MODEL CD3424 ESN E3 High-Power CD Receiver with MP3 Decoder and Remote OWNER'S MANUAL We appreciate your purchase of this receiver. Please read through this manual for correct operation. We suggest that after reading it you keep this manual in a safe place for future reference.
For your safety in using the CD3424 Warnings and caution signs, illustrated below, are posted throughout this manual as well as on the CD3424. They show safe and correct ways to handle the product so as to prevent personal injury to you and others and to avoid property damage. Before reading through the manual, take time to read through and learn the important information listed in this section.
Warning • Do not place the vinyl storage bag over a person. It may cause a serious accident or death by suffocation. • Do not adjust the controls while driving the car. To adjust the controls, stop the car in a safe location. • To prevent accidents, store batteries for the remote control out of the reach of small children. In case a child swallows a battery, consult a physician immediately. • Do not disassemble or rebuild this product. Doing so may cause an accident, fire or electrical shock.
Warning • To prevent a short circuit from occurring, disconnect the battery's negative terminal before installing this product. Otherwise, an electric shock or injury may result. • When using an existing nut and/or bolt from the vehicle to ground this product, do not use any that secure parts of the steering or braking systems. Otherwise, an accident may result. • Bundle cables and harnesses with electrical tape or wire ties to prevent them from interfering with moving parts.
Caution • Play the audio at a moderate volume level that permits you to hear sounds from outside the car. Driving without being able to hear outside sounds may result in an accident. • Keep foreign objects out of the disc slot. They may cause fire or electrical shock. Another possibility is that discs may be damaged or become stuck. • Do not stick your fingers or hands into the disc slot. Doing so may cause personal injury.
Caution • Avoid installing this product in places where it may get wet, such as near windows, or in places that are moist or dusty. Presence of liquid, moisture or dust inside this product can cause short circuiting, resulting in smoke or fire. • Do not install this product in locations where it cannot be fastened securely, such as places subject to frequent vibration. Otherwise, it may become dislodged and cause an accident or injury. • Do not block this product's vent or heat sink.
Table of Contents Operating precautions ............................................ 11 Notes on operation ..................................................................... 11 About compact discs .................................................................. 12 About cleaning a CD .................................................................. 14 Names of controls and parts .................................. 15 ESN security operating procedure ......................... 16 About ESN .............
How to operate the CD player ................................. 30 Listening to CDs ......................................................................... 30 Advancing to the next track or returning to the beginning of the track being played ...................................................................... 31 Fast Forward/Rewind ................................................................. 31 Playing the beginning of tracks (SCAN) .....................................
Changing the reception sensitivity for automatic scanning ........ 45 Changing the radio band location ............................................... 45 FM reception characteristics ...................................................... 46 FM reception differs from AM ............................................... 46 Fading out ............................................................................ 46 Reception area of FM broadcasts ........................................ 47 Multipath ..............
How to operate the receiver with an optional CD changer connected............................................. 60 Listening to a CD......................................................................... 60 Advancing to the next track or returning to the beginning of the track being played ................................................................. 60 Fast Forward/Rewind .................................................................. 60 Playing the beginning of tracks (SCAN) ......................
Operating precautions Operating precautions Notes on operation • For your safety, play only at volume levels that allow outside sounds to be heard. • We recommend using with this player a disc with the logo shown to the left. • You can play music CDs(CD-R/CD-RW) on this player. Be sure to use discs that have been properly processed. Depending on the editing equipment used, some discs may not play properly.
Operating precautions About compact discs • The signal recorded on a compact disc is read by a laser beam, so nothing touches the disc surface. A scratch on the recorded surface or a badly warped disc may cause deteriorated sound quality or intermittent playback. Observe the following precautions to ensure high quality sound performance: • Do not leave an ejected disc in the disc slot for very long; the disc may warp. Discs should be stored in their cases and kept away from high temperature and humidity.
Operating precautions About brand new CDs • You may notice that some brand new discs are rough around the center hole or outside edge. Remove the rough edges with the side of a ballpoint pen, etc. Rough edges may prevent proper loading in the deck. Flakes from the rough edges may also stick to the recorded surface and interfere with playback. About CD accessories • Do not use accessories (stabilizers, protective seals, laser lens cleaners, etc.) sold for “improving sound performance” or “protecting CDs.
