinder fins. 6. Remove grass and leaves from the grid between the recoil starter and fuel tank. 7. Assemble components in reverse order. exhaust system Spark Arrestor Screen Level 2. Tools Required: Cross Head Screwdriver, 4mm Hex Wrench, Soft Metal Brush Parts Required: Spark Arrestor Screen, Gasket 1. Remove muffler cover screw and muffler cover (A). 2.
Power Edger Operator's Manual Exhaust Port Cleaning Level 2. Tools required: 4mm Hex Wrench, Wood or plastic scraper Parts Required: As needed: Heat Shield 1. Remove spark plug lead from spark plug, and remove muffler cover. 2. Place piston at top dead center. Remove muffler (A) and heat shield (B). 3. Use a wood or plastic scraping tool to clean deposits from cylinder exhaust port. IMPORTANT Never use a metal tool to scrape carbon from the exhaust port.
carburetor adjustment Engine Break-In New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be made. During the breakin period your engine performance will increase and exhaust emissions will stabilize. Idle speed can be adjusted as required. High Altitude Operation This engine has been factory adjusted to maintain satisfactory starting, emission, and durability performance up to 1,100 feet above sea level (ASL) (96.0 kPa).
Power Edger Operator's Manual drive shaft lubrication Level 1. Tools required: 8 mm Open End Wrench, Torx T27 L-Wrench (PE-265S), 4mm Hex Wrench (PE-265), Clean rag Parts Required: POWER BLENDXTM 8 oz. (P/N 91014) or Lithium Base Grease. 1. Loosen two (2) screws (A) and remove center locating screw (B). Pull gear box and shield from drive shaft housing. 2. Pull flexible cable from the drive shaft housing, wipe clean and recoat with a thin coating [15 ml (1/2 oz.)] of grease. 3.
2. Remove split pin (A). 3. Rotate blade until holes in inner blade adapter (B) and gear box align. Insert locking tool to lock PTO shaft (C). NOTE Blade nut (D) is left hand thread. 4. Remove blade nut (D) in a clockwise direction using T-wrench. Remove outer blade adapter (E), blade (F) and inner blade adapter (B). 5. Clean all loose debris from gear box. 6. Remove plug (G) and check level of grease. Grease should fill gear case to bottom of grease plug hole. 7.
Power Edger Operator's Manual 25 Troubleshooting EnginE PrOBLEM TrOUBLESHOOTing CHarT Problem C h eck Fuel at carburetor Fuel at cylinder Engine cranks starts hard/ doesn't start Engine runs, but dies or does not accelerate properly Engine does not crank Status C au se No fuel at carburetor Fuel strainer clogged Fuel line clogged Carburetor remedy Clean or replace Clean or replace See your Echo dealer No fuel at cylinder Carburetor See your Echo dealer Muffler wet with fuel Fuel Mixture too r
Storage warning During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may result. Long Term Storage (over 30 days) Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage maintenance which includes the following: 1.
Power Edger Operator's Manual Specifications 27 MODEL ���������������������������������������������������� PE-265, PE-265S Length (PE-265) ������������������������������������������� 1760 mm (69.3 in.) Length (PE-265S) ������������������������������������������ 1782 mm (70.16 in.) Width (PE-265) �������������������������������������������� 245 mm (9.65 in.) Width (PE-265S) ������������������������������������������� 254 mm (10.0 in.) Height (PE-265) �������������������������������������������� 315 mm (12.
Warranty Statements ECHO LIMITED WARRANTY STATEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO'S RESPONSIBILITY ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship.
Power Edger Operator's Manual PURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES • 90-day residential, or non-income producing warranty • 30-day commercial, institutional, agricultural, industrial, income producing, or rental application warranty ATTENTION TWO-STROKE ENGINE POWER PRODUCT OWNERS This ECHO two-stroke engine power product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior performance.
ECHO INCORPORATED EMISSION CONTROL WARRANTY STATEMENT FOR ECHO AND SHINDAIWA BRANDS The Environmental Protection Agency (EPA) and the California Air Resources Board (C.A.R.B.) and ECHO Incorporated (ECHO Inc.) are pleased to explain the emission control system warranty on your 2010 and later equipment/small off-road engine (SORE). New equipment/SORE must be designed, built and equipped to meet stringent EPA and C.A.R.B. anti-smog standards. ECHO Inc.
Power Edger Operator's Manual notes 31
Servicing Information parts/serial number Genuine ECHO Parts and ECHO REPOWER™ Parts and Assemblies for your ECHO products are available only from an Authorized ECHO Dealer. When you do need to buy parts always have the Model Number, Type and Serial Number of the unit with you. You can find these numbers on the engine housing. For future reference, write them in the space provided below. Model No. _________________SN.
