B-FOCuS™ 270/285/400PR Router Configuration Manual www.ecitele.
B-FOCuS 270/285/400 PR Configuration Manual Copyright by ECI Telecom 2001-2003. All rights reserved worldwide. The information contained in this document is proprietary and is subject to all relevant copyright, patent and other laws protecting intellectual property, as well as any specific agreement protecting ECI rights in the aforesaid information.
B-FOCuS 270/285/400 PR Configuration Manual Table of Contents 1. Introduction............................................................................................................5 2. Preparatory Actions ..............................................................................................7 2.1. Required Infrastructure.........................................................................................7 2.2. Defining the Computer in the LAN................................................
B-FOCuS 270/285/400 PR Configuration Manual 5.12. Support Services ................................................................................................39 5.12.1. Testing ATM Channels ...........................................................................39 5.12.2. Testing at IP Level ..................................................................................40 5.12.3. Updating Software Version .....................................................................40 5.13. Version ....
B-FOCuS 270/285/400 PR 1. Configuration Manual Introduction This manual describes the configuration procedures performed after installing the BFOCuS 270/285/400PR router. The manual is intended for use by skilled technicians with a solid background in telecommunications. The B-FOCuS router enables the connection of computers interconnected by a local area network (LAN) to the Wide Area Network (WAN) via an ADSL dial-up network. The FOCuS 270PR router has one Ethernet port.
B-FOCuS 270/285/400 PR ECI Telecom Ltd.
B-FOCuS 270/285/400 PR 2. Preparatory Actions 2.1. Required Infrastructure Configuration Manual To be connected to the router, the computer requires the following: • CPU: At least 266MHz. • An Ethernet Network Interface Card: Either 10Mbps or 100Mbps. • Operating System: Windows 98, NT, ME, 2000 or XP, Unix or Macintosh. • Browser: Internet Explorer, version 5.5 and above. 2.2.
B-FOCuS 270/285/400 PR Configuration Manual 4. Check that the name of the Network Interface Card you used for connecting the computer to the router’s eth0 port appears in the Connect using field. Select Internet Protocol (TCP/IP) and then click Properties. The Internet Protocol (TCP/IP) Properties dialog box appears. 5. Select the Use the following IP address radio button. Define a unique IP address for the computer, in the same subnet where the router is defined (its format should be 192.168.1.
B-FOCuS 270/285/400 PR 3. Configuration Manual Activation To activate the configuration software, you should first connect the router to the computer (or to the LAN), to the telephony network and to the electric power system (see Connection Diagram). To activate the configuration software: 1. Open an Internet browser. 2. In the address line enter the router’s IP address: 192.168.1.1. A login dialog box appears. 3. Enter the user name: admin and the password: Bezeqwow. Click OK.
B-FOCuS 270/285/400 PR Configuration Manual The display on the right side of the window differs according to the menu selection on the left side. The display presents the default router parameters. Configurable fields can be used to modify the initial settings for customizing the router to specific needs. ECI Telecom Ltd.
B-FOCuS 270/285/400 PR 4. Basic Operations 4.1. Link Status Configuration Manual Upon initializing, the current settings of communication parameters are displayed. This window presents the status of the ADSL communication, the line quality, the transfer rates in the upstream and downstream directions and additional parameters. 4.2. WAN Setup When the WAN Setup menu is selected from the Basic menu, the WAN Setup dialog box appears.
B-FOCuS 270/285/400 PR • RFC 1483 Routed. • PPPoE (PPP over Ethernet). • PPPoA (PPP over ATM). • MER (currently not applicable). Configuration Manual A newly installed router is configured as RFC 1483 bridged. In the following sections, we will explain how this default setting can be modified. As a first step, Permanent Virtual Circuits (PVC) and Virtual Channel Connection (VCC) should be defined in the ATM network. This definition is performed at the top of the WAN Setup dialog box.
B-FOCuS 270/285/400 PR Configuration Manual 4.2.3. PPP Over Ethernet In this configuration, additional management services can be activated, like authentication and efficient bandwidth management (by closing inactive sessions). Additional parameters should be defined: • User name, password and authentication protocol (in most of the cases PAP is used).
B-FOCuS 270/285/400 PR Note: Configuration Manual You cannot change the VCI and VPI values using the Modify command. Instead, delete the old line from the table at the bottom of the dialog box and add a new line with the new parameters. To delete a configuration: 1. Select the line you want to delete from the table at the bottom of the dialog box. 2. Click Delete. 3. Check that the line is deleted from the table at the bottom of the dialog box. 4.3.