Operating precautions About borrowed CDs • Do not use a CD with glue or remnants of adhesive tape or labels. They may cause the CD to get stuck inside or damage the deck. About irregularly-shaped CDs • Specially-shaped CDs, like heart-shaped or octagonal CDs, cannot be played. Do not attempt to play them, even with an adapter, since they may damage the player. How to remove CDs • When removing the ejected disc, pull it straight out along the slot.
Names of controls and parts Names of controls and parts ①② ③ ④ ③ ⑤⑥ ⑦ ⑬ ⑫⑪ ⑩ ⑨ ⑧⑥ [DISC] button Switches disc modes. [ Ejects compact disc. (EJECT) ] button Selects radio preset channels and performs disc mode Buttons [1] to [6] functions. Disc slot Inserts compact discs. [DISP] button Switches screen display. [SEEK /FAST ] button Automatically finds radio reception and fast forward/rewind. [SEL] button Selects radio stations and CD tracks.
ESN security operating procedure ESN security operating procedure About ESN This deck incorporates ESN (ECLIPSE Security Network). The ESN is a security system which disables all deck functions when the power is restored if the deck is stolen from the vehicle. Turning the power of the deck off or switching the vehicle's ignition switch off activates the security feature. Setting or canceling of the security feature can be done with a "Key CD".
ESN security operating procedure Button [6] [FUNC] button How to operate the ESN (Key CD) security How to program the Key CD 1 Check that the Power is OFF. 2 Press and hold button [6], then the [FUNC] button, and hold both for more than one second. A [SEC] message appears, then in two seconds it will change to [DISC]. The CD3424 is now ready to accept your Key CD in the CD slot. ATTENTION If a CD has already been inserted, a [SEC] message appears, and then the CD is ejected.
ESN security operating procedure Button [6] [FUNC] button How to cancel the Key CD 1 Turn OFF the Power. 2 Press and hold button [6], then the [FUNC] button, and hold both for more than one second. A [SEC] message appears, then in two seconds it will change to [DISC]. The CD3424 is now ready to accept your Key CD in the CD slot. ATTENTION If a CD has already been inserted, a [SEC] message appears, and then the CD is ejected. 3 Insert your Key CD into the slot.
ESN security operating procedure How to change the Key CD 1 First, cancel the existing Key CD. Refer to “How to cancel the Key CD.” 2 Next, program a new Key CD. Refer to “How to program the Key CD.” How to resume normal operation (ESN security lock out) If power is disconnected while ESN security is active (a Key CD was programmed), operation is disabled until power is restored and the unit unlocked. Follow this procedure to resume normal operation.
ESN security operating procedure Button [6] [FUNC] button What happens if an incorrect CD is inserted? 1 After the 5th incorrect attempt, the display reads [HELP] for five seconds. [HELP] will appear for five seconds, after which the serial number will appear. 2 Press button [6], then the [FUNC] button, and hold them for five seconds. After the [SEC] message will appear for two seconds, rolling code will appear. 3 Press the [FUNC] button. A [DISC] message appears.
ESN security operating procedure Button [2] Button [4] [FUNC] button How to turn the security indicator on/off Once ESN security is activated, the indicator flashes whenever the vehicle’s ignition is turned off, warning potential thieves that the unit is protected. However, if you do not want this visible deterrent, it may be turned off. 1 With the power OFF, press button [2], then the [FUNC] button and hold both for more than one second. 2 [IND. FLASH] or [IND. -----] appears on the display. [IND.
Basic operation Basic operation [PWR] button This section covers basic operating procedures. For additional details, please refer to the sections on specific functions. Turning the power on and off Turning the power on and off. When the power is turned on, the state used when the power was turned off such as CD and tuner playing is restored. When the vehicle has no ACC position on the ignition switch, care is needed when turning off the deck. Follow Step 2 or Step 3 when turning off the power.
Basic operation [DISC] button Listening to a CD 1 Insert a CD into the disc slot, label side up. The CD will start playing. ATTENTION When a CD is already loaded, press the [DISC] button to switch to the CD mode.
Basic operation Buttons [1] to [6] [FM AM] button [SEEK ] button [SEL] button [FAST [AUDIO CONTROL] button ] button Listening to the tuner 1 Press the [FM AM] button. This will turn the tuner on. 2 Press the [FM AM] button to switch to the desired FM or AM bands. Radio bands will switch from FM1 ➔ FM2 ➔ FM3 ➔ AM in order each time the button is pressed. 3 Turn the [SEL] button to the left or right to tune to a station. Turn to the right: Turnes to higher frequencies.
