Third Brake Light Camera with Cargo and Side Blind Spot Views For Ford F-150 (2015-2019) and Ford Super Duty Trucks (2017-2019) PCAM-CHMSL2-FD15 Installation Guide
Installation Guide PCAM-CHMSL2-FD15 Third Brake Light Camera Thank you for purchasing your EchoMaster Pro automotive camera. EchoMaster cameras are designed to improve safety while driving by providing high quality images of surrounding areas and obstacles in the vicinity of the vehicle. They will also improve vehicle maneuvering capability by displaying blind spots not normally visible to the driver.
Installation Guide PCAM-CHMSL2-FD15 Third Brake Light Camera Box Contents Third Brake Light Camera and Bracket 17.5’ Extension Cable Camera Adjustment Tool Installation Guide Warranty Card Illustrations are typical and may not match exact vehicle details.
Installation Guide PCAM-CHMSL2-FD15 Third Brake Light Camera Installing the CHMSL Camera Step 1 Remove the 4 screws that secure the third brake light. Step 2 a. Remove the third brake light from the vehicle and disconnect connector. b. Place the third brake light onto the third brake light camera bracket and line up the screw holes. c. Reconnect the third brake light to the factory connector.
Installation Guide PCAM-CHMSL2-FD15 Third Brake Light Camera Step 4 Connect the extension cable to the camera. Step 5 Route the cable to the front of the vehicle and behind the radio, monitor, or mirror monitor. Step 6 Remount third brake light and camera assembly using the original screws.
Installation Guide PCAM-CHMSL2-FD15 Third Brake Light Camera Step 7 Route the reverse and turn signal wires to their respective locations according to the table below Turn Signal (Left) Blue/Green + BCM in passenger kick, black 40 pin plug (J6), pin 39 Turn Signal (Right) Yellow/Blue or Yellow/Violet + BCM in passenger kick, black 40 pin plug (J6), pin 38 Reverse Light Green/Brown + BCM in passenger kick, black 36 pin plug (J3), pin 11 J3 Black 36 pin plug J6 Black 40 pin plug 6
Installation Guide PCAM-CHMSL2-FD15 Third Brake Light Camera Step 8 Connect the yellow video RCA to the rear camera input on the radio, monitor, or mirror monitor. Step 9 Connect the Blue “Reverse power anode output” wire to the reverse trigger input on the radio, monitor, or mirror monitor. Step 10 With the ignition in the on position, shift the vehicle into reverse. Step 11 Using the supplied tool, adjust the camera’s view to desired position.
Installation Guide PCAM-CHMSL2-FD15 Third Brake Light Camera Using the CHMSL Camera Rear Cargo View Camera With the ignition in the on position, shift the vehicle into reverse. The image should appear on the screen. Left Blind Spot Camera With the ignition in the on position, apply the left turn signal. The image should appear on the screen. Right Blind Spot Camera With the ignition in the on position, apply the right turn signal. The image should appear on the screen.
Installation Guide PCAM-CHMSL2-FD15 Third Brake Light Camera 95 RI GH FT T9 LE 5° Views ° REAR 90° 9
Installation Guide PCAM-CHMSL2-FD15 Third Brake Light Camera 69 in 36in Video Output Switched +12V (Red) Ground (Black) Reverse Signal Input + (Green) Right Turn Signal Input + (Orange) Left Turn Signal Input + (Pink) Wiring Diagram 174 in Parking Lines (Green) On - Joined (Default) Off - Cut Video 1 2 GND 3 4 +12V 10
Installation Guide PCAM-CHMSL2-FD15 Third Brake Light Camera Notes: 11
AGREEMENT: End user agrees to use this product in compliance with the instructions and terms of use above and with all State and Federal laws. EchoMaster provides instructions and safety warnings with respect to this product and disclaims all liability for any use not in conformity with those instructions or other misuse of its product. If you do not agree, please discontinue use immediately and contact EchoMaster. This product is intended for off-road use and passenger use only.
