BACKUP CAMERA & INTERFACE KIT Compatible with Jeep Wrangler 2007 - 2018 JK/JKU Models EM-BUC-KIT-JW Installation Guide
Installation Guide Installation Guide EM-BUC-KIT-JW Jeep Wrangler JK Backup Camera Important EM-BUC-KIT-JW Jeep Wrangler JK Backup Camera What’s in the box Please read and follow the instructions carefully. To emphasize special information, the symbol and the words Warning, Caution and Note have special meanings. Pay special attention to messages highlighted by these signal words. These instructions are designed as a guide to help make the installation of this product successful.
Installation Guide Installation Guide EM-BUC-KIT-JW Jeep Wrangler JK Backup Camera Disassembly Recommended Tools Lug Wrench Plastic Trim Tool 7mm Socket 8mm Socket 10mm Socket Ratchet Socket Extension Torx T-30 Diagonal Cutters Wire Crimpers Electrical Tape Wire Feeder EM-BUC-KIT-JW Jeep Wrangler JK Backup Camera Drill / Drill Bits Hammer 11/16” (17mm) Deep Socket Small Pick Tool Step 1 Remove the spare tire off of the tire carrier.
Installation Guide Installation Guide EM-BUC-KIT-JW Jeep Wrangler JK Backup Camera EM-BUC-KIT-JW Jeep Wrangler JK Backup Camera Disassembly (continued) Step 3 Step 6 Fold up the rear passenger roll bar cover and pop up the plastic seatbelt guide using a plastic trim tool. Slide it up the seat belt so that it is out of the way. Remove the (2x) T30 Torx bolts that fasten the rear trim panel into place. Step 4 Step 7 Using a plastic trim tool remove the back side cover from the base of the roll bar.
Installation Guide Installation Guide EM-BUC-KIT-JW Jeep Wrangler JK Backup Camera EM-BUC-KIT-JW Jeep Wrangler JK Backup Camera Disassembly (continued) Step 12 Step 9 Remove the knee bolster panel below the steering column using a plastic trim tool to release the upper left and right clips and swing the panel downward to disengage lower locking tabs. Grab the passenger side door sill at the front most edge and pull it towards the middle of the vehicle to release the two fasteners.
Installation Guide Installation Guide EM-BUC-KIT-JW Jeep Wrangler JK Backup Camera EM-BUC-KIT-JW Jeep Wrangler JK Backup Camera Disassembly (continued) Step 18 Step 15 Using the storage tray and area over the gauges, pull the top edge of the panel to release the upper retaining clips. Lower the steering wheel and remove the panel. Remove the 7mm screw inside the switch opening. Step 16 Step 19 Remove the rubber mat from the storage tray above the radio and remove the 7mm screw underneath.
Installation Guide Installation Guide EM-BUC-KIT-JW Jeep Wrangler JK Backup Camera Mounting the Camera EM-BUC-KIT-JW Jeep Wrangler JK Backup Camera Routing the Camera Cable Step 1 Step 1 Route the camera cable through the factory opening in the top of carrier and through the opening towards the passenger side. Slide the camera mount onto the top wheel studs. Using 11/16” (17mm) deep socket and a hammer, install the push nut onto one of the wheels studs.
Installation Guide Installation Guide EM-BUC-KIT-JW Jeep Wrangler JK Backup Camera EM-BUC-KIT-JW Jeep Wrangler JK Backup Camera Routing the Camera Cable (continued) Step 4 Unclip and untape the tailgate wire harness that runs into the cargo area. Using a wire feeder, route the camera cable through the fabric wire loom. Step 7 Using a wire fishing tool route the cable through the hole in the passenger side of the dash just above the speaker.
Installation Guide Installation Guide EM-BUC-KIT-JW Jeep Wrangler JK Backup Camera EM-BUC-KIT-JW Jeep Wrangler JK Backup Camera Wire Connections Step 1 Step 4 Step 2 Step 5 Connect the Camera RCA/Power Lead Adapter to the end of the Camera Extension Cable. On the BC1-CH21-AUX harness (white plugs), disconnect the two yellow RCA’s that are marked CAMERA. Crimp the red male bullet connector to the Red camera power wire. Crimp the blue female spade connector to the Black camera ground wire.
Installation Guide Installation Guide EM-BUC-KIT-JW Jeep Wrangler JK Backup Camera EM-BUC-KIT-JW Jeep Wrangler JK Backup Camera Wire Connections (continued) Once installed, the factory screen will automatically switch to the reverse camera whenever the vehicle is placed in reverse gear. The reverse camera can also be manually activated at anytime by pressing and holding the center button on the back left side of the steering wheel for at least 4 seconds.
Installation Guide Installation Guide EM-BUC-KIT-JW Jeep Wrangler JK Backup Camera EM-BUC-KIT-JW Jeep Wrangler JK Backup Camera Wire Connections (continued) Step 2 Reconnect the vehicle battery Turn the ignition to the On position. Plug the 20-pin plug and 4-pin plugs on the BCI-CH21-HAR into interface connector 1 and 2. Step 12 Connect the black wire from the Camera RCA/Power Lead Adapter to the radio chassis as shown. Both LEDs will blink green while the module is initializing.
Installation Guide Installation Guide EM-BUC-KIT-JW Jeep Wrangler JK Backup Camera EM-BUC-KIT-JW Jeep Wrangler JK Backup Camera Wiring Diagram Step 5 Position all wiring and connectors to the left and right sides, out of the area directly behind the radio. Slide the radio into place making sure no wires are getting pinched between the radio and metal radio bracket. ..... ..... ........... ........... ..... ..... ........... ...........
AGREEMENT: End user agrees to use this product in compliance with the instructions and terms of use above and with all State and Federal laws. EchoMaster provides instructions and safety warnings with respect to this product and disclaims all liability for any use not in conformity with those instructions or other misuse of its product. If you do not agree, please discontinue use immediately and contact EchoMaster. This product is intended for off-road use and passenger use only.