Basic operation [AUDIO CONTROL] button Switching audio control modes Various audio control modes may be fine-tuned using this procedure. 1 Press the [AUDIO CONTROL] button for less than one second to select the item to be adjusted. Modes will switch in the order shown below each time the button is pressed. VOL NF-PH BASS TREB XO-NF BAL XO-FR FAD NON-F VOL (VOLUME) Mode Adjusts volume. Turn the [AUDIO CONTROL] button to the left or right. Turn to the right: Increases the volume.
Basic operation [AUDIO CONTROL] button BAL (BALANCE) Mode Adjusts left/right speaker balance. Turn the [AUDIO CONTROL] button to the left or right. Turn to the right: Emphasizes right speakers. Turn to the left: Emphasizes left speakers. FAD (FADER) Mode Adjusts front/rear speaker balance. Turn the [AUDIO CONTROL] button to the left or right. Turn to the right: Emphasizes front speakers. Turn to the left: Emphasizes rear speakers.
Basic operation [AUDIO CONTROL] button XO-NF (NON-FADER) Mode Here, the LPF (low-pass filter) to the non-fader pre-out can be switched ON and OFF. Since the low-pass filter passes only lower ranges (higher ranges are cut off), efficient playback is enabled by cutting off mid to higher range elements not needed for a woofer. Turn the [AUDIO CONTROL] button to the left or right switch Cross Over (NF) ON/OFF.
Basic operation [SEL] button [RTN] button [FUNC] button Making changes with Function Mode A variety of settings can be changed. 1 Press the [FUNC] button. The function mode is activated. 2 Turn [SEL] button in either direction to display setting items for selection. Setting items will be displayed in the following order when the [SEL] button is turned to the right.
Basic operation [SEEK ] button [SEL] button [FAST button [RTN] button ] [FUNC] button Setting the time This receiver uses the 12-hour display notation. 1 Turn [SEL] button to select CLOCK ADJ. 2 Press the [SEL] button. The clock adjustment mode is activated. 3 Turn [SEL] button to display the item to be selected for adjustment. Hours, minutes or exact hour will be switched each time the button is turned. 4 Press the [SEEK /FAST ] button. [SEEK ] button: Turns the time forward.
How to operate the CD player How to operate the CD player [DISC] button First press the [DISC] button to switch to the disc mode. It is assumed here that a CD has already been loaded into the unit. Listening to CDs 1 Press the [DISC] button. This starts CD play. If an external CD changer is connected, each additional press of the [DISC] button will switch modes from CD changer 1 ➔ CD changer 2 ➔ CD player. A changer or player with no discs loaded will be skipped.
How to operate the CD player Button [4] [SEEK ] button [SEL] button [FAST ] button Advancing to the next track or returning to the beginning of the track being played 1 Turn the [SEL] button to the left or right. Turn to the right: Advances to the next track. Turn to the left: Returns to the beginning of the track being played. (Repeat turning for previous tracks.) Fast Forward/Rewind Fast forward or rewind the song currently being played. 1 Press and hold the [SEEK ] or [FAST ] button.
How to operate the CD player Buttons [5] and [6] Repeating the same track (REPEAT) 1 Press button [5] to repeat the track being played. To cancel, press button [5] again. Playing tracks in random order (RANDOM) 1 Press button [6] to play the tracks in random order. To cancel, press button [6] again. ATTENTION •Doing random playback, press button [5] to repeat the track being played. To cancel repeat play (go back to random play), press button [5] again.
How to operate the CD player [ (EJECT)] button [DISP] button Ejecting the disc 1 Press the [ (EJECT)] button. Disc is ejected. Displaying CD TEXT Only the built-in CD player supports CD TEXT. It can not be displayed with the optional CD changer. If the CD came with a logo shown below, it is recorded with a disc title and track titles. These information will be displayed during playback. 1 Press the [DISP] button. Each time the button is pressed, the following will be displayed in order.
How to operate the MP3 player How to operate the MP3 player About MP3 ATTENTION The making of MP3 files by recording from sources such as broadcasts, records, recordings, videos and live performances without permission from the copyright holder for uses other than personal enjoyment is prohibited. What is MP3? MP3 (MPEG Audio Layer III) is a standard format for audio compression technology. By using MP3, a file can be compressed to one-tenth the size of the original.
