ELECTRIC TELESCOPIC HEDGE TRIMMER Model HDT01 OWNER’S MANUAL IMPORTANT: Read and understand this manual before assembling or operating this Trimmer. Improper use can cause severe injury. Keep this manual for future reference. Any questions or problems – please call the Eckman Helpline on 0871 590 5917 or go to www.eckman.co.
Contents I Parts List II- Technical Data III-Safety Instructions IV-Getting Started V- Operation VI- Cleaning, Maintenance, storage and guarantee. I Parts List 1. 450mm Long Reciprocating Heat-Treated Dual Cutter Blade 2. Pivoting Power Head 3. Hand Adjustment Knob For Cutting Head 4. Knob Release Button 5. Hand Adjustment Knob For Shaft 6 .Telescopic Shaft 7. Telescopic Shaft Lock 8. Auxiliary Handle 9. Trigger Switch Lock Out 10. Handle 11.
II. Technical Data Rated Voltage: 230v- 240v- 50hz Input Power: 450w Idling Speed: 1500rpm Cutting Capacity 14mm diameter Weight: 4.5 kg NOISE AND VIBRATION DATA Weighted sound pressure level: 79dB Weighted sound power level: 96dB Vibration: 3.5M2/S Overall length 1.74m / Overall length fully extended 2.06m SYMBOLS Do not expose to rain.
III. SAFETY INSTRUCTIONS WARNING: When using electric Trimmers, basic safety precautions should always be followed to reduce the risk of personal injury. Read all instructions carefully prior to operating this trimmer. 1. Stay Alert---- Watch what you are doing. Use common sense when operating Trimmer. 2. Avoid Dangerous Environments Do not operate Trimmer In rain or in damp or wet locations. 3. 4. 5. 6. While under the influence of alcohol, medications, or drugs.
2. Be aware of extension cord while operating Trimmer. Be careful not to trip over extension cord. Keep extension cord away from cutter blades at all times. 3. Avoid Unintentional Starting —Do not carry plugged-in Trimmer with finger on switch. Be sure switch is OFF when plugging in Trimmer. 4. Do Not Over-reach-------Keep proper footing and balance at all times. DANGER----RISK OF INJURY Keep hands away from blades at all times. Keep both hands on handle areas when Trimmer is on.
Step1: Please see PIC 2 and PIC 3. Line up the shafts and push the male connector pins into the female connection. They will only fit together one way due to the special extrusions on the shaft ends, one of which is slotted as shown in PIC3 and the other one which has a protrusion as shown in PIC 2. PIC.3 PIC.4 PIC.5 Step 2: Having fitted the two shafts together, slide the red outer sleeve attached to the handle shaft down and over the red thread on the end of the trimmer head shaft.
Adjusting The Angle Of The Trimmer Head: PIC.6 PIC.7 To change the angle of the trimmer head (from 0 – 90 degrees), grip the large red adjustment knob (Part3) and depress the grey coloured knob release button as shown in PIC 6 & PIC 7. When you’ve reach the desired trimmer head position, release the pressure on the grey button. ROTATING THE SHAFT Apart from being able to change the cutting angle by up to 90 degrees, you can also adjust the shaft from 0-180 degrees.
PIC.8 USING THE TRIMMER The Trimmer is a dual-purpose tool. It is designed to trim and shape tall, hard-to-reach hedges and bushes with its extended reach and pivoting head. You can also adjust the Trimmer to trim and shape smaller hedges and shrubs near the ground without having a bend or stoop. Please visit the Eckman website www.eckman.co.uk and watch the short demonstration video. VI. CLEANING, MAINTENANCE AND STORGE WARNING: Disconnect Trimmer from power supply before cleaning or servicing.
Once the Trimmer is cleaned, apply a high coat of oil to the cutter blades to prevent rust and provide lubrication. MAINTENANCE AND STORAGE OF TRIMMER 1. Maintain Trimmer With Care ● Keep cutting edge sharp and clean for best performance and to reduce the risk of injury. ● Periodically apply a light coat of oil to the cutter blades for lubrication. ● Inspect Trimmer cord periodically, and if damaged, have it repaired by an authorized service facility.