B-FOCuS 270/285/400 PR Configuration Manual After a new router is installed, the RIP protocol is set by default to Off. To activate it, the status must be changed to On. In addition, you can define the RIP version to be used. For additional information concerning the RIP protocol, click RIP Information. The RIP List window appears. This list appears for the B-FOCuS 270/285PR. This list appears for the B-FOCuS 400PR. 4.5.
B-FOCuS 270/285/400 PR 4.6. Configuration Manual Erase & Reboot If you want to return to the default configuration settings, you must erase the changes you have made and restart the computer. The default configuration becomes effective only after the reboot. When selecting Erase & Reboot from the Basic menu, the following dialog box appears. Click Erase first. When an acknowledgement is received, click Reboot. ECI Telecom Ltd.
B-FOCuS 270/285/400 PR 5. Advanced Operations 5.1. ADSL Mode Configuration Manual When selecting ADSL Mode from the Advanced menu, this dialog box appears. Currently only G.DMT is supported. 5.2. DHCP The DHCP protocol enables dynamic allocation of IP addresses for efficient use of the address reservoir. The router can operate in two modes: • As a server (allocating addresses to computers in the LAN). • As a relay (relaying the request from the LAN to a specific DHCP server at the WAN).
B-FOCuS 270/285/400 PR Configuration Manual 2. Define: • Interface. Only eth0 is supported, as the router acts as a DHCP Server towards the LAN. • IP address range for allocation in the LAN. • Default gateway (the router’s IP address towards the LAN). • Subnet mask. • IP address of the Domain Name Server (DNS). Since the DNS resides in the WAN, enter the IP address of the default gateway used to access the WAN. • The number of days for leasing the address. 3. Click Apply. 4.
B-FOCuS 270/285/400 PR Configuration Manual The filtering is performed by defining users (of the router’s services); assigning for each user access permissions to the router and to the WAN; and defining filtering rules that apply to certain users and certain types of traffic. 5.3.1. Users Control The Access Control tab is used to define the router’s users and to control the permissions for accessing the router itself and the WAN via the router.
B-FOCuS 270/285/400 PR Configuration Manual 2. Click Delete. To modify the parameters of an existing user: 1. Select the required user using the radio button. 2. Click Modify. The User Modification dialog box appears. 3. Modify the required parameters (user name, password, access services and permissions) and click Apply. To change the user’s password: 1. Select the required user using the radio button. 2. Click Change Password. The Change Password dialog box appears. 3.
B-FOCuS 270/285/400 PR Configuration Manual The ACL List displays the defined access rules. To add a new rule definition: 1. Click Add. The Access List Configuration dialog box appears. 2. Select whether you want to apply the rule to specific users (from the list of users defined at the Access Control tab) or to all users. If you check the User Name checkbox, you must define a specific user. Otherwise, the rule applies to all users. 3.
B-FOCuS 270/285/400 PR Configuration Manual As a default, the proxy and the authentication process are disabled. If you want to apply the ACL rules, you must enable the proxy. Note: The proxy must be defined in the router as well as in all the LAN computers. 5.3.4. IP Level Filtering As a default, the firewall enables opening any session from the LAN to the WAN, but no session in the opposite direction. The traffic filtering is performed by rules (Policies) that are applied to it in a prioritized order.
B-FOCuS 270/285/400 PR Configuration Manual 2. Define the rule’s parameters: • Precedence (an integer from 1 to 64K). • Source IP address and subnet mask. • Destination IP address and subnet mask. • Source port range. • Destination port range (use the list). • Protocol. • When TCP is selected, you may define also specific flags. 5. Apply the rule to the traffic via the firewall. You can do this in one of two ways: • • Define a new Action ID.
B-FOCuS 270/285/400 PR Configuration Manual In this case, enter the number of an existing Action ID. The rule’s application parameters are copied from the original definition. You can redefine the precedence to apply this rule at a higher priority. 6. Click Apply. To view the rules you have defined: In the IP Filtering tab click View Actions. The List of Firewall Parameters dialog box appears. You can see the parameters common to all rules having the same Action ID. 5.4.