How to operate the MP3 player Media Media capable of playing MP3 includes CD-R and CD-RW discs. Compared to CD-ROM media commonly used for music discs, CD-R discs are fragile in high temperature/high humidity environments and one section of the CD-R may become incapable of playback. Fingerprints or scratches on the disc may prevent playback or cause skipping during playback. Sections of a CD-R may deteriorate if left inside a vehicle for long periods of time.
How to operate the MP3 player File names Only files with the MP3 file extension ".mp3" can be recognized as MP3 and played. Be sure to save MP3 files with the ".mp3" file extension. The "MP" letters of the file extension will be recognized whether entered as uppercase letters or lowercase letters. Caution If the ".
How to operate the MP3 player [DISC] button Button [3] Listening to MP3 file 1 Press the [DISC] button. This starts MP3 file play. Caution Playback may be intermittent when there is a scratch on a CD or when the recorded side is dirty. Note When music data recorded in the normal way (CD-DA) is present on the same disc with MP3 music files, the normally recorded music data will be played. To listen to the MP3 music files, press button [3].
How to operate the MP3 player [SEEK Buttons [1] and [2] ] button [SEL] button [FAST button ] [RTN] button Advancing to the next track (file) or returning to the beginning of the track (file) being played 1 Turn the [SEL] button to the left or right. Turn to the right: Advances to the next track (file). Turn to the left: Returns to the beginning of the track (file) being played. Repeat turning for previous tracks (files). Fast Forward /Rewind Fast forward or rewind the song currently being played.
How to operate the MP3 player Buttons [4] and [5] Playing the beginning of files (SCAN) 1 Press button [4]. Press the button briefly to play just the first 10 seconds of each song for all the files in the current folder being played. Pressing the button until [ALL SCAN] is displayed will play just the first 10 seconds of the first song in each folder. ATTENTION •To continue playing a desired track, press the button again to stop scanning.
How to operate the MP3 player [DISP] button Buttons [5] and [6] Playing files in random order (RANDOM) 1 Press button [6]. Press the button briefly to randomly play the files in the current folder being played. Pressing the button until [ALL RANDOM] is displayed will randomly play the files in all the folders. To cancel, press button [6] again. ATTENTION •Doing random playback, press button [5] to repeat the file being played. To cancel repeat play (go back to random play), press button [5] again.
How to operate the tuner How to operate the tuner [SEEK ] button [SEL] button [FM AM] button [FAST ] button First, press the [FM AM] button to start tuner operation. There are automatic and manual methods for setting stations in memory. The receiver will accept up to 24 stations in memory: six in AM and 18 in FM (6 each for FM1, FM2 and FM3.) (Initial setting) Tuning to a station 1 Press the [FM AM] button to switch to the desired FM or AM bands.
How to operate the tuner Buttons [1] to [6] [SEL] button [FM AM] button Entering stations into memory automatically (The automatic preset mode: ASM) 1 Press the [FM AM] button to switch to the desired FM or AM bands. Radio bands will switch from FM1 ➔ FM2 ➔ FM3 ➔ AM in order each time the button is pressed. 2 Press the [SEL] button for more than two seconds until a beep is heard. The automatic preset mode starts.
How to operate the tuner Buttons [1] to [6] [SEL] button [FM AM] button Manually setting stations into memory This section covers the setting of stations in memory under the numbered buttons. 1 Press the [FM AM] button to switch between FM and AM. 2 Turn the [SEL] button to the right or left to tune to the station to be entered in memory. 3 Select any button, from [1] to [6], and press it for more than two seconds. The tuned station is now memorized and set in the button selected.
How to operate the tuner Buttons [1] to [6] [SEL] button [FM AM] button Preset station scan This function enables reception of all the stations in the preset buttons for five seconds each. 1 Press the [SEL] button for less than one second. [P SCAN] will appear at the top of the display, and stations stored under preset buttons [1] through [6] will be played for five seconds each. 2 To stop the preset scan mode at a desired station, press the [SEL] button again.
How to operate the tuner Button [1] [FM AM] button Button [3] Changing the reception sensitivity for automatic scanning The deck lets you select the reception sensitivity to be used for automatic scanning of stations. The two sensitivity modes available for this deck are AUTO mode and DX mode. AUTO Mode During automatic scanning, the reception sensitivity switches automatically to one of two levels.
