Power PrunerTM Hedge Clipper Attachment Operator's Manual Model 99946400060 Serial Number 001001 & Up Models used on: PPT-230/231 PPT-260/261 PPT-2100 PPT-2400 PPFD-2400 WARNING DANGER Read rules for safe operation and instructions carefully. ECHO provides an Operator's Manual and a Safety Manual, with your Hedge Clipper Attachment. These manuals must be read and understood for proper and safe operation, otherwise serious personal injury may result.
INTRODUCTION Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-jobdependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will find both easy to use and full of helpful operating tips and SAFETY messages. IMPORTANT This attachment is designed for use with Echo's Power PrunersTM. Use of this attachment with any other ECHO Product will cause premature gear case failure and void the warranty.
SHAFT HEDGE CLIPPER ATTACHMENT OPERATOR'S MANUAL MANUAL SAFETY SYMBOLS AND IMPORTANT INFORMATION This symbol accompanied by the words WARNING and DANGER calls attention to an act or condition that can lead to serious personal injury to operator and bystanders. The circle with the slash symbol means whatever is shown within the circle is prohibited.
INTERNATIONAL SYMBOLS Symbol form/shape Symbol description/application Symbol form/shape Symbol description/application Symbol form/shape Symbol description/application DO NOT allow flames or sparks near fuel. Read and understand Operator's Manual. Fuel and oil mixture Wear eyes, ears and head protection Finger Severing Engine choke control. Wear hand protection. Use two handed. Emergency stop Hot Surface DO NOT smoke near fuel. Safety/Alert Avoid all power lines.
SHAFT HEDGE CLIPPER ATTACHMENT OPERATOR'S MANUAL EXTENDED OPERATION/EXTREME CONDITIONS Vibration and Cold It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals may be brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sensations followed by loss of color and numbness in the fingers.
SAFE OPERATION WARNING DANGER Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death. Provide Safety And Operating Instructions To All Operators • Provide all users of this equipment with the Operator's Manual and Safety Manual for instructions on Safe Operation. Keep a Solid Stance • Maintain footing and balance at all times. Do not stand on slippery, uneven or unstable surfaces.
SHAFT HEDGE CLIPPER ATTACHMENT OPERATOR'S MANUAL DESCRIPTION The ECHO product you have purchased has been factory pre-assembled for your convenience. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts.
SPECIFICATIONS MODEL ---------------------------------------------------- HEDGE CLIPPER ATTACHMENT Length ------------------------------------------------------- 775 mm (30.5 in.) Width -------------------------------------------------------- 121 mm (4.75 in.) Weight ------------------------------------------------------ 2.45 kg (5.4 lbs.) Gear Case Ratio -------------------------------------------- 3.
SHAFT HEDGE CLIPPER ATTACHMENT OPERATOR'S MANUAL WARNING DANGER Hedge Clipper cutting blades are very sharp! Always wear gloves when handling assembly, otherwise serious personal injury may result. F G C 3. Pull upper shaft tube (C) out of fiberglass lower shaft tube 127-152 mm (5-6 in.), then slide (C) back into fiberglass lower shaft tube exposing inner drive shaft (E). E (All Models) 4. Remove locator screw (F) in bottom of attachment adapter clamp. 5.
ADJUST ATTACHMENT POSITION A B 1. Hard to reach areas can be trimmed by rotating the attachment in 90° increments. Loosen (do not remove) bolts (A). Rotate attachment in adapter (B) until desired blade attachment position is achieved. Align holes and tighten bolts (A). ADJUSTING CUTTING ANGLE OF BLADE 1. Place unit on a flat, clear area. Make sure stop switch is in the “STOP” position. C 2. Move gear tension release lever (C) to “up” position. D 3. Grip hedge clipper attachment at adapter (B). 4.
SHAFT HEDGE CLIPPER ATTACHMENT OPERATOR'S MANUAL 11 MAINTENANCE Your ECHO product is designed to provide many hours of trouble free service. Regular scheduled maintenance will help achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded.
5. Check cutting blade tightness. Tighten blade bolts (A) until snug with 10 mm wrench. Loosen bolts 1/2 turn. Hold bolts (A) from turning and tighten locknuts (B) with other 10 mm wrench. B A Gear Case Tools Required: Grease Gun with ECHO® LUBETM 14 oz. cartridge P/N 91015 or Lithium Based Grease. Parts required: ECHO® LUBETM or Lithium Based Grease. 1. Clean dirt from grease fittings. 2. Carefully pump grease in each fitting. DO NOT force grease.
SHAFT HEDGE CLIPPER ATTACHMENT OPERATOR'S MANUAL SHARPENING BLADES Level 1. Tools Required: Flat File, Small Screwdriver. Parts required: Gear box gasket, ECHO® LUBETM or Lithium Based Grease. NOTE Blades are very sharp. Wear gloves to protect hands. 1. Use screwdriver to separate upper and lower cutters equal distance apart. 2. File each edge carefully. Follow the original shape of the blade. IMPORTANT If a power grinder is used DO NOT allow blade to over heat. 3. Lubricate cutting blades.
NOTES
SHAFT HEDGE CLIPPER ATTACHMENT OPERATOR'S MANUAL NOTES 15
SERVICING INFORMATION PARTS Genuine ECHO Parts and ECHO REPOWERTM Parts and Assemblies for your ECHO products are available only from an Authorized ECHO Dealer. DEALER? Call 1-800-432-ECHO or www.echo-usa.com SERVICE Service of this product during the warranty period must be performed by an Authorized ECHO Service Dealer. For the name and address of the Authorized ECHO Service Dealer nearest you, ask your retailer or call: 1-800-432-ECHO (3246). Dealer information is also available on our Web Site.