B-FOCuS 270/285/400 PR Configuration Manual NAPT translates its IP address and port number to other values. When the answer arrives from the WAN, the NAPT server knows how to route it to the originating computer. From the WAN side it is impossible to initiate access to a specific computer within the LAN, unless the proper permissions have been defined. The router supports three modes of operation: • Static IP address in WAN. • Mapping address from WAN to LAN. • Mapping port numbers from WAN to LAN.
B-FOCuS 270/285/400 PR Configuration Manual To add a line to the list: 1. Click Add. The Static NAT Configuration dialog box appears. 2. Define the IP address towards the WAN and the IP addresses range for allocation in the LAN. Note: To enable traffic from the WAN to the LAN, define the same IP address in the Local Address From and in the Local Address To fields. In addition, open the applicable port in the Firewall (see IP Level Filtering ). 3. Click Apply. 5.4.3.
B-FOCuS 270/285/400 PR Configuration Manual 2. Define the public address, the public port range, the local address, the local port range and the layer 4 protocol (UDP or TCP). 3. Click Apply. Note: 5.5. In addition to these definitions, open the applicable port in the Firewall (see IP Level Filtering ). Configure The Configure menu enables detailed definition of the communication parameters in various sessions.
B-FOCuS 270/285/400 PR Configuration Manual • mer0 – is not applicable. • adsl0 - is the interface towards the WAN (not definable). • lo0 – is the loop-back interface (not definable). • atm0-atm7 - are the interfaces for IOPA networks. • pppo-ppp7 – are the interfaces for the internal dialer within the router (not definable). The values presented in the above figure are the default values. At the bottom of the tab there are control buttons that enable operations on the displayed data.
B-FOCuS 270/285/400 PR Configuration Manual 2. Define: • IP address and subnet mask. • Maximal size of a package (MTU). 3. To activate the interface set the status to UP. 4. Click Apply. To define DNS and Default Gateway to all interfaces: 1. Select the radio button on the required line and click DNS & Default G/W. The DNS & Default Gateway Configuration dialog box appears. 2. Define: • Domain name in the WAN. • Primary and secondary DNS in the WAN.
B-FOCuS 270/285/400 PR Configuration Manual 5.5.2. Defining Virtual Channels The VCC tab displays the defined virtual channels. To see virtual channels in the IPoA network: Click List Ipoa. To Delete the encapsulation in a specific channel: Select the required radio button and click Delete Encap. To add a new Channel: 1. Click Add. The VCC Configuration dialog box appears. 2. This dialog box resembles the WAN Setup dialog box in the Basic Operations menu, yet it enables more detailed definitions.
B-FOCuS 270/285/400 PR Configuration Manual To view ATM parameters: Click Show VCC Quality. A list of VCCs and their parameters appears. 5.5.3. Defining PPPoE The PPPoE tab displays detailed parameters of the dial-up over Ethernet channels. Note that the table’s header consists of two lines, and two lines of data are displayed accordingly for each channel. A few channels can be defined simultaneously, and then one of them can be selected as a default.
B-FOCuS 270/285/400 PR 5.6. Configuration Manual IGMP Proxy The IGMP Proxy is used for transferring video and television channels over telephony infrastructure. You can see a summary table of all the interface definitions as well as the parameters of each interface separately. The IGMP-Proxy is configured on WAN interfaces. The IGMP-Proxy-router is configured on any available LAN interface.
B-FOCuS 270/285/400 PR 5.7. Configuration Manual Bridging Ethernet frames are bridged over ATM virtual channels (per RFC 1483). The frames are encapsulated either in LLC mode or in Vc Multiplexing mode. The Bridging menu enables viewing and defining the router’s parameters, when operated as a bridge. 5.7.1. Bridge Parameters The Bridge tab displays the defined bridge parameters. To delete an existing bridging group: Click Flush. To define a group of interfaces as a bridging group: 1.
B-FOCuS 270/285/400 PR Configuration Manual 2. Select an interface from the list. You can only select interfaces that have previously been defined as members of the bridging group. 3. Define virtual channels (Vpi and Vci). 4. Select the type of encapsulation. 5. Click Apply. 6. Check that the interface has been added to the list. To delete an existing bridging group: Click Flush. To activate the defined bridge entries: Click Enable. Note: The workflow is as follows: Define an EoA configuration.