How to operate the tuner FM reception characteristics In general, FM has much better tonal quality than AM. However, FM and FM stereo reception encounter several characteristic problems not encountered with AM. FM is more difficult to receive than AM in a moving vehicle. The following are explanatory notes on what to expect from FM reception and on how to get satisfactory performance. FM reception differs from AM A characteristic of transmitted signals is that lower frequencies travel further.
How to operate the tuner Reception area of FM broadcasts A home receiver can catch weak FM stereo signals through the use of a tall, directional or ultra-sensitive antenna. In a moving vehicle, the area for good reception is limited because of varying conditions encountered while driving, including the types and heights of broadcast antenna structures, signal strength, engine noise, etc. For best reception with manual antenna, extend the antenna mast as far as possible.
How to use a Card remote control How to use a Card remote control Precautions in use of the remote control • Be careful when handling the control, especially because it is small and light. Dropping or striking it hard may damage it, wear out the battery or cause a malfunction. • Keep the remote control free of moisture, dust and water. Do not subject it to shock. • Do not place the remote control unit where it will get hot, such as on the dashboard or near a heater vent.
How to use a Card remote control [PWR] button Remote-control light receptor [MUTE] button [+] button [-] button Turning the power on/off When the power is turned on, the state used when the power was turned off such as CD and tuner playing is restored. 1 Press the [PWR] button. The power turns on or off each time the button is pressed. When the main unit is shut down, the remote control will not work. ATTENTION Adjusting the audio volume 1 Press the [+] or [-] button.
How to use a Card remote control [MODE] button [BAND] button Switching playback modes 1 Press the [MODE] button. Press the button to switch modes in the following sequence: Tuner Disc How to play the tuner Select the tuner mode first. Selecting the FM/AM band 1 Press the [BAND] button. Each press will switch tuner modes from FM1 ➔ FM2 ➔ FM3 ➔ AM.
How to use a Card remote control [BAND] button [ TUNE • SEEK [ PRESET CH ] buttons ] buttons Selecting a station (manually or automatically) A short tap of the button will allow manual station tuning. Pressing for more than one second will start automatic tuning. 1 Press the [ TUNE•SEEK ] button. [ ] button: Tunes to higher frequency stations. [ ] button: Tunes to lower frequency stations.
How to use a Card remote control [ TRACK • APS ] buttons [ DISC ] buttons Advancing to the next track or returning to the beginning of the track being played 1 Press the [ TRACK•APS ] button. [ ] button: Skips to the next track. [ ] button: Returns to the beginning of the track being played. (Press repeatedly to move to previous tracks.) ATTENTION Hold the [ ] button down to fast forward, or the [ rewind through the track being played.
How to use a Card remote control Replacing the battery Warning To prevent accidents, store batteries out of the reach of children. If a child has swallowed one, consult a doctor immediately. Use one CR2025 battery. 1 On the back of the remote control, while pressing the locking knob on the battery slot cover toward your right, pull out the battery carrier with your fingernail. Unlock 2 Remove the old battery, then place the new one in the carrier with the (+) mark facing up.
How to use an optional NOB remote control How to use an optional NOB remote control P H-M US O DE Remote-control light receptor BAND [AUDIO CONTROL] button MODE TRACK TUNE SEEK DISC [MUTE] button E-COM MUTE PWR [PWR] button ILLUMI Turning the power on/off When the power is turned on, the state used when the power was turned off such as CD and tuner playing is restored. 1 Press the [PWR] button. The power turns on or off each time the button is pressed.
[BAND] button H-M US O DE P How to use an optional NOB remote control BAND [MODE] button MODE TRACK TUNE SEEK DISC E-COM MUTE PWR ILLUMI Switching playback modes 1 Press the [MODE] button. Press the button to switch modes in the following sequence: Tuner Disc How to play the tuner Select the tuner mode first. Selecting the FM/AM band 1 Press the [BAND] button. Each press will switch tuner modes from FM1 ➔ FM2 ➔ FM3 ➔ AM.
[BAND] button [ TUNE • SEEK ] buttons H-M US O DE P How to use an optional NOB remote control BAND MODE TRACK TUNE SEEK DISC [ E-COM MUTE DISC ] buttons PWR ILLUMI Selecting a station (manually or automatically) A short tap of the button will allow manual station tuning. Pressing for more than one second will start automatic tuning. 1 Press the [ TUNE•SEEK ] button. [ ] button: Tunes to higher frequency stations. [ ] button: Tunes to lower frequency stations.
