x7722271404 / x772000164 PE-266/S Power Edger Operator’s Manual Burn Hazard The muffler or catalytic muffler and surrounding cover may become extremely hot. Always keep clear of exhaust and muffler area, otherwise serious personal injury may occur. The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
TABLE OF CONTENTS PE-266/S TABLE OF CONTENTS Table of Contents .............................................................................................................................. 2 Introduction ........................................................................................................................................ 3 The Operator’s Manual ................................................................................................................ 3 The Safety Manual............
PE-266/S INTRODUCTION INTRODUCTION Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job dependability. Read and understand this manual and the SAFETY MANUAL. You will find both easy to use and full of helpful operating tips and SAFETY messages. The Operator’s Manual Keep it in a safe place for future reference. Contains specifications and information for safety, operation, maintenance, storage and assembly specific to this product.
SAFETY Additional or Replacement Manuals Replacement Operator, Safety Manuals, and Parts Catalogs are available from your ECHO dealer or at www.echo-usa.com or by contacting ECHO Inc., 400 Oakwood Road, Lake Zurich, IL 60047 (800-673-1558). Always check the ECHO Web Site for updated information. PE-266/S For more information scan this QR code. Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video.
PE-266/S SAFETY International Symbols Symbol Description Symbol Description Symbol Description Symbol Description Warning, See Operator’s Manual Carburetor Adjustment High speed mixture DO NOT allow flames or sparks near fuel Ignition ON / OFF Wear eye, ear and head protection Carburetor Adjustment Idle speed DO NOT smoke near fuel Primer Bulb Wear hand and foot protection Carburetor Adjustment Low speed mixture Choke Control “Run” Position (Choke Open) Choke Control “Cold Start” Positi
SAFETY PE-266/S Personal Condition and Safety Equipment Users of this product risk injury to themselves and others if the unit is used improperly and/or safety precautions are not followed. Proper clothing and safety gear must be worn when operating unit. Physical Condition Your judgment and physical dexterity may not be good: • if you are tired or sick, • if you are taking medication, • if you have taken alcohol or drugs. Operate unit only if you are physically and mentally well.
PE-266/S SAFETY The ignition components of this machine generate an electromagnetic field during operation which may interfere with some pacemakers. To reduce the risk of serious or fatal injury, persons with pacemakers should consult with their physician and the pacemaker manufacturer before operating this machine. In the absence of such information, ECHO does not recommend the use of ECHO products by anyone who has a pacemaker.
SAFETY PE-266/S All over head electrical conductors and communications wires can have electricity flow with high voltages. This unit is not insulated against electrical current. Never touch wires directly or indirectly, otherwise serious injury or death may result. Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death.
PE-266/S EMISSION CONTROL (EXHAUST & EVAPORATIVE) Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. ◆ ◆ ◆ ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit. NEVER reach into any opening while the engine is running.
DESCRIPTION PE-266/S DESCRIPTION Locate the safety decal(s) on your unit. Make sure the decal(s) is legible and that you understand and follow the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instructions for specific information. 6 11 19 5 PE-266 4 3 7 12 13 18 2 1 8 14 17 15 16 9 10 6 5 PE-266S 4 3 7 2 8 1 9 10 Hot Label Shaft Label 10 X7502026303 © 6/2014 ECHO Inc.
PE-266/S DESCRIPTION 1. POWER HEAD - Includes the Engine, Clutch, Fuel System, Ignition System and Recoil Starter. 2. THROTTLE TRIGGER LOCKOUT - This lever must be held during starting. Operation of the throttle trigger is prevented unless throttle trigger lockout lever is engaged. 3. STOP SWITCH - “SLIDE SWITCH” mounted on top of the Throttle Handle. Move switch FORWARD to RUN, BACK to STOP. 4.
CONTENTS PE-266/S CONTENTS The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, shield installation and other assembly may be necessary. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts.
PE-266/S ASSEMBLY ASSEMBLY Drive Shaft/Power Head Parts Required: Power Head, Drive Shaft Assembly 1. Stand power head upright on a level surface. 2. Loosen the drive shaft clamp bolt (A) at engine drive shaft clamp. 3. Remove dust cap if necessary, and carefully fit drive shaft assembly to engine making sure that inner drive shaft engages into clutch mount. Note: Gear Housing must be aligned properly with engine. 4. Tighten drive shaft clamp bolt (A) securely. A I 5.
ASSEMBLY PE-266/S 4. Secure ignition leads behind air filter case with clip (H). 5. Install air filter and cover. H Support Handle 1. If necessary, position support handle for comfortable operation and securely tighten screws. Note: Label shows minimum spacing for support handle location. 14 MI N SP AC ING X7502026303 © 6/2014 ECHO Inc.
PE-266/S OPERATION OPERATION Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Operation of this equipment may create sparks that can start fires. This unit is equipped with a spark arrestor to prevent discharge of hot particles from the engine.
OPERATION PE-266/S • Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize. • NEVER refuel a unit when the engine is HOT or RUNNING! • DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground. • DO NOT overfill fuel tank. Wipe up spills immediately. • Securely tighten fuel tank cap and close fuel container after refueling. • Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired.
PE-266/S OPERATION Starting Cold Engine The attachment will operate immediately when the engine starts, and could result in possible serious injury. Keep movable parts of the attachment away from objects that could become entangled or thrown, and surfaces that could cause loss of control. 1. Stop Switch Move stop switch (A) away from the STOP position. A 2. Choke Move choke lever (B) to Cold Start Position ( ). 3.
OPERATION PE-266/S Starting Warm Engine A The starting procedure is the same as Cold Start except DO NOT close the choke, and do not depress throttle trigger to wide open position. The attachment should not move at idle, otherwise serious personal injury may result. Note: If attachment moves, readjust carburetor according to “Carburetor Adjustment” instructions in this manual or see your ECHO Dealer. 1. Stop Switch Move stop switch (A) away from the STOP position. 2.