B-FOCuS 270/285/400 PR Configuration Manual 2. Define the required port parameters and click Apply. To activate the definition Click Enable. 5.7.3. Defining Filtering The Filters tab presents the filtering parameters of Ethernet nodes. For every node in the tree (defined by means of a MAC address of a communication unit in the network), you can define the filtering parameter – whether data arriving from this node towards the WAN will be blocked or passed.
B-FOCuS 270/285/400 PR Configuration Manual 2. Define the MAC address and Frame (Forward or Block). Click Apply. To modify filtering definitions: 1. Use the radio button to select the node you want to modify and click Modify. The Filter Configuration dialog box appears. 2. Modify the MAC address and define Frame (Forward or Block). Click Apply. To delete filtering definitions: Use the radio button to select the node you want to delete and click Delete. Note: 5.8.
B-FOCuS 270/285/400 PR 5.9. Configuration Manual Firewall Statistics The Firewall Statistics menu presents data for traffic that has passed via the firewall or has been blocked. The Traffic tab displays statistics for all sessions that have reached the firewall. The HTTP tab displays only sessions in the HTTP proxy protocol, sorted by the users that have initiated them. ECI Telecom Ltd.
B-FOCuS 270/285/400 PR Configuration Manual 5.10. System Statistics The System Statistics menu presents general data on the system in which the router operates. The Interface tab displays general data about all interfaces, their statuses and the traffic that has passed through them. The TCP/IP tab displays data on the traffic in the IP, UDP, TCP and ICMP protocols.
B-FOCuS 270/285/400 PR Configuration Manual 5.11. ATM Statistics The ATM Statistics tab displays data for traffic in the ATM network. The AAL5 tab presents traffic data at the AAL5 layer, used to transfer data channels. The SNDCP tab presents encapsulation data. 5.12. Support Services The Diagnostics menu enables support services, including the activation of various levels of fitness tests and updating the router’s software version. 5.12.1.
B-FOCuS 270/285/400 PR Configuration Manual 5.12.2. Testing at IP Level At the IP level, you can check the connectivity to other computers using the Ping command. Define the destination computer’s IP address and click Submit. 5.12.3. Updating Software Version When a new version of the router’s software is released, it is sent to you in the form of a file with the extension .bin. To load a new software version to the router: 1. Click Browse. 2. Locate the new version’s *.bin file. 3. Click Upgrade.
B-FOCuS 270/285/400 PR 6. Configuration Manual Workflows This section describes typical workflows for using the B-FOCuS 270/400PR User Interface for performing typical operations. 6.1. Changing User Name and Password (only in 400PR) 1. Login as a PPPoA user, using user name: pppoa and password: user. The PPPoA Configuration dialog box appears. 2. Change the user name to the name received from your ISP. Use the format @. For example: john@ISP. 3.
B-FOCuS 270/285/400 PR 6.2. Configuration Manual Defining a Bridge per RFC 1483 You can define a bridge in two ways. The basic workflow is simple, but most of the parameters are defined by default. The advanced workflow enables detailed definition of most parameters. 6.2.1. Basic Workflow To define a bridge per RFC 1483 in the basic way: 1. From the Basic operations menu select WAN Setup. The WAN Setup dialog box appears. 2. Click the RFC 1483 Bridged radio button. 3.
B-FOCuS 270/285/400 PR Configuration Manual 6.2.2. Advanced Workflow To define a bridge per RFC 1483 in the advanced way: 1. You have to assign the interfaces you want to define to the bridging group. From the Advanced operations menu select Bridging. 2. Click Flush. 3. In the Bridge tab, click GroupInfo. The Group Interfaces dialog box appears. 4. Check the interfaces you want to add to the group (in this example: etho, atm0, atm1). 5. Click Apply. This line is added to the List of Bridge Entries. 6.
B-FOCuS 270/285/400 PR Configuration Manual 9. To define the encapsulation, select Bridging from the Advanced menu and click Add PVC. The Bridge Configuration dialog box appears. 10. Select one of the atm interfaces (in this example, atm1). Enter the VCI and VPI values and select the type of encapsulation. 11. Click Apply. The values you have defined appear in the atm line (in this example, atm1). 12. To activate the bridge, click Enable. 13. From the Advanced menu select Configure.
B-FOCuS 270/285/400 PR 6.3. Configuration Manual Defining a Routed IPoA per RFC 1483 You can define a router in two ways. The basic workflow is simple, but most of the parameters are defined by default. The advanced workflow enables detailed definition of most parameters. 6.3.1. Basic Workflow To define a routed IPoA per RFC 1483 using the basic method: 1. From the Basic operations menu select WAN Setup. The WAN Setup dialog box appears. 2. Click the RFC 1483 Routed radio button.