H-M US O DE P How to use an optional NOB remote control BAND [ TRACK ] buttons MODE TRACK TUNE SEEK DISC [ E-COM MUTE DISC ] buttons PWR ILLUMI Advancing to the next track or returning to the beginning of the track being played 1 Press the [ TRACK ] button. [ ] button: Skips to the next track. [ ] button: Returns to the beginning of the track being played. (Press repeatedly to move to previous tracks.
How to use an optional NOB remote control Replacing the battery Warning To prevent accidents, store batteries out of the reach of children. If a child has swallowed one, consult a doctor immediately. Use two AA-size batteries. 1 Remove the back cover of the remote control unit by gently pressing and sliding it in the direction indicated by the arrow. 2 Install the two batteries provided into the compartment as illustrated inside the compartment.
How to use an optional NOB remote control Caution •Be extremely careful not to swallow the battery. •The battery life is approximately one year. If the remote control unit does not operate correctly or if the button lamp gets dim, replace the batteries. •Be sure to orient the batteries correctly so that the positive and negative poles match the diagram. •Do not use one new battery and one old one; use two new batteries. •Use only two of the same kind of battery.
How to operate the receiver with an optional CD changer connected How to operate the receiver with an optional CD changer connected [DISC] button [SEEK ] button [SEL] button [FAST ] button Listening to a CD This section covers the operation of an optional CD changer that is connected to the receiver. To switch from another mode, press the [DISC] button. 1 Press the [DISC] button. Each press of the button switches the mode from CD Player ➔ CD Changer 1 ➔ CD Changer 2.
How to operate the receiver with an optional CD changer connected Buttons [4] and [5] Playing the beginning of tracks (SCAN) 1 Press button [4]. Tapping the button causes the changer to move up to the next track and play it for 10 seconds, then move up to the next track and play it for 10 seconds, and so on, on one CD, until the button is tapped again. Hold the button until the [ALL SCAN] display appears to play the first 10 seconds of the first track of every CD loaded.
How to operate the receiver with an optional CD changer connected Buttons [1] and [2] Buttons [5] and [6] Playing tracks in random order (RANDOM) 1 Press button [6]. Tapping on the button causes the changer to play the tracks on the currently playing CD in random order, until the button is pressed again. Hold the button until the [ALL RAND] display appears to play tracks from all of CDs loaded in the currently selected changer, in random order.
How to operate the receiver with an optional CD changer connected Buttons [1] to [6] [DISP] button [SEL] button Specifying a CD to play A CD of your choice is directly selectable out of the loaded discs. 1 Press the [SEL] button. 2 Press a button from [1] to [6]. Buttons CD 1 1 7 2 2 8 3 3 9 4 4 10 5 5 11 6 6 12 To select a CD from nos. 7 to 12, press the desired button considerably longer. Switching the display 1 Press the [DISP] button. Each press of button switches the display track No.
If you have a question: If you have a question: [RESET] button First check the items mentioned below before attempting to troubleshoot problems. Caution If a problem occurs, for instance when the unit does not respond to any button presses, or the display doesn't work correctly, press the [RESET] button using a sharp tool. Pressing the [RESET] button will delete all the entries from memory. The settings will return to those made at the factory prior to shipment.
If you have a question: Displayed information (for troubleshooting) The information listed in the chart below is displayed to show the status of the CD player and CD changer. Refer to the chart for the appropriate action. Information Code Table When "INFO " flashes on the indicator Nos.2~7 are displayed. Information Contents Explanation and remedial action to take 2 NO DISC LOADED IN THE MAGAZINE There is no disc in the magazine or player. Load a disc in the magazine. (Load a music disc.
If you have a question: Mode Problem Dead or weak sound Power does not turn on. Remedial action to take Refer to page Is the volume control up sufficiently? Turn up the volume control. 24 Is the fader or balance control set far to one side? Readjust the fader and balance controls to more normal positions. 25 Other probable causes include broken audio-signal wiring or a faulty speaker. Have your dealer check the problem.
If you have a question: Mode Problem Causes Remedial action to take Refer to page The disc cannot be inserted. The disc is ejected as soon as it is inserted. Or, the disc cannot be ejected. The disc cannot be changed. Is an extra label or seal applied to the disc? Do not apply labels or seals to the disc. 12 Are there rough edges, deformations or damaged areas on the disc? Try inserting another disc. Removed any burrs. Do not use a deformed or damaged disc. 13 CD Sound skips around.
