User`s manual

ManualsBrandsEchola Manualselectrical equipment & suppliesSPDU-108M

Echola Systems L.L.C

1161 Ringwood Ct, Ste 100

San Jose, CA-95131

Phone: 408 321 9663

http://www.echola.com/power

Models

ModelsModels

Models

PDU

PDUPDU

PDU

108M

108M108M

108M

SPDU

PDUPDU

PDU-

-116M

116M116M

116M

PDU

PDUPDU

PDU

208M

208M208M

208M

PDU

PDUPDU

PDU

216M

216M216M

216M

Smart Switched PDU Installation

Important Safety Instruction

There are no user

serviceable parts inside. Do not attempt to open any

part of

Power Distribution Unit (

PDU

)

. Doing so may expose you to

possible shock hazard and

voids

the

product

warranty.

• The PDU does not provide short-circuit protection. Therefore, Echola Systems does

not recommend plugging the unit directly into any unprotected power source, such

as a wall outlet. Always connect to an appropriately rated branch circuit’s outlet

which provides short-circuit protection using standard Circuit Breakers or Fuses.

• Always maintain reliable earthing of the PDU. Do not connect the PDU to an

ungrounded outlet or adapters or extension cords that doesn’t have ground

connection.

• The power requirement of each equipment connected to the PDU’s outlet should not

exceed individual outlet’s rated maximum capacity (refer to specification of

appropriate model for ratings).

• The aggregate power requirements of equipments connected to all outlets at any

time should not exceed the maximum input capacity of PDU (refer to specification of

appropriate model for ratings).

• Install the PDU where it may be easily disconnected for service.

•

The PDU is designed for indoor use only. Avoid exposing to extreme ambient

temperatures.

Summary of content (11 pages)

PAGE 1
Smart Switched PDU Installation Models SPDUPDU-108M SPDUPDU-116M SPDUPDU-208M SPDUPDU-216M Important Safety Instruction There are no user-serviceable parts inside. Do not attempt to open any part of Power Distribution Unit (PDU). Doing so may expose you to possible shock hazard and voids the product warranty. • The PDU does not provide short-circuit protection. Therefore, Echola Systems does not recommend plugging the unit directly into any unprotected power source, such as a wall outlet.
PAGE 2
Installing in a Rack The PDU can be installed in a standard 19” rack or enclosure. It can be mounted horizontally at front of the rack or vertically at the back as shown below. Rack Horizontal Installation Vertical Installation at the back of the Rack Outlet-1 Outlet-8 Echola Systems L.L.C 1161 Ringwood Ct, Ste 100 San Jose, CA-95131 Phone: 408 321 9663 http://www.echola.
PAGE 3
SPDU-108M Specification Input Acceptable Input voltage range Input plug type 100-120V AC NEMA L5-20P or NEMA 5-20P Maximum Input Current Input Current Monitoring Accuracy Input Frequency Cord Length 20A (16A Derated) ±5% 50/60 Hz 8/10 feet Output Output voltage Same as Input Output receptacle type NEMA 5-20R Maximum Output current/outlet Number of Outlets Outlet Current Monitoring Accuracy 16A (Aggregate current of all outlets can't exceed Max.
PAGE 4
SPDU-116M Specification Input Acceptable Input voltage range 100-120V AC Input plug type NEMA L5-30P Maximum Input Current Input Current Monitoring Accuracy Input Frequency Cord Length 30A (24A Derated) ±5% 50/60 Hz 8 feet Output Output voltage Same as Input Output receptacle type NEMA 5-20R Maximum Output current/outlet Number of Outlets Outlet Current Monitoring Accuracy 16A (Aggregate current of all outlets can't exceed Max.
PAGE 5
SPDU-208M Specification Input Acceptable Input voltage range 200-240V AC Input plug type NEMA L6-20P Maximum Input Current Input Current Monitoring Accuracy Input Frequency Cord Length 20A (16A Derated) ±5% 50/60 Hz 8/10 feet Output Output voltage Output receptacle type Maximum Output current/outlet Number of Outlets Outlet Current Monitoring Accuracy Same as Input IEC 320 C13 (7) IEC 320 C19 (1) 16A (Aggregate current of all outlets can't exceed Max.
PAGE 6
SPDU-216M Specification Input Acceptable Input voltage range 200-240V AC Input plug type NEMA L6-30P Maximum Input Current Input Current Monitoring Accuracy Input Frequency Cord Length 30A (24A Derated) ±5% 50/60 Hz 8/10 feet Output Output voltage Output receptacle type Maximum Output current/outlet Number of Outlets Outlet Current Monitoring Accuracy Same as Input IEC 320 C13 (14) IEC 320 C19 (2) 16A (Aggregate current of all outlets can't exceed Max.
PAGE 7
Initial Software Configuration You may need to change network settings of Echola PDU device before connecting it to your network's switch/router. If your network has a DHCP server then you may want to skip this section and connect PDU Ethernet port to their network's switch/router and the IP address will be assigned automatically by your DHCP server. The assigned IP address will be shown on the LCD panel. Use that IP to login into PDU and manage it.
PAGE 8
• Default Subnet mask of PDU: PDU 255.255.255.0 For example you can configure your PC/Laptops IP address as 192.168.2.222 and access the main menu of PDU. After configuring the PC/Laptop ethernet address, just use any internet browser to access PDU with new configure IP address. Now you will be prompted with PDU's login dialog; If this is first time then use default username and password.
PAGE 9
Web Interface User can configure, monitor and control the PDU through user friendly web interface. The web interface uses AJAX for providing near real-time update on current consumption for each outlets, total current, Temperature and outlet statuses. To access GUI from any smart phone/mobile devices, just use letter ‘/m’ after the ipaddress or the hostname, like http://192.168.2.21/m For more details on web interface please refer to User’s Manual at http://www.echola.com/support. Echola Systems L.L.
PAGE 10
Automation You can either use Tcl scripting language (refer to separate document for automation using Tcl) or Perl for automation. Here is an example how to use Perl script which uses api.xml file from the PDU to parse certain outputs. If you are on windows you can use strawberry perl. ############################################################ # Command Syntax: perl xmlget.
PAGE 11
Troubleshooting • If you get connection lost messages when you are on any GUI page (telnet or snmp might still work), you will have to make sure you are running latest version of JAVA on the PC where you run the browser to log into the smart PDU. The older versions of java (ver <= 5 or early 6 versions) doesn't work well with the AJAX calls that we use for real time updates. You can check whether you have latest java by clicking on following link http://java.com/en/download/testjava.