Operator's Manual
Table Of Contents
- Table of Contents
- IIntroduction 3
- Servicing Information 3
- Parts/Serial Number 3
- Service 4
- ECHO Consumer Product Support 4
- Product Registration 4
- Additional Literature 4
- Safety 5
- Manual Safety Symbols and Important Information 5
- International Symbols 6
- Personal Condition and Safety Equipment 8
- Equipment 12
- Emission Control
- (Exhaust & Evaporative) 14
- CARB And EPA Emissions Control Information 14
- Description 15
- Contents 16
- Assembly 17
- Support Handle Installation 17
- Operation 17
- Operation With Blades 18
- Blade Selection 19
- Fuel 21
- Starting Cold Engine 24
- Starting Warm Engine 25
- Stopping Engine 27
- Applications 27
- Operating Techniques 28
- Reaction Forces 28
- Blade Cutting Problems 29
- Maintenance 30
- Skill Levels 30
- Maintenance Intervals 31
- Air Filter 32
- Fuel Filter 33
- Spark Plug 34
- Cooling System 34
- Exhaust System 36
- Carburetor Adjustment 38
- Lubrication 39
- Nylon Line Replacement 40
- Sharpening Metal Blades 41
- Troubleshooting 43
- Storage 45
- Long Term Storage (Over 30 Days) 45
- Specifications 46
- Product Registration 48
- Introduction
- Servicing Information
- Parts/Serial Number
- Service
- ECHO Consumer Product Support
- Product Registration
- Additional Literature
- Safety
- Manual Safety Symbols and Important Information
- International Symbols
- Personal Condition and Safety Equipment
- Equipment
- Emission Control
- (Exhaust & Evaporative)
- CARB And EPA Emissions Control Information
- Description
- Contents
- Assembly
- Support Handle Installation
- Operation
- Operation With Blades
- Blade Selection
- Fuel
- Starting Cold Engine
- Starting Warm Engine
- Stopping Engine
- Applications
- Operating Techniques
- Reaction Forces
- Blade Cutting Problems
- Maintenance
- Skill Levels
- Maintenance Intervals
- Air Filter
- Fuel Filter
- Spark Plug
- Cooling System
- Exhaust System
- Carburetor Adjustment
- Lubrication
- Nylon Line Replacement
- Sharpening Metal Blades
- Troubleshooting
- Storage
- Long Term Storage (Over 30 Days)
- Specifications
- Product Registration
- Notes
STORAGE SRM-225
46 X7732273804
© 11/19 ECHO Incorporated
STORAGE
During operation the muffler or catalytic muffler and
surrounding cover become hot. Always keep exhaust area clear
of flammable debris during transportation or when storing,
otherwise serious property damage or personal injury may
result.
Long Term Storage (Over 30 Days)
Do not store your unit for a prolonged period of time (30 days or longer)
without performing protective storage maintenance which includes the
following:
1. Store unit in a dry, dust free place, out of the reach of children.
Do not store in enclosure where fuel fumes may accumulate or
reach an open flame or spark.
2. Place the stop switch in the “OFF” position.
3. Remove accumulation of grease, oil, dirt and debris from exterior of
unit.
4. Perform all periodic lubrication and services that are required.
5. Tighten all the screws and nuts.
6. Drain fuel tank completely. Press purge bulb 6-7 times to remove
remaining fuel from carburetor then drain the tank again. Close choke,
start and run the engine until it stops due to lack of fuel.
7. Allow engine to cool. Remove the spark plug lead from the spark plug.
Remove the spark plug. Pour 7 cc (0.25 oz.) of fresh, clean, two-stroke
engine oil into the cylinder through the spark plug hole.
8. Pull the recoil starter handle 2-3 times to distribute the oil inside the
engine.
9. Observe the piston location through the spark plug hole. Pull the recoil
handle slowly until the piston reaches the top of its travel and leave it
there.
10. Install the spark plug. Connect the spark plug lead to the spark plug.