Specifications Specifications Power Supply Current Drain Dimensions (W x H x D) In-Dash Unit Mass (weight) Usage temperature range Storage temperature range 14.4V DC (11-16V) 3A MAX 7" x 2" x 6-1/5" (178 x 50 x 158mm) Approx. 1.4kg -20°C to + 65°C (-4°F to 149°F ) -40°C to + 85°C (-20°F to 185°F ) Frequency Range USA: Asia/Australia: Usable Sensitivity Frequency Response Stereo Separation 87.75~107.9MHz (0.2MHz step) 87.5~108MHz (0.
Before installation Before installation Note Be sure to disconnect the vehicle battery's negative terminal before installing the receiver. Components No.
Mounting instruction Mounting instruction Mounting the main unit 1 Insert the mounting sleeve into the opening in the vehicle dash board or console box. 2 Use a screwdriver or the like to bend the tabs in the mounting sleeve to secure the mounting sleeve. BEND THE MOUNTING TABS. DASH BOARD OR CONSOLE BOX 2 3 MOUNTING SLEEVE Attach the side brackets to the main unit using flathead screws.
Mounting instruction 4 Mount the stud bolt to the main unit. 5 Insert the main unit into the mounting sleeve until it locks in place. 6 Fasten the rear of the main unit using either method [A] or [B]. Select method [A] or [B] to suit the interior configuration of the vehicle. 7 Install the bezel on the main unit.
Mounting instruction Names of lead wires and destinations (refer to Page 74) Caution Never connect the power supply to the speaker leads, otherwise it cause damage to the main unit. Note To prevent unconnected leads from shorting out, insulate them by wrapping their tips with electrical tape. Similarly, insulate the ends of connected leads. If an external amplifier is to be connected to the receiver, be sure to ground its outside housing to the vehicle body (a metal part). No.
Mounting instruction System CD3424 CD3424 CH3083 CD3424 CH3083 CH3083 73
3424 7 (–) (–) (–) (–) (+) (+) (+) (+) Never connect the power supply to the speaker leads, otherwise it cause damage to the main unit.
CD3424 Never connect the power supply to the speaker leads, otherwise it cause damage to the main unit.
CD3424 1.The switch on the back side of CD changer (A) must be set the "L" position. 2.The switch on the back side of CD changer (B) must be set the "H" position. Note Never connect the power supply to the speaker leads, otherwise it cause damage to the main unit.
Memo •••••••••••••••••••••••••••••••••••••••••••••••••••• 77
How to contact customer service How to contact customer service Should the product require service, please contact your nearest following Eclipse dealer. DIVISION OF FUJITSU TEN CORP. OF AMERICA 19600 SOUTH VERMONT AVENUE, TORRANCE, CA 90502 Phone: (310) 327-2151 FUJITSU TEN (AUSTRALIA) PTY LTD. ECLIPSE AUSTRALIA Phone: 1800-211-411 CSE Cobra. Sdn. bhd. Level 5, Axis Plaza, Jalan U1/44, Glenmarie, 40150 Shah Alam, Selangor D.E., Malaysia.
How to contact customer service HYUNDAI AUTONET Co., LTD. 1st FL. Namhyoung Bldg, 746-23 Yeoksam-Dong, Kangnam-Ku, Seoul, Korea 135-080 Phone: 02-508-6001 Fax: 02-2-508-6067 Transpectra Co., Ltd. 115-16 nonhyun dong kangnam ku Seoul, Korea. Phone: 02-540-4595 Fax: 02-2-540-4666 Sentrek Taiwan, LTD. 1, 9F, Lane 155, Section 3, Peishen RD., Shenkeng, Taipei Hsien, 222 Taiwan, R.O.C. Phone: 02-2662-8110 Fax: 02-2662-8117 Sho-Ten Co., Ltd.
Memo •••••••••••••••••••••••••••••••••••••••••••••••••••• 80
IMPORTANT RECORD YOUR “KEY CD” HERE… STORE YOUR “KEY CD” ALONG WITH YOUR OWNER’S MANUAL IN YOUR SOCK DRAWER.
CUSTOMER NOTICE Please retain this booklet and write in the serial number of your CD3424 for identification. The serial number is labeled or stamped on the chassis. Serial No. FUJITSU TEN LIMITED 090001-1454A700 0405 (Y.