B-FOCuS 270/285/400 PR Configuration Manual 3. Define the selected interface, the IP address and subnet mask in the WAN, and the MTU value. Set the status to UP. Click Apply. 4. Check that the newly defined interface appears in the table in the Interface tab and that its status is UP. 5. Select the VCC tab and click Add. The VCC Configure dialog box appears. 6. Click the Routed radio button. Select the interface you want to define (atm4) from the list. Define VPI, VCI and all other parameters. 7.
B-FOCuS 270/285/400 PR Configuration Manual 11. From the Basic menu select WAN Setup. Check that the channel you have defined appears in Router mode and that NAPT is in the On state. 6.4. Defining Classical IPoA per RFC 1577 Classical IPoA per RFC 1577 can only be done using the Advanced method. To define Classical IPoA: 1. From the Advanced menu select Configure. 2. From the list of interfaces select an available ATM interface (in this example atm5) and click Configure Interface.
B-FOCuS 270/285/400 PR Configuration Manual 8. There are two options: • If you check the Default PVC checkbox, you should define specific VC and VP and the traffic shaping parameters. • If you uncheck the Default PVC checkbox, define the next hop IP address – an address in the WAN from which the routing continues. 9. In both cases click Apply. Check that the newly defined interface appears in the VCC list. 10.
B-FOCuS 270/285/400 PR Configuration Manual 13. Select the interface (atm5). Check the Enable NAT checkbox. Click Apply and then click Continue. 14. Check that the interface you have defined appears in the WAN Setup table with NAPT in the On state. 6.5. Defining PPP Over ATM You can define PPP over ATM in two ways. The basic workflow is simple, but most of the parameters are defined by default. The advanced workflow enables detailed definition of most parameters. 6.5.1.
B-FOCuS 270/285/400 PR Configuration Manual 6.5.2. Basic Workflow To define PPP over ATM using the advanced method: 1. From the Advanced operations menu select WAN Configure. 2. In the VCC tab click Add. The VCC Configuration dialog box appears. 3. Select the PPPoA radio button. Define: VPI, VCI, Profile ID, user name (@) and password, authentication protocol (PAP), a ppp interface, encapsulation type (VC), subnet mask and trace. Enable NAT.
B-FOCuS 270/285/400 PR Configuration Manual 8. Check that the interface you have defined appears in the VCC list. Note: After connection to the WAN, you will be able to see the IP address allocated by the ISP (either in the WAN Setup menu or when you login as a PPPoA user). 9. Click Show VCC Quality and check that the traffic shaping parameters appear as you have defined them. 6.6. Defining PPP Over Ethernet You can define PPP over Ethernet in two ways.
B-FOCuS 270/285/400 PR Configuration Manual 6.6.2. Advanced Workflow To define PPP over Ethernet using the advanced method: 1. From the Advanced operations menu select Configure. 2. In the VCC tab click Add. The VCC Configuration dialog box appears. 3. Select the PPPoE radio button. Define: VPI, VCI, Profile ID, user name (@) and password, authentication protocol, a ppp interface, mode of operation (Direct or Auto and idle time), encapsulation type (LLC), subnet mask and trace. Enable NAT.
B-FOCuS 270/285/400 PR 6.7. Configuration Manual Updating Software Version To load a new software version: 1. From the Advanced menu select Diagnostics and click the Upgrade tab. 2. Click Browse. 3. Locate the new version’s *.bin file. 4. Click Upgrade. Very Important: Do not switch the router off during the upgrade process! You must wait until a success message appears. Afterwards, restart the router to apply the new version. 5. This message appears when the upgrade process has been completed.
B-FOCuS 270/285/400 PR ECI Telecom Ltd.
B-FOCuS 270/285/400 PR 7. Configuration Manual Troubleshooting This section describes possible problems arising when the router is used, and suggests possible solutions. 7.1. Defining User Name and Password (Only in 400PR) Phenomenon: You cannot dial up to the WAN. Possible solution: The defined user name and/or password are incorrect. To solve the problem: 1. Login as a pppoa user. Use the default user name: pppoa and the default password: user. The PPPoA Configuration dialog box appears. 2.