PE-266/S OPERATION Operation Techniques Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause unconsciousness, serious injury, or death. Exhaust can cause serious burns. ALWAYS position unit so that exhaust is directed away from your face and body. 1. Before edging, water the area to soften the ground to make edging easier. 2. Before edging, check the area and remove all obstacles and objects that could be thrown. 3.
MAINTENANCE PE-266/S MAINTENANCE Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and hot surfaces. Your ECHO unit is designed to provide many hours of trouble free service.
PE-266/S MAINTENANCE * Replacement is recommended based on the finding of damage or wear during inspection. Air Filter Level 1 Parts Required: REPOWERTM AIR & FUEL FILTER KIT. 1. Close choke (Cold Start Position [ ]). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumulated dirt from air cleaner area. 2. Remove air filter cover and air filter retainer from inside cover. Brush dirt from inside cover. 3.
MAINTENANCE PE-266/S Note: Federal EPA regulations require all model year 2012 and later gasoline powered engines produced for sale in the United States to be equipped with a special low permeation fuel supply hose between the carburetor and fuel tank. When servicing model year 2012 and later equipment, only fuel supply hoses certified by EPA can be used to replace the original equipment supply hose. Fines up to $37,500 may be enforced for using an un-certified replacement part.
PE-266/S MAINTENANCE 1. Remove spark plug lead. 2. Remove air cleaner cover. 3. Remove muffler cover (A). 4. Remove engine cover (B). A DO NOT use a metal scraper to remove dirt from the cylinder fins. B 5. Use brush to remove dirt from the cylinder fins. 6. Remove grass and leaves from the grid between the recoil starter and fuel tank. 7. Assemble components in reverse order. Exhaust System Spark Arrestor Screen Level 2 A Parts Required: Spark Arrestor Screen, Gasket 1. Remove spark plug lead. 2.
MAINTENANCE Exhaust Port Cleaning PE-266/S B A Level 2 Parts Required: As needed; Heat Shield 1. Remove spark plug lead from spark plug, and remove engine cover. 2. Place piston at top dead center. Remove muffler (A) and heat shield (B). 3. Use a wood or plastic scraping tool to clean deposits from cylinder exhaust port. Never use a metal tool to scrape carbon from the exhaust port. Do not scratch the cylinder or piston when cleaning the exhaust port.
PE-266/S MAINTENANCE Note: Every unit is run at the factory and the carburetor is set in compliance with emission regulations. Carburetor adjustments, other than idle speed, must be performed by an authorized ECHO dealer. 1. Check idle speed and reset if necessary. If a tachometer is available, idle speed screw (A) should be set to the specifications found on “Specifications” page of this manual. Turn idle screw (A) clockwise to increase idle speed; counterclockwise to decrease idle speed.
MAINTENANCE PE-266/S Blade Replacement Level 1. Parts Required: Blade, new split pin Note: Replace blade when it is bent, damaged, or worn shorter than 6 inches. 1. Remove split pin (A). 2. Align hole in inner blade adapter (B) with notch in gear housing, and insert locking tool (G) to prevent PTO shaft (C) from rotating. 3. Remove L.H. blade nut (D) by turning clockwise. Remove outer blade adapter (E), and blade (F). G B C F 4. Install and center blade (F) on inner blade adapter (B). 5.
PE-266/S TROUBLESHOOTING TROUBLESHOOTING ENGINE PROBLEM TROUBLESHOOTING CHART Problem Check Remedy Fuel strainer clogged Fuel line clogged Carburetor Clean or replace Clean or replace See your Echo dealer No fuel at cylinder Carburetor See your Echo dealer Muffler wet with fuel Fuel Mixture too rich Open choke Clean/replace air filter Adjust carburetor See your Echo dealer No spark Stop switch off Electrical problem Interlock switch Turn switch to ON See your Echo dealer See your Echo dealer
STORAGE PE-266/S STORAGE During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may result. Long Term Storage (Over 30 Days) Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage maintenance which includes the following: 1.
PE-266/S SPECIFICATIONS SPECIFICATIONS MODEL PE-266, PE-266S Length (PE-266) 1760 mm (69.3 in.) Length (PE-266S) 1782 mm (70.16 in.) Width (PE-266) 250 mm (9.85 in.) Width (PE-266S) 254 mm (10.0 in.) Height (PE-266) 315 mm (12.4 in.) Height (PE-266S) 335 mm (13.19 in.) Weight (dry) w/Cutter Head (PE-266) 6.61 kg (14.6 lb.) Weight (dry) w/Cutter Head (PE-266S) 6.9 kg (15.26 lb.) Engine Type Air cooled, two-stroke, single cylinder gasoline engine Bore 34.0 mm (1.34 in.) Stroke 28.
WARRANTY STATEMENTS PE-266/S WARRANTY STATEMENTS ECHO LIMITED WARRANTY STATEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO'S RESPONSIBILITY ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship.
PE-266/S WARRANTY STATEMENTS PURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES GD\ UHVLGHQWLDO RU QRQ LQFRPH SURGXFLQJ ZDUUDQW\ GD\ FRPPHUFLDO LQVWLWXWLRQDO DJULFXOWXUDO LQGXVWULDO LQFRPH SURGXFLQJ RU UHQWDO DSSOLFDWLRQ ZDUUDQW\ ATTENTION TWO-STROKE ENGINE POWER PRODUCT OWNERS This ECHO two-stroke engine power product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior performance.
ECHO, INCORPORATED 32 400 Oakwood Road Lake Zurich, IL 60047 www.echo-usa.