B-FOCuS 270/285/400 PR 7.2. Configuration Manual Proper Version Upgrading Phenomenon: You cannot access the Configuration definition graphical user interface (GUI). When defining the address 192.168.1.1, an error message appears. Possible solution: The new version has not been installed properly. There might have been a power failure during the upgrade, or the new file was faulty or wrong.
B-FOCuS 270/285/400 PR Configuration Manual 14. Switch the router’s power off. Wait for 5 seconds and switch it on. Try to access the Configuration GUI via the browser. 15. Use the Version option in the Advanced menu to check that the proper version is installed. 7.3. Hardware Reset In case you need to return to the default configurations and you cannot access the router via the configuration GUI, perform hardware reset. Note: Hardware reset should be performed only in necessary cases.
B-FOCuS 270/285/400 PR ECI Telecom Ltd.
B-FOCuS 270/285/400 PR 8. Configuration Manual Specifications This section contains useful information about the router: • Connection diagram. • Indicators. • Technical specifications. 8.1. Connection Diagrams The following figures show how the routers are connected to the computers, telephone network and power source. 8.1.1. B-FOCuS 270 Connections ECI Telecom Ltd.
B-FOCuS 270/285/400 PR Configuration Manual 8.1.2. B-FOCuS 285PR Connections 8.1.3. B-FOCuS 400PR Connections ECI Telecom Ltd.
B-FOCuS 270/285/400 PR 8.2. Configuration Manual Indicators The router’s front panel contains these LED indicators: LED Condition Power Off On Power is off. Power is on. Off The modem is operating properly. On The modem has a problem. Please call your service provider. Off The modem’s 10Base-T port is not connected to the computer.
B-FOCuS 270/285/400 PR Configuration Manual 8.2.1. B-FOCuS 270PR 8.2.2. B-FOCuS 285PR ADSL Sync Power Alarm LAN 10 USB LAN100 ECI Telecom Ltd.
B-FOCuS 270/285/400 PR Configuration Manual 8.2.3. B-FOCuS 400PR ECI Telecom Ltd.
B-FOCuS 270/285/400 PR 8.3. Configuration Manual Specifications 8.3.1. Standard Compliance • ADSL (ANSI T1.413 Issue 2). • G.992.1 (G.dmt – including Category I). • G.992.2 (G.lite). • G.992.3 (ADSL2) Supported as of Q4/2003 • G.992.5 supported as of Q1/2004. • G.994.1 (G.hs – including handshake protocol). • Multi-Protocol Over AAL5 (RFC 1483 &2684). • ATM Forum UNI version 3.1 & 4.0 PVC. • Supports VC-based and LLC multiplexing for 32 VCs. • PPP over AAL5 (RFC 2364).
B-FOCuS 270/285/400 PR Configuration Manual 8.3.2. Software 8.3.2.1. Routing • IP (RFC 791), UDP (RFC 768), ICMP (RFC 792), ARP (RFC 826). • IGMP for IP Multicast. • RIP V1/V2. • Static routing. • DHCP relay, client, and server (RFC 2131 and 2132). • DNS relay & client. • NAPT supports maximum 2000 simultaneous connections. • NAT/PAT (RFC 1631 & 2663 & 3235) supports multimedia applications such as NetMeeting, CuSeeMe, HTTP, FTP, ICMP, Pop3, Telnet, RealPlayer H.
B-FOCuS 270/285/400 PR Configuration Manual 8.3.4. Security 8.3.4.1. Stateful Firewall Security Extracts state-related information required for the security decision from all application layers. 8.3.4.2. Packet Filter Firewall Capable of filtering all information available in the IP packet: • Source and destination interface. • IP address and port. • TCP incoming/outgoing connections. • TCP header (SYN/ACK/URG). • Type of service, protocol, and ICMP type.
B-FOCuS 270/285/400 PR Configuration Manual 8.3.7. Power • • 110/220V AC +/-10%, 50 ~60Hz, • 270PR and 285PR: 9V 800mA. • 400PR: 9V 1.2A. Power Consumption: • 270PR and 285: lower or equal to 5W. • 400PR: lower or equal to 6W. • Auto Restart: Following a power failure and restoration, the router restarts automatically. • Spectral Mask: Complies with ITU-T Recommendations G992.3 (Annex A). Average PSD within the pass band is lower than -38 dBm/Hz. Pass band ripple is lower than +3.5 dB.